Wheel Hub Bearing Removal with Lisle 40100 Hub Removal Tool

Рет қаралды 2,148

5 ай бұрын

Demonstrating a very handy tool for removing stuck bearing/hub units
This video is in no way sponsored. It's just a tool that I like and bought with my own money.

Пікірлер: 22

@trondfiskeseth2559 11 күн бұрын

tip: use a steel plate on the caliper attachment to distribute the pressure from the tool

@SuperKONR 4 ай бұрын

That sure beats a hammer and a torch! I still don't miss working on FWD cars though lol. Have to do the wheel bearings on a friend's Saturn soon, everything is pressed together instead of bolted into the knuckle. I think there's a tool to do them but I've always just pulled the strut and knuckle as one piece and stuck the whole mess in the hydraulic press, so it doesn't need an alignment afterwards. Maybe I should just look for the tool this time LOL.

@MattsRageFitGarage 4 ай бұрын

I may have to buy that someday. I helped my coworker rebuild the front end on his 2010 Chrysler T&C and the front right wheel bearing failed catastrophically, I got that one out with my big axle slide hammer without much fuss. Decided to put a new bearing hub in the driver side but gave up since it was still good and we were running out of time, that thing didn't want to budge at all. That front right bearing was so bad the lugnuts burned me when I dropped them out of the impact socket into my hand, wasn't expecting that.

@Krankie_V 4 ай бұрын

This tool is a huge time saver. I use it all the time at work. I finally ordered one for home after I had two people ask me to change wheel bearings for them at home. We have one of those "hub shocker" tools at work also, the one you bolt to the hub and whack with a hammer. This one is easier to use, though.

@bobbyu8991 2 ай бұрын

This tool has failed to remove the last two I did this tool is junk will damage spindles if this works you didn't need it in the first place will not remove badly stuck bearings

@Krankie_V 2 ай бұрын

@@bobbyu8991 I'm going with user error.... I have used this tool on very stuck bearings without damaging anything. You're doing something wrong.

@AnimeBaller22 2 ай бұрын

Hi Krankie, I a saw a comment of your about fixing a stolen kia in your shop. May I ask how much it costs/how easy is it to fix just to get the car running again? Mine wouldn't start but I don't know if that's because the electricals we unplugged or whatever they did. Thanks

@Krankie_V 2 ай бұрын

I believe it was around 2000$ but can't be certain. The billing is not my job, and it was handled by insurance anyway. That car started and ran just fine though. Just a lot of damage to the steering column

@elmayimbe_the_amateur_mechanic 2 күн бұрын

1000lb-ft cordless impact should work with this right?

@Krankie_V 2 күн бұрын

@elmayimbe_the_amateur_mechanic it works, but be careful because if you just go to town on it, it's possible to cause damage. Normally I just use a ratchet so I can feel what's going on

@elmayimbe_the_amateur_mechanic 2 күн бұрын

@@Krankie_V , thanks. I have 2 of the same cars. A 2002 and 2005 Infiniti Q45. Here in San Diego so no rust. The 2005 needs a ton of work and has sat for a year. I have had all 4 hubs and both LCA's for over a year now. Gonna experiment on the 2005 with this. If it goes well I will just leave the old hubs on and put the new ones on my 2002. Thanks.

@Krankie_V 2 күн бұрын

@@elmayimbe_the_amateur_mechanic with no rust, you probably don't even need this tool

@elmayimbe_the_amateur_mechanic 2 күн бұрын

@@Krankie_V, I did rusty front hubs on a 2013 Ford Explorer from Virginia. Scared mr for life. I am using this thing for sure. I want this to be as easy as possible.

@DaDaDo661 14 күн бұрын

Are you in the rust belt?

@Krankie_V 14 күн бұрын

Big time. Upstate NY

@nazigrammar9728 26 күн бұрын

This tool is almost useless, at least for most of knuckles(backing plates or caliper mounts will get a damage)

@Krankie_V 26 күн бұрын

Not true.... I have used it many times without damage

@nazigrammar9728 26 күн бұрын

@@Krankie_V I've just checked on Amazon and many people said the thread on a rod is so weak, even on an item it's described as Upgraded. Where did you get urs from?

@Krankie_V 26 күн бұрын

@@nazigrammar9728 I bought my own from rockauto and thr ship I work in has one that came from matco tools

@DaDaDo661 14 күн бұрын

What's worse? Ruining a cheap back plate? Or giving up and bringing the car to a shop that will charge you $500? I don't understand the backing plate argument, just cut it off, buy another one or don't put it back on

@nazigrammar9728 14 күн бұрын

@@DaDaDo661 many backing plates are not available. Many of them are crazy expensive, even older Toyota's. I work for a small used car dealership, so I know what I'm talking about