Worcester Bosch right hand block change

Рет қаралды 22,942

3 жыл бұрын

DISCLAIMER:
This video is only intended for use by qualified Gas Safe Registered engineers. You must not attempt any work on your boiler if you are not qualified. You must always carry out 26.9 checks upon completion of works on a boiler.
~
Here's how to change a right hand block on a Worcester, also known as the return unit.
Soak all connections in WD-40 for a few mins beforehand and use plenty of silicone grease on the new parts.
The block had split on the cold mains side so needed replacing. When replacing the right hand block I always replace the flow turbine adaptor because it always breaks when you remove it and the PRV as well whilst I'm at it. The new block comes with a new diverter built in so you don't need to replace that.
A lot of people struggle with the bypass, but if you see in the video, I wiggled it out of the left hand block by removing the gas pipe connection so it gave me more room to manoeuvre it out.
Part numbers given below:
Right hand block 87161064420
Flow turbine adapter 87161064330
PRV 87161064310

Пікірлер: 83

@jimmyfreemantle879 2 ай бұрын

Just done my first RH block today following your excellent video. I also did my second RH block straight after. Both boilers were CDIs Thanks for your easy to follow video. I also used your flow turbine adaptor video during the same repairs.

@cputilitysolutions 2 ай бұрын

Nice one glad it helped! 🙌🏾

@d.costacostagliola7298 3 жыл бұрын

Great video mate, top quality filming as well. I'd say this channel is fast becoming my favourite for gas engineer. This kinda stuff is super helpful for myself, I recently qualified as a gas engineer so trying to pick up as much as I can before I go out on the tools.

@cputilitysolutions 3 жыл бұрын

Thanks mate, glad you're finding it useful 👍🏽

@tyronewest8163 Жыл бұрын

Bro you’re videos are literally life saving. Thank you for sharing the knowledge brother 👊🏿❤️

@cputilitysolutions Жыл бұрын

Nice one 👊🏽

@andyplumbing5676 2 жыл бұрын

Honestly your videos are excellent. Keep up the work bro

@andymav3023 2 жыл бұрын

Good videos mate helped me build a lot more confidence with repairs 👍

@danielwilll 2 жыл бұрын

As a installer not a breack down engineer I was able to follow this video and do the job thanks again

@cputilitysolutions 2 жыл бұрын

Nice one mate 👍🏽

@richardhodgson7443 3 жыл бұрын

Top video, love these strip down repair jobs, keep them coming please 👍

@richardpayne2456 3 жыл бұрын

Good video mate very helpful with a great talk through on what your doing and why 👍

@cputilitysolutions 3 жыл бұрын

Thank you mate 👍🏽

@paulrossiter9567 3 жыл бұрын

👏👏👏👏 top work once again CP. Very clear 👍

@cputilitysolutions 3 жыл бұрын

Thank you mate 👊🏽

@SuperGVIBE 2 жыл бұрын

Thanks buddy done this job 1st time today your video helped alot job well done.

@jamiethackway2475 3 жыл бұрын

Love strip downs mate, done most of these but look forward to jobs I haven’t done yet. Keep them coming.

@cputilitysolutions 3 жыл бұрын

Thanks mate

@zali1457 3 жыл бұрын

Very nice and topman keep up the good work mate

@buggalugs 2 жыл бұрын

Clear and no BS.... well done

@cputilitysolutions 2 жыл бұрын

Thank you 👍🏽

@user-hm9fg6jl8t 6 ай бұрын

Going to do one soon mate. Thanks for the video.

@cputilitysolutions 6 ай бұрын

Nice one good luck!

@madmaycon2531 5 ай бұрын

Thank you very much for sharing this with us. Top video !!!

@cputilitysolutions 5 ай бұрын

Nice one 👍🏾

@teachweb69 2 жыл бұрын

Thanks so much for this video I really can't thank you enough I wasn't sure whether I could do this and your video really gave me the confidence I needed. You're doing amazing thing

@MrAvant123 Жыл бұрын

Great vid, just had this done as I was not confident enough, so wish I'd seen this...

@cputilitysolutions Жыл бұрын

Sometimes doing it yourself is the best way. The next time will be much easier 👍🏽

@bahiaharjinder 3 жыл бұрын

Thanks for sharing good job 👍🏻

@FLYNN.. 3 жыл бұрын

Good work

@leaturk11 2 жыл бұрын

Nice job

@UmarKhan-ww8jl 2 жыл бұрын

Nice video very helpful will start doing this to my boiler my flow unit is leaking, just want to know how much was the unit and where did u get it from ? Thanks

@rayc1503 3 жыл бұрын

You made this look so easy. The big question is how did you manage change the rh manifold block without cutting your hands. Worcesters pretty much always need a shock arrestor. Even if there isn't a water meter present. Slowly looking through your library of uploads 👍🏼.

@cputilitysolutions 3 жыл бұрын

Thanks man, black mamba gloves 😉

@mrseb99 3 жыл бұрын

Awesome mate, hope customer paid for the block

@cputilitysolutions 3 жыл бұрын

Yup, I'd pointed it out already before I started on the plate so they knew

@everydaybiker Жыл бұрын

Fantastic, thank you

@cputilitysolutions Жыл бұрын

Nice one mate

@Smokeblow 2 жыл бұрын

Made it look easyyyyy

@jmqmin 3 жыл бұрын

Good job mate, how did you manage to get the return brass nut into the return manifold? Every time I do it, it’s a pain in the arse. Also what light are you using please?

@cputilitysolutions 3 жыл бұрын

Thanks mate, it took a lot of swearing and sweating! I tried to put it on a flat surface and then push the manifold onto it. The 2 lights I'm using are Unilite SLR 500 & 1750 👍🏽

@ianbrooks6816 2 жыл бұрын

Nice.

