🏮 Presets for Behringer Crave: antonanru.sellfy.store/behringer/

Just finished tuning my Crave following your tutorial, 5 minutes ago. Makes a great difference! Thank you so much ❤

As you've noticed the one one the left is for 1v/oct tracking (scaling)and the right is for you default knob position if you like. This is for calibration, I'm assuming they have temperature compensation as it's an analogue circuit. You would normally set the reference frequency using the knob (eg: C2, doesn't really matter) and hit C3 and use the trimmer to adjust it. Go back to your reference and adjust the knob again and repeat the process until the scaling is correct. I would go 2 octaves, dial that in and then check 3 octaves and adjust if required. Once scaling is spot on set the Freq knob to centre and adjust the right trimmer to your reference. Same calibration for any VCO, there abouts. I noticed a similar issue with the Behringer 921 VCO...

Brilliant mate! I got my crave yesterday and immediately noticed tuning problems..I couldn’t find anything either. Thanks for this explanation

Thanks!!!!!! Finaly my crave is propperly in tune.

You’re so awesome, man! I’m doing this with my Crave, too! ❤️

You're an absolute legend. Thanks for sharing your secrets!

Very cool bud, thank you for the tip 👍🏻..

Perfect. Great information and well presented

Many thanks! Most useful

Thanks Anton! Very well explained!

Very helpful - mine was set to A-sharp or something, - I've now tuned it up and it's MUCH more useful.

Very valuable information!

Great to know! Thanks!

excellent, mine arrived today.. that's a really useful video... nice work.

Thank you. This video has very useful information

Thank you!

Very good tutorial. Very helpful

I wondered if this was the case but was not brave enough to try, but now will have a go later today thanks so much

Really good work, thank you!

Great vid bro. Thanks for sharing. ❤

Very helpful video.......Thanks for the help!!!

thank you.👍🙌

thanks for this helpful video!

🤟 Thanks Master!!!

Good job!

Thank you

"...so drop all your activities, buy a little screwdriver and do it. Goodbye." Awesome. I just got a Crave. I did notice the tiny recessed screws, but just added them to the list of a thousand other things I do not yet understand about the synth. And now, apparently, there are "notes" in a "scale" which have something to do with music. Who knew?

Thanks man!!!

Good to know, thanks 👊

Thanks for this video : it was veryvery usefull !

thank you man

really helpful, thanks a lot :-)

Many thanks

Thanks mate

Life saver.

thank you

Thanks man....

Thanks

i actually stopped gaming/watching another Crave video on 2nd screen when i saw THIS thumbnail and was like oh yeah I'm doing this today cuz I got all the tools!

You're making this look a lot harder than it actually is.. 😂

thanks

This is one of the "joys" of a real analogue synth. It can also be really frustrating trying to get the "scaling" correct over a wide octave range...it's probably possible with a modern synth like the Crave but it was impossible on my old Pro-One. I guess that just adds to its character!

Thanks! I just thought the Crave was not well tempered.

Once I made tuning my Model-D from a KZfaq tutorial . I did not watch this whole video, but I think the answer is the same as with Model-D. Now watch this video. :-)

I did the same with my Little Mcv. Use it to midi control an old MS20... That small but wonderful device works with either, V/Hz and V/oct, but each one requires a proper offset tunning...

Я вчера подбуханный джемил и тоже решил покрутить эти подстроечные резики. Теперь придется настраивать)

Hey man, I have some issues and would be so grateful if you will help. When I play a sequence and transpose it during playback, even if the MIDI-notes come from PC, even if i press the same key sequence starts - it transpose the sequence -2 octaves down. It works properly only with sequences in 4th octave and I don`t know why. The second problem is that when MIDI comes from PC the synth start playing, but doen`t end, when MIDI event ends. Thank you, your videos are great!

Its a common problem in analog synths. On some synths its not possible to tune the lowest vs the highest note, and therefor they should not be played with both bass and high notes at the same time, but be tuned for the used notes in the current song. You can hear the detuning problem on the Arp 2600, the Behringer Neutron and many other synths - but some of them can be tweaked somehow.

