Great video had a question, If water got into the gas tank is this where the water would accumulate?

Muchas gracias, help me fix mine, getting ready for hurricane season from Puerto Rico!

yup my 1998 polaris magnum 425 died no spark. Put a new exciter coil on for 20 bucks. No dice. Gonna try your video method. Thanks

Thanks for the video!

I’m looking to buy one of those diesel 3010s. The guy said it was running hot. When he went to change the head gasket. He saw one piston was kind of burnt up. I’m a little worried about repairing the diesel but that would be nice. I also have, a good running motor out of a mule 550 but I wonder if I can swap in? any advice you can lend would be much appreciated. I’m enjoying the videos.!

Got the same mower with a 60 inch. It is a grass cutting machine and the air is so cold it will give you a head ache blowing right on your head. I am in Alabama.

TO ALL WHO ARE HAVING TROUBLE DISASSEBLING THE CLUTCH: I was unable to unscrew the aluminum piece on my clutch after lubrication, heat, and brute force. Here is how I did it: 1-1/16" 3/4 drive 12pt socket. Cut two slots 180 degrees out from each other so that when you place it over the shaft it fits over whatever you use for the pin to go through the shaft holes. I used a 1/4" impact driver extension bit (good grade tough material). Hold the aluminum threaded hub with a gloved hand or clamp it some kind of way, I just held it. Be sure that since you are turning the shaft the impact is turning clockwise. Give it hell. 3/4 impact level hell. Good luck to you all and many thanks to @atvrepairsandmore2482 for taking the time to share your work!

What oil filter did you use

Carefully placed hose pinch pliers prior to disconnection avoids the mess too

Spray carb spray on any type of hose connections prior to removal. Helps slide them off. Takes the fight out. 55's in automotive taught me.

Just bought one of these, sitting for years. Will be watching your series to get it cleaned up

I thought I had a fuel filter problem.But you just showed me that My gas tank valve turned off.I didn't know which way was on or off.Thank you so much.

Looking for a Kawasaki mule diesel engine ?

Can you ride like this?

I’m considering this mower deck and tractor. I’ve heard nothing but issues with noise and performance over all. How has it been performing ?

Thanks for the video. I hope those scratches on your hands healed!

Hello, Are you interested in testing our products? We would like to invite you to test the Camo Seat Cover for your Kawasaki Mule 3010 Diesel 4x4 (if your car year is 2003-2008

Im south of Houston and Pearland. Whats your contact information

1 yr old Gen 4000, rotor and stator dead, no power. $150 for parts…

I found an easier way. Remove wheels Knuckles Cv axles, next remove the bed, Exhaust shields Exhuast Top transmission mount Number the cables, brackets and hoses, remove them. Remove the starter Remove back cover behind the HST Remove sway bar bracket and swing the swaybar down and remove the two bolts on the lower transmission mounts. Now block up the engine and hoist the transmission out of the sub frame It fits out without having to take apart the suspension and sub frame. Also goes back in way easier

I have a 2005 3010 and the primary clutch was stuck fully in engaged, would not release. Only 300 hrs on the clock so should not need rebuilt. I was wondering if I could rub some grease on the fly weights or the rollers that they slide on? I first thought of silicone spray but afraid it might get on the friction surface of the belt or pulleys. Any other thoughts appreciated. Thanks in advance.

I have a 2510 mule. I had to hard wire the fuel pump to the key. Do you have any ideas on why it would stop working

I have no spark I replaced the coil staor and starter new spark plug no spark on a 1996 polaris xplorer 300 4x4

I've got one for sale here in Indiana

Thank you so much for the detailed instructions! I have a 3 year old EU2200i that was brand new in the box, never used, and wouldnt start. Gas tank full with new gas, oil level good, air filters clean, spark plug correctly gapped. I followed your instructions and found that the main jet was completely clogged. After cleaning and reassembling, it started right up on the third pull. Thanks for saving me a couple hundred dollars! ps I noticed you forgot to reattach the fuel line and had to re-do the air filter housing ;p

Koman yo demonte bòl devan kigen leman

If you did strip the brass jet trying to unscrew it, what would you do?

DUDE STAND Fin STILL OMG

How u do pulley for alternator on engine

Thanks for the explanation and demonstration. Videos like this make DIYers like myself's job a lot easier.

How did you take it out. Did you use special tools?

Great video! Appreciate the time you took, hadn't ran mine in a couple years and it literally fired right up after I followed your very detailed steps!

Thanks for your video. I was in the middle of changing my Bendix and when it would not come past the flywheel I started searching for videos. I found yours and one other very helpful. The other one mention taking the Bendix apart by removing the retaining ring. I found removing the retaining ring to be next to impossible while it's still in place. As a last ditch effort I twitched it to the left and it fell out into my hand WITHOUT removing the flywheel. (the starter has to be removed to allow room to make the swing)

Awesome work saved me $500

That mower is awesome. I didn't know anyone made something with an hvac cab for a lawnmower. Thanks for sharing.

Thanks ❤John 3,16 ❤

The tricky thing with this job is unbolting that flange, most UTVs are not designed with a flange like this!

Thank you!!! You're the only one I found with a good visual on how to put this midmount together!

Audio very low.

Got it going. Thanks for sharing~~!~~

This is a good, to-the-point video! Three questions: 1. Do you still have -- and use -- this generator? 2. Do you still recommend this generator? 3. (I'm not familiar with generators of this kind, so forgive my ignorance . . .) Is this generator safe for running electronics (TV, PC, window a/c) or should I get one that has an inverter? Thanks, -- Old Matt

How wide is your bucket? Thanks for video!

What’s the name of the Facebook group? I have 2 rtv-x1100 that won’t go into reverse so I’m hoping to get some pro tip fixes before I have to rebuild the transmission. Thanks for your time

Its cool to finally see content on this great atv! Bought mines back in 2015 still have it to this day been sitting for a while but starts runs smooth with this video itll be easy to do some much needed work to it! You still have this one?

Thank you. Just bought a 1995 Kawasaki Mule 2500 and I believe it needs to be rebuilt so thanks for taking the time to walk through this.

What type of fluid does it take?

What is the Facebook site you recommend? Cheers

Hi mate, I have a rtvx900 and it has just happened to me, I would imagine this should be the same transmission as your unit? Cheers

Part number for the part that goes in the front of the case ?

Thank you. Your videi help me a lot. My generator works fine now Thanks a lot. You are the best