John deere turbo, fucking mad man, stay manual tho plz

Do you need to map the egr out when you remove tho?

How waa the vacuum lines ran when you were finished? And also the plug goes where?

I might do this. It's good hearing a local voice. G'day from the Goldy.

Where can I reach out to you Sir ? 🙏

Hi, Mate Where did you source your your light bar??.. I'm in country vic, and the same issue of not being able to see out on the roads where I am like yourself... So I'd be very interested to obtain the same light bar as yours, so I was wondering where u sourced it from.. Cheers mate

Hi, Mate Where did you source your your light bar??.. I'm in country vic, and the same issue of not being able to see out on the roads where I am like yourself... So I'd be very interested to obtain the same light bar as yours, so I was wondering where u sourced it from.. Cheers mate

Hey, what brand light bar??? ... or where did you source your light bar???..

Would this be useful for getting dead skin and other dirt off of bass strings to make them sound fresh again? Bass strings are now £30+ for a new set.

You should hear my straight piped Caddy 1.9 with the EGR off. Wahhhh choooooo! Coolest van in Australia. Lol

I have an R36 Wagonwith a cat and resonator delete, and it just sounds beautiful. The VR6 is just the best sounding 3.6 ever.

If the sensor breaks as shown on your video. Will it give an open circuit code?

what can I do about the engine light on and the vcds error 16785?

bought these headlights yesterday, unboxed and threw them on without checking the wires, they weren’t like your car though with the wiring sticking out, there was none on the outside and all it needed was to be plugged in

One of the most useful videos I've seen here.. maybe because I have same egr set up. Very clean engine 👍

Hi,I am planning to do the same on my car,if you don't mind how much did it cost to do complete job(your bearings and rings)

Cuestion mate what's the Soquet z sizes for the drain plug?

Late to the party here! But what difference has it made to the car since you did the egr removal 8 months on Cheers

so today i removed my egr and put a race pipe without removing the cooler is it still ok?

Gl5 😢

bro we miss your audio content

Thanks for the guide, it helped me :)

I have this engine, Always problema with starting

The problem is your injectors. You are running too much boost for this pd100 injectors. Maf n stuff doesn’t matter. Your fuel is too less

can you use them to spray stuff?

Why reflector for high beam. And projector for low...? Why not just projector for high and low?

Hello mate whwre can I get one of them radios from

You didnt cover the part where 2 6mm hex bolts and the 2 12mm nuts on the pipe from the turbo to the EGR cooler are seized up 💀😔😭

Nice vid

Price

thumbs up for the chopped lanyard!

You haven’t blocked the vacuum line by accident?

how much was the coil overs and where did you get them.

6:00 literally sounds like a fucking GTR, strap a turbo on it and call it a day

You better take synthoil 5w40 That's fully synthetic. . This oil is synthese technology

Nice video

thx mate! same thing happend to my 8P

Wanted to know if the engine light comes on after this mod?

I’m confused…is simplifying the vacuum lines and box an option to the piersberg valve or necessity? Or can I just delete the EGR and cooler and just put the pipe to the straight attatchment and then in the firewall?

Was there any damage to the rocker Arms under the cams?

your wrapping the tape the wrong way!, pleased to see it used as i've been doing it for years! but take it from a plumber - always clockwise looking at inserted end or it can unwrap when you screw in..

sell me your right side black one mate :D

Can u show the vacuum lines where does the line that went to egr go?

Do you know anywhere you can get a new muffler cover from

disconnect the maf sensor, and leave it disconnected.

Does your passat have bi-xenon? Just bought a led bar for mine and was wondering is it legit to take that signal for led bar from that solenoid cable which controls low/high beam

How to get the part piping

He stripped the door to get the housing off

Where is your bumper grill from? I love it

What could be possible if the drive is not working but reverse work.