1964 Impala SS Part 12 - Upper Trunk Deck Install - Start LH Quarter Panel Installation

Рет қаралды 12,985

Guzzi Fabrication - D.I.Y Auto Restoration

Жыл бұрын

SHOP INFORMATION :
Contact us at : guzzifabrication@yahoo.com
Our Address is: Guzzi Fabrication
3206 Main St Suite 106
Rowlett Tx 75088
Check out my other videos in our KZfaq playlist page: / @guzzifabrica. .
Honesty - Quality - Craftsmanship
What We Do : Rust / Collision Repair
Metal Fabrication - Steel - Aluminum - Stainless
Complete Chassis / Aftermarket Chassis - Front & Rear Installation
Frame Fabrication / Straightening
Drive Train ( OEM / Custom )
Wiring
HVAC
Resto Mod
4X4
Street Rod
Hot Rod
Custom
Antique Car
Speed Shop
DIY Auto Restoration
Over 20 Industry Certifications on Display:
Current AWS Welding Certs
I-Car Collision certifications
PPG Paint Certifications
OSHA - 10 Certification
NCS NESHAP Certification
EPA Compliance
Blacksmithing Certificate
Eastfield College
profile.php?...

Пікірлер: 53

@samuelsmith2522 Жыл бұрын

Glad your back making banger videos! Keep them coming

@guzzifabrication3448 Жыл бұрын

Thank you ! Yes Sir !

@glensaiz1964 2 ай бұрын

Great work this is how it should be done I've seen other people butcher these parts.

@guzzifabrication3448 2 ай бұрын

Craftsmanship, quality, and integrity job 1..... Thanks !!

@miltoncostakis799 Жыл бұрын

That mini blaster really makes a nice job of it! Nice tip!

@guzzifabrication3448 Жыл бұрын

Great news Milton, the full floor pan arrived yesterday. I will definitely be starting on the convertible mid next week, with a video the following week, I know your excited, stay tuned !!

@ST-cy6we Жыл бұрын

I like the use of the mini blaster .

@guzzifabrication3448 Жыл бұрын

Very useful, I love that thing, harbor freight may still sell them.

@mercmanwon 12 сағат бұрын

You do nice work!

@guzzifabrication3448 11 сағат бұрын

@mercmanwon Thank you sir !!!

@SmokeyA55 11 ай бұрын

This is next level craftsmanship 👍🏿💯

@guzzifabrication3448 11 ай бұрын

Thank you Sir and thank you for watching !!

@zealandianorth7383 Жыл бұрын

Good to see you’re back. I love the videos, this is one that f my favourite channels

@guzzifabrication3448 Жыл бұрын

Thank you for following the channel ! have problems with the video editior I use, hopefully it's fixed.

@zealandianorth7383 Жыл бұрын

I appreciate your hard work Robert. Your attention to detail and work methodology are inspirational. No bs

@guzzifabrication3448 Жыл бұрын

@Zealandia North That is a very generous compliment thank you very much.

@boonieg2460 Жыл бұрын

Awesome video 👍

@guzzifabrication3448 Жыл бұрын

Thanks !!!

@BIGCHIEF305 Жыл бұрын

Love these videos. Impalas are my favorites!

@guzzifabrication3448 Жыл бұрын

Thank you Mr. Marte ! I think the 63 Impala is my favorite.

@benclarke6177 Жыл бұрын

Another great video, sir! The 64 is really coming together nice!! Fantastic effort putting these videos together!

@guzzifabrication3448 Жыл бұрын

Thank you Mr. Clarke ! Wait til you see the finishout !

@benclarke6177 Жыл бұрын

@@guzzifabrication3448 can’t wait!!!

@cruzhill3411 Жыл бұрын

Love you work bro. It would be awesome to see you install a 1964 impala quarter panel for a convertible to see how you modify this quarter panel to fit the convertible since they dont make a convertible quarter panel. Thats my situation. Thanks for the great videos bro God bless

@guzzifabrication3448 Жыл бұрын

Very soon I'm starting a 63 Impala convertible replacing both quarters, stay tuned !