@Davidsmith-zw3kj 5 ай бұрын

Hi. What would you charge to do this job. I have a leak from exactly where you show in this video. I feel confident to attempt this as I have already replaced the flow turbine a few years ago. Just would like to know if it would cost a lot to get someone out to do it. Many thanks

@cputilitysolutions 5 ай бұрын

Hi mate, for this job I would charge £160+vat labour plus the part

@Davidsmith-zw3kj 5 ай бұрын

Thanks for your reply. Very much appreciated

@luzico 9 ай бұрын

Great video mate. What are the part numbers for all the parts you changed in this video?

@luzico 9 ай бұрын

Sorry mate. I just saw it on the notes. Keep the good work mate.

@cputilitysolutions 9 ай бұрын

Nice one 👊🏾

@Morecocksthanhands Жыл бұрын

I've just replaced the right hand block due to a leak.. I've set the pressure is at 1.2 bar.. I have 2 flashing resets to one flashing blue.. and its locked out. Any ideas where I should look? I've bled to top bleed on top of the silver cylinder.. that's all I've done. Please help me

@cputilitysolutions Жыл бұрын

Have a look at the MIs, the fault finding section will tell you what the sequence of lights mean 👍🏽

@Morecocksthanhands Жыл бұрын

@@cputilitysolutions thank you. Whats the 'Mls'? Do you mean the hand book? That says the light sequence is 'ignition lockout' due to; gas present and pressure, gas valve- ohms etc, combustion CO2, flue condition, blocked condonation pipe, gas valve adjustment, ignition electrodes - harness/ connections replace circuit board.. Somethings wrong, I think the board.. it's 20 years old.. I'll let you know one I get my multimeter out

@cputilitysolutions Жыл бұрын

Yes that's it (Manufacturers Instructions). Check all the usual basics of ignition and you should be able to find the fault 👍🏽

@Morecocksthanhands Жыл бұрын

@@cputilitysolutions You're so kind. I'll try my best today. I'm a hairdresser you see.. You've got a really good channel helping us all out.. I know my way around a circuit board tho.😉😉 all the 👌

@Morecocksthanhands Жыл бұрын

@@cputilitysolutions I fixed it! I checked the MI, it mentioned PCB. The pcb was wet, plus mineral deposits in area's, I cleaned them away with electrical contact cleaner/alcohol and a sonic tooth brush. Dry and she's up and running.. Really good video.. You've saved me so much money I'm sure. Thank you so much for your great video and time. xx

@gbzl3691 2 жыл бұрын

How long in real time did it take you ? Amazing video 👏

@cputilitysolutions 2 жыл бұрын

About 90mins

@gbzl3691 2 жыл бұрын

@@cputilitysolutions brilliant 👏 👌 👍

@lostinthoughtscalminsilenc8167 10 ай бұрын

How do you fill the rads on sealed system?

@cputilitysolutions 10 ай бұрын

With the filling loop

@lostinthoughtscalminsilenc8167 10 ай бұрын

@@cputilitysolutions so 1 bar of water fills a whole system?

@cputilitysolutions 10 ай бұрын

@@lostinthoughtscalminsilenc8167 yes

@jasonbrooksbank 3 жыл бұрын

Did one today right hand block. Took me 2 hrs. Took all the block out. Riped my hands to bits.

@cputilitysolutions 3 жыл бұрын

Ah man, yeah they can be a nightmare. I try not to take the whole block out if I can help it

@jasonbrooksbank 3 жыл бұрын

@@cputilitysolutions I really struggled with getting the nut to bite on the return valve. Think I might try your way next time.

@-Anon-Ymous 5 ай бұрын

@@cputilitysolutions Another highly appreciated video from yourself. How much to price up for exactly the same as this as a job? Thanks

@cputilitysolutions 5 ай бұрын

@@-Anon-Ymous labour I charge 160+vat

@gazzagasco 2 жыл бұрын

How much do you charge to replace that manifold

@cputilitysolutions 2 жыл бұрын

£150 labour

@gazzagasco 2 жыл бұрын

@@cputilitysolutions thanks pal

@joncoke8208 3 жыл бұрын

Did one thurs

@suheilhanna873 10 ай бұрын

🎉🎉🎉🎉🎉

@cputilitysolutions 10 ай бұрын

👍🏾

@jasperstainthorpe3236 2 жыл бұрын

Nice Vid good if you name tools your using ☝️😀

@SisterAbdullahX Жыл бұрын

Nice job, fella. I hate Worcesters. I remember the first time I changed a left hand block, I was nearly in tears!😂

@Marc-wg2mr 4 ай бұрын

How much should a job like this cost a customer?

@cputilitysolutions 4 ай бұрын

I charge £160+vat labour

@Marc-wg2mr 4 ай бұрын

I've been quoted £390 all in

@cputilitysolutions 4 ай бұрын

@@Marc-wg2mr sounds about right with the parts included

@Marc-wg2mr 4 ай бұрын

@@cputilitysolutions Thanks - just wanted to make sure I wasn't being ripped off!

@jackhoskins722 3 жыл бұрын

The dreaded right hand block 🤦🏼‍♂️🤦🏼‍♂️

@acefreaky2988 Жыл бұрын

Very helpful and tbh shows worcester for the over engineered junk they are.

@cputilitysolutions Жыл бұрын

Yup absolutely! Thanks for the feedback 👍🏽

@andrewbarry9674 2 жыл бұрын

Worcesters are terrible all have the exact same problems, cant belive I am saying this but I would rate an ideal higher than a worcester 😲