Glad it helped and hope the install went smoothly!

Good luck! Let me know if you have any issues

Glad it helped!

This is great to hear!

@@intheblackofficialchannel now I need you to help me with filter replacement, did everything, so easy bitty! But the Red Light didn’t shut off. Help me with that. 🤪thank You

@@4Wisdom4Strength find the button the on the front middle of the device, just above and between the CF and MRO lights (it has has 2 arrows in a circle). Push and hold for 5 seconds until you hear a beep. After you hear the beep, push the button again to cycle between the CF and MRO filter. When the light for the filter that you replaced is lit, push and hold for 5 seconds until it beeps and turns blue.

Glad it helped!

Awesome, glad it was useful

Thank you! Glad it helped.

Thank you!

Glad to hear it, hope the install goes well!

Glad it helped!

​@@intheblackofficialchannel thank you again, I didn't even need the manual just followed your steps to a T and installed in about 2 hours, 0 plumbing experience. Really appreciate this 🙏🏽

@@intheblackofficialchannel We ordered this unit yesterday and will be watching your video when we install it. Thanks!

Glad it helped!

Thank you!

Thank you!

Thank you!

Thank you!

The pump makes noise and it's loud enough to be clearly heard even if it's in the cupboard below the sink with the door closed. The sound doesn't bother me, but you will hear it every time you dispense water.

I unplugged my unit, gave it a minute, then plugged back in and the filter lights are still blue. But you raise a good point, does the internal memory remember filter life during extended power outages? I’m not sure. If you email service@waterdropfilter.com, they will give you a definitive answer. Worst case, put a note on your calendar to replace the CF filter 12 months after purchase and MRO filter after 24 months.

Saw you comment on two videos 😁. I hope by now,10month later someone has already answered you. But if not, I will.. you technically don't need to drill the hole that big, the size they are giving you is a pretty standard size,in case you ever need to install something else in that place like a soap dispenser or air gap. It's your house, if u want drill a hole big enough for the threaded piece to fit. Hope this helps

Based on your comment being 2years old you may not need the info anymore but they do make kitchen faucets that have a 2nd tap for filtered water. So you still need to replace your kitchen faucet but it only uses the one hope for both the main water and filtered.

I am satisfied with the G2. My only frustration is the "TDS creep" that exists with this filter (and with any RO filter of this type). This is where the first 10-30 seconds of water flow will have a higher level of Total Dissolved Solids (i.e., minerals) and possibly other contaminants due to the process of osmosis that occurs across the filter membrane while it sits idle. This means that if you want the most pure water, you need to allow the unit to run for ~30 seconds prior to taking water. This issue will be present on the G3, but it might be less pronounced. I am not sure as I have not used the more expensive unit. Other than this issue, I have zero complaints with the G2, I think it's a fantastic filter.

No issues other than the TDS creep problem that all RO systems have when they sit overnight. Still use it every day, just let the water run for 15-30 seconds before filling my glass.

I haven’t tried this, but it should work. You may need some additional fittings.

Filters are lower cost and changes less frequent when compared to similar RO systems. I love everything about this system except I have one gripe, which is that the TDS count is really high for the first 30 seconds you run the filter after it sits overnight. This is how Waterdrop gets the efficiency so high, the filters do not flush themselves every few hours like other systems do (including the G3 and competitors, not sure about regular G2). I’ve been meaning to ask the Waterdrop team what this means for overall filtration performance for the first 30 or so seconds after sitting for a while (TDS is just a small part of what is removed by the filter).

@@intheblackofficialchannel how high?!?

@@Aposerver about an 80% reduction in TDS at first, then after 30-45 seconds it hits 90+ reduction from whatever your tap water is at

Carbon filter every year for $30. RO membrane every other year for $100. So plan for $80 per year.

RO systems should eliminate 90% of TDS, so around 75ppm is a realistic target. If you run the filter for a bit longer, say 60 seconds, does TDS drop further? I’m in Gilbert AZ my water is about 550 from the tap and the filter will drop it down to about 40ppm after running for 45 seconds or more. I reached out to Waterdrop last year about this exact issue, and they said “this is a common phenomenon happening on all RO systems with tankless design.” They sent me another filter to install between the RO unit and the faucet and said that if I used it I wouldn’t “need to flush and wait for the TDS to become low anymore.” The model number on that filter is WD-15UD-RS. I have the filter but haven’t gotten around to installing and testing it. I can forward Waterdrop’s entire email response to me when I asked this same question, just send me an email at kf@kenafedorschak.com.

Hi, I just got mine this past week. I’m getting high TDS reading as well unless I let the system run off for 2 minutes and it drops it to about 38. I contacted Waterdrop about the issue and that’s the solution they suggested and was also offered the filter you mentioned and or a pitcher. Have you gotten to installing that filter? I live in Goodyear, AZ. My TDS readings are under 150 with the initial fill. I don’t feel like wasting water so I just drink then.

@@erjelmanalastas7924 yes, I installed the WD-15UD-RS filter about a month ago, and the water is about 5 TDS immediately after turning it on. Very happy with that result, but it’s a $50 filter and only lasts 3 months, so I’m not sure I’ll keep buying them…

According to the manual, feed (input water) should be no less than 14.5 PSI and no more than 87 PSI. You should be fine.

Just about to hit the 2 year mark, no change in performance, no maintenance other than scheduled filter changes.

While it’s running yes it makes a noticeable amount of noise

More filter stages, I haven’t tested the G3 so I can’t speak to performance.

@@intheblackofficialchannel In terms of taste, it shouldn’t be a big difference right?

The differences aren’t huge. The G3 has two extra filtration stages (7 instead of 5) so I theory it should remove more contaminants. It also has an automatic flushing mode, which wastes more water but also should help TDS creep, which is where it takes 30-60 seconds of water flow for the filter to reach peak filtration performance after sitting overnight / for an extended period of time.

That’s what I was thinking too

It should run when you start running water at the faucet. Can you double check to see that the input line, waste line, and output/clean water lines are properly connected?

The company claims 2:1 ratio, so half a gallon wasted per 1 gallon produced. I didn’t measure or double check their claim, but my guess is that it’s accurate.

Taste is largely determined by the Total Dissolved Solid (TDS) level of the water, which is a measure of the mineral content. Reverse osmosis filters (including this one) reduce TDS levels by about 90%. If you live on the coast or somewhere that rains lot, you likely already have soft water and a 90% reduction in TDS will make the water have almost zero taste. If you live inland or somewhere with very hard water, it won’t 100% remove all the taste. Any chemical taste (like chlorine) will be completely removed by a RO filter like this. Keep in mind that mineral content in bottled waters very quite a bit too, with some having very low levels and having little taste, whereas mineral waters will intentionally have high mineral levels to create flavor.

add the following post filter to make water taste better like bottled water. APEC FI-PHPLUS-QC