Yamaha Raptor 700R Engine Build Part 7: Head Installation and Valve Lash

Yamaha Raptor 700R Engine Build Part 7: Head Installation and Valve Lash | Partzilla.com

Рет қаралды 28,947

Күн бұрын

See the components for part 7 of our Yamaha Raptor engine build here:
bit.ly/Yamaha-Raptor-Engine-Bu...
Note: our phone number has changed! Call us at 1-229-584-0046 for help finding the right parts for your maintenance needs.
In part 7 of our 2017 Yamaha Raptor engine build, we’re ready to install the cylinder head. We’ll start by getting the head gasket on, and then we’ll show you the torque settings and the tightening sequence to get the head installed to Yamaha’s specifications.
There are a couple of other parts we’ll install, including the thermostat and an oil delivery pipe. We’ll also set the valve lash on our Yamaha Raptor 700, showing you the valve lash settings on the intake and exhaust sides.
Go back a step and see us install the valves in part 6: • Yamaha Raptor 700R Eng...
See the Yamaha Raptor engine build from start to finish here: • 2017 Yamaha Raptor Eng...
Check out these diagrams to see where we’re working:
Cylinder head diagram: www.partzilla.com/catalog/yam...
Valve diagram:
www.partzilla.com/catalog/yam...
Camshaft and chain diagram:
www.partzilla.com/catalog/yam...
Oil pump diagram: www.partzilla.com/catalog/yam...
What causes gasket failure? Read about it here: www.partzilla.com/blog/gasket...
VIDEO HIGHLIGHTS:
Installing cylinder head gasket - 2:00
Installing the cylinder head - 2:48
Installing the cam chain sprocket - 4:20
Installing the thermostat - 6:55
Setting valve lash - 8:42
Installing engine covers - 11:09
Installing spark plug - 11:50
Find thousands of Yamaha ATV parts here: www.partzilla.com/catalog/yam...
Talk to us:
Twitter: / partzilla
Facebook: / partzilla
Instagram: / partzilla
In the video we’re working with a 2017 Yamaha Raptor 700R, but you may have similar steps for your Yamaha ATV. If you’re not sure whether these steps apply to your machine, leave a comment and we’ll get back to you.
RELATED CONTENT:
Yamaha R6 engine build playlist:
• Yamaha R6 Engine Rebuild
Yamaha YFZ450R repairs:
• Yamaha YFZ450R Repairs
#yamahaatv
#partzilla
#atv

Пікірлер: 42

@cellujuegos7844 2 жыл бұрын

woww , he make it look so easy, than it really is, i dont think i can make it, even with all the right tools

@goldenboygq9 4 жыл бұрын

These videos help so many people out thanks again!

@kcampbell4098 4 жыл бұрын

you have an amazing amount of patience...oB

@daghbos Жыл бұрын

Clear explanation, thank you so much

@garyrideout1470 8 ай бұрын

Thank you. Great job

@Jweiss7939 3 жыл бұрын

You are a great help and these videos are greatly appreciated.

@MxHDXB 5 жыл бұрын

Excellent quality and standards.

@machadomotos2104 4 жыл бұрын

Excelent great video!! Saludos desde Argentina!!!

@Timmyskills 4 жыл бұрын

Hey, good stuff man!

@richardsharpe7356 4 жыл бұрын

Fantastic video John, I really enjoyed it. Keep up the good work!

@zachwithastache7898 2 жыл бұрын

I’m

@Firestorm637 3 жыл бұрын

Thx...wonderful job!

@alejandrogrisales7151 5 жыл бұрын

Como siempre ingeniero muy profesional todo organizado la limpieza todo gracias por compartir este valioso video...como lo mencione antes que dicha que tubiera traduccion a español

@arbabsultan2938 4 жыл бұрын

Very nice.

@MaliceInCyberland Жыл бұрын

Well organized, well edited, well detailed, and very well explained to the point that, as an amateur mechanic, I have zero reservations to perform this myself should my Raptor ever need such work... I was just looking for the oil-bleed bolt torque... Thanks!

@PartzillaParts Жыл бұрын

Wow, thanks!

@MatveyRF 4 жыл бұрын

Best

@joevega748 2 жыл бұрын

If timing is off by a tooth will it affect timing.

@andrewvantassel5181 2 жыл бұрын

Yes

@oscaresquivel4740 Жыл бұрын

Would this also apply to a yamaha 700 viking ?

@greggan100 5 жыл бұрын

You forgot to torque down cam sprocket

@PartzillaParts 5 жыл бұрын

They were torqued to 14 ft-lb as called out at the 5:55 mark. We just missed catching it on video!

@greggan100 5 жыл бұрын

@@PartzillaParts i was waiting for you to go back on to it after cam tension install lol Brilliant videos as usual and very satisfying. Keep it up👌👍👍👍

@PartzillaParts 5 жыл бұрын

@@greggan100 Glad you are enjoying them and great catch! We considered going back and re-shooting it but the engine had already shipped out to it's new owner.

@ryanwofford1482 5 жыл бұрын

Where did you get the torque wrench at and how much is it to buy ??

@zacharyadams6277 4 жыл бұрын

It's just a snap on. You can get it on the tool truck. Probably around $200

@quahu1472 5 жыл бұрын

Can i take what ive seen here and apply it to a 01 raptor 660r engine???

@PartzillaParts 4 жыл бұрын

Similar concept, but different motor.

@travissprague7775 2 жыл бұрын

At 5.40 when u say becarfull not to drop them well I did drop one how far do I have to go in to the bottom end to get it back out just the crank case I hope plz help

@mitchelldaniel2350 Жыл бұрын

Did you get it? I’d pull the crank side case cover off.

@travissprague7775 Жыл бұрын

@@mitchelldaniel2350 ya I had to pull the cover and magneto was not fun but did my timing chain while I was in there

@mitchelldaniel2350 Жыл бұрын

@@travissprague7775 I did something to the same extent. Dropped a wrist pit for wrist for piston down in the motor. Got it out luckily. Thought I was about to be splitting the motor. Stuffed some clean rags down in the hole gave it another shot, and got it. That’s one of them mistakes that you’ll only make one time.

@arbabsultan2938 4 жыл бұрын

Yes r u Selind Tools.