@cruzhill3411 Жыл бұрын

@@guzzifabrication3448 Right on my brother i cant wait bro !!! Your videos and hard work are much appreciated!!!! You have an email i can send you photos or video of my 1964 impala SS convertible? Im in albuquerque new mexico so not far away from you.

@guzzifabrication3448 Жыл бұрын

@@cruzhill3411 Sure.

@cummins724 Жыл бұрын

Another great video. Thank you. I installed a dynacorn quarter panel on my car and I did tuck it under the roof and it was a pain. You are sure right about that. I did notice that on the front corner where the roof meets the quarter, you left it flat and didn't have to lift up on the quarter. My car had the quarter come up higher right there and I replicated that. It was not easy but I noticed you didn't do that?

@guzzifabrication3448 Жыл бұрын

Good job getting it done.... that's no fun. Thanks for watching !

@cleo-wu4bo 15 күн бұрын

I did something stupid and cut the rear post to quarter seem and I really wish I didn’t. But it’s all a part of learning but he really makes it looks easier than it is. lol. I’ll eventually correct my mistake it’s metal.

@rescuedandrestoredgarage Жыл бұрын

I think that's the first time I've seen you use that sand blaster. Would that give you a bit of grief during the painting process because that looked very fast with the blaster. I have not seen your videos pop up in a while, it's starting to get nice here so the wife and I have been pulling the 262 out of the 72 chevelle getting it ready for a 350. And I am going to watch your 62 impala removal of quarters and trunk floor so we can do the right thing on our 62. Great work as usual, my brother.

@guzzifabrication3448 Жыл бұрын

Thanks for always supporting the channel !

@rescuedandrestoredgarage Жыл бұрын

@Guzzi Fabrication always, brother. Learn a lot from you.

@eikodunn 3 ай бұрын

👍🏾👍🏾👍🏾👍🏾👍🏾

@guzzifabrication3448 3 ай бұрын

Thank you Sir !

@mikeshrout7729 6 ай бұрын

Very impressive work method. I love the thorough process. Just out of curiosity, what would this amount of work cost the customer?

@guzzifabrication3448 6 ай бұрын

Thanks ! My shop rate is $70 hrs. + parts/materials

@salvadortankers6312 Жыл бұрын

Hello Robert, wonder if you have tried installing the one piece trunk floor that includes the inner and outer wheel houses?

@guzzifabrication3448 Жыл бұрын

I've seen those... kind of a new offering I don't think I would like to do that because now you're locked into wherever they set the panels and welded them together, that can be a major problem....

@miguelmaldonado9881 8 ай бұрын

GREAT STUFF. JUST 1 THING,....FILM THE CONTENT THE OTHER WAY SO WE CAN SEE A WIDE SHOT

@franciscodeleon4235 10 ай бұрын

Great Work Sir. Iv been studying your awesome work for some time now. On the rear panel were did you order from? An do they just have the lower half of the two panels? Im in search of two panels but want to make sure i get good quality panels. I may just replace the full panel. But i would like to keep as much of good original material as possible on my 64 Impala

@guzzifabrication3448 10 ай бұрын

Try Classic Industries

@chrisulloa7141 Жыл бұрын

you have any advice on a 1963 impala wheel house body mount replacement (driver side)

@guzzifabrication3448 Жыл бұрын

If you go through my playlist on 62 and 64 Impalas you may find what you're looking for. Thanks for watching

@samuelsmith2522 Жыл бұрын

Does your shop restore Impalas only?

@guzzifabrication3448 Жыл бұрын

Chevrolet, Mopar, Ford, 4x4, etc if it is metal.... I am a full service specialty / custom shop I have alot of experience with Impalas. Thanks for watching !

@robertruano1871 8 ай бұрын

Question, is there a reason why you don’t buy the whole rear section trunk wheelhouse and tub assembly?

@guzzifabrication3448 8 ай бұрын

Yes.....

@robertruano1871 8 ай бұрын

@@guzzifabrication3448 shipping cost? Or you can manipulate the fitment better welding it together in pieces…? I’m looking to do a 62 impala and it looks like it’s gonna need complete floor pan to the trunk all the way to the tail panel 🤦🏻‍♂️

@guzzifabrication3448 8 ай бұрын

@@robertruano1871 Both of those reasons, do yourself a favor and buy seperate pieces.