I just checked my Crave and when the Frequency knob is at 12 o'clock it is perfectly in tune (scaling and all) at A 440 Hz so I better leave it that way and not mess with it. The only inconveniece is that C key sounds like A but I can tune it with the frequency knob if I want to.

Cool, so first one is volts per octave range (midi) and second one is pitch shift. Liked the approach.

I tuned my Crave using the screw on the right and the other octaves are only 1 or 2 cents off, so I'm happy with that. But I wonder how to deal with the OSC knob. If it gets moved even slightly the tuning goes off. The only thing I could think to do is tape it down. Is there a better way to deal with this? If there was a click, or detent, so I knew the knob was centered then the problem would be solved. Any suggestions better than taping down the OSC knob would be great!

Have a look in any 3340 diy vco module. They explain how to calibrate.

Standard calibration for any analogue synth. One is tuning, the other is called 'Scale'. If you mess it up too much you can spend hours trying to fix it. My polivoks is a pain to tune!

Интересно, почему они не сделали тоже самое в Нейтроне

Awesome, thanks for sharing! I gotta ask: what tuner are you using?

I followed the Behringer advice video on here for tuning my Model D and they ask you to tune it to an A note (A2 and A5 for each screw respectively)... Just wondering why the crave is tuned to a C note?? Thanks for posting this video!!! I got my Crave from Thomann and i think it's been out of tune since Day 1, so hopefully this sorts it!!! Now i just need to find out why my sequences are playing around 2 to 3 times faster than the clock that is coming from the RD-8... Anyone any ideas about that??

Hey Anton, could you please help me out. Notes have mysteriously dropped in volume compared to others. Is there a way I could get them back even with the others?

Anton, bro)) thank u for video. Is there any control of pitch range which we get from this freq osc nob near those screws? Короче, Бро, привет) мы как-то можм поменьше поставить freq диапазон? Я когда ручку поворачиваю полностью влево или вправо было бы логично на октаву получить шаг. Но к меня намного больше.

What tuner did you use? I need to tune my Crave, thanks for this tutorial.

Хорошо темперированный клавир

But what is that little application that show you values?

спасибо за видео! для тех у кого нет такой отвертки, нужно сломать заколку-невидимку вашей девушки, и заточить ее конец пилочкой (если нашли заколку, то и пилка возможно неподалеку)

How offen do you have to tune it? Just one time or everytime you wanna Play with It?

Антон, добрый день. Crave мой первый аналоговый синт) подскажите, из-за чего ableton видит не все ручки синтезатора? Пробовал на двух компах, везде одинаково. Не нашел видео с подключение его к ableton. Спасибо.

Great video, should we calibrate our crave because original it is unruly?

Hi mate, screw on the left is pitch tune c2 do this one first, one on the right is scale tune c5. Double check 3340 docs to make sure though😊 it might be A on each octave like the model d

Thanks but did not need it cause mine was perfectly calibrated.

What's the name of the tuner you are using?

What kind of tuner are you using?

Intonation (music)

Jak w gitarze, stroisz na główce i musisz ustawić menzurę na mostku.

dont care for perfect tuning is you buy analog (its the charm) , these holes are very common since they calibrate the midi side to the analog side , scale is the offset in the 12 note interval , mess with that and it an take long before you find it again ,been doing this routine on kenton interfces since 30 years

Sounds like "Equal Temperament" to me.

Bro the biggest secret of this modern society is 432hz tuning and big healing properties of frequencies in 432hz = A spectrum. Lot's of ppl now making music by tuning their vst's to 432hz = A and repitching all of the samples 8hz down. This is amazing that crave can be tuned.

Здравия. Есть вопрос к владельцам Crave. У моей модели не работает сиквенсер. Есть ли тут люди с подобной проблемой?

it's just like on a x0xb0x

Юси? Юси

If you don't know what those are then don't touch them. They are for tracking and will have been set up at the factory so you get 1v per oct. Then again if you are not bothered about your crave being able to stay in tune across all your octaves then feel free to mess 😉

Май лук тюна

Добрый день, а можете обьяснить почему будучи русскоязычным человеком, вы записываете видео на английском?

Thank you!