Old 2.3 gear reduction Starter has gone to the bad easy swap!
Пікірлер: 57
@djh22djh Жыл бұрын
I've watched close to a dozen videos and you are the only one that explained cutting the wire and attaching the new one. Thank you!
@kaplanjc15 күн бұрын
Thank you for your detailed video. Best one I saw to help me diagnose and replace my starter. Subscribed
@ChristmanGarage15 күн бұрын
Awesome, thank you!👍
@Viper-kb2bz2 жыл бұрын
Got a new starter see if I can get my ranger running again. Thanks for showing us how to do it ourselves.
@ChristmanGarage2 жыл бұрын
Thanks for the comment👍
@carolchristman21392 жыл бұрын
Daddy says unhook battery first
@Lucky_Chase2 жыл бұрын
I got a little nervous when the sparks flew !😆
@Viper-kb2bz2 жыл бұрын
@@Lucky_Chase lol made me jump both times
@joesmo5143 Жыл бұрын
Scairt the crap out of me. damn
@majordog85 Жыл бұрын
Like your sense of humor my brother and great video, got yourself a new subscriber!
@picklerix616210 ай бұрын
I just replaced the starter in a 1994 B3000. I was a little surprised that the three starter bolts were torqued on so tight. I used a short pipe on the socket wrench to get more leverage. Other than that, the starter replacement was straightforward and I did disconnect the negative battery cable before I started.
@jamesstevenson311622 күн бұрын
Also, dont forget to unhook the battery first :D
@Backwoodztuner2 жыл бұрын
Good stuff man
@ChristmanGarage2 жыл бұрын
Thanks for the comment !👍
@pokesly-az62802 жыл бұрын
Thanks...going to buy a new starter..wish me luck
@EnriqueJuarez-gf5stАй бұрын
This helped me alot thank you sir
@ChristmanGarageАй бұрын
Glad it helped
@adamhendricks7288 Жыл бұрын
Thanks, buddy! 👍
@ChristmanGarage Жыл бұрын
Awesome👍👍
@fredricabrams70817 ай бұрын
Hey you want to tell you? Thank you! I live in Olympia Washington and this definitely helped me trying to remove my friend's starter out of her truck so thank you
@ChristmanGarage7 ай бұрын
That is awesome!
@glow22158 ай бұрын
Best video ever made
@ChristmanGarage8 ай бұрын
Thanks!👍😂
@tomasperez13772 жыл бұрын
I need the wiring diagram for the ignition switch on the fire wall for the 1994 Ford ranger 2.3L
@lyndadaggers908611 ай бұрын
Did you unhook the positive cable from the battery before you started?
@GardenBoat2 жыл бұрын
So if the starter does spin but isn't engaging anything I probably have damage to my starter right? Trying to diagnose an issue I can't find online. Before failing to start, it would sometimes struggle to start and then turn over *hard* before running fine. I think my starter was misaligned, and now isn't engaging anything at all *EDIT!!!!!* You're a godsend! You mention it in the video! That ziiiiiing or whir is absolutely it thank you, you just saved me like 500 bucks
@ChristmanGarage2 жыл бұрын
Awesome! Thanks for the comment👍
@scottiegood31552 жыл бұрын
I have a 90 Ranger 4X4 with a manual transmission and a 4.0! The problem I'm having with it is that it has spun the Bendix on 4 starters in a months time. When you put the starter in and start it up it sounds as if it's metal grinding against metal. The fly wheel checks out and is good. Any idea what else could be causing this issue. I'm at my wits end with this starter. Thanks
@ChristmanGarage2 жыл бұрын
Normally these starters don’t need shims however there is a few things that I would double check first I would make sure that the block and transmission are mated properly and that the alignment shim is between them if someone has had the trans or engine out and forgot to put this back that’s probably your problem if all that is good then I would make sure I had the correct starter some of those starters look the same but have more teeth on the bendix make sure you count teeth if all else fails I have seen people mistakingly put a flywheel on backwards which will cause the exact issue you are describing. Hope this helps and thanks for the comment👍
@scottiegood31552 жыл бұрын
@@ChristmanGarage I've checked all of this and have even tried putting a shim in it. Still the same outcome
@ChristmanGarage2 жыл бұрын
@@scottiegood3155 well🤔….without actually looking at the truck I’m not sure what else to check. Has the truck ever had the engine or transmission pulled out? Did it just start doing this one day or has it been doing it since you owned the truck? If it’s making the noise you are saying something is not lined up or the starter or flywheel is bad. Wished I could be of more help 🤔 Because I was told years ago and I live by this saying that assumption is the mother of all screw ups. Don’t assume anything
@heatmyzer910 ай бұрын
Son!!!
@7.3mower Жыл бұрын
Would disconnecting both terminals fix your spark issue?
@ChristmanGarage Жыл бұрын
If I had disconnected just one of the terminals it wouldn’t have sparked I was being lazy and doing it the unsafe way👍
@courtneyM4042 Жыл бұрын
I am stuck in the dentist parking lot! Sounds like it should start but doesn’t. Should I just replace the starter? Or should I check something else first?
@ChristmanGarage Жыл бұрын
Never assume anything always check things and make sure First! 👍
@courtneyM4042 Жыл бұрын
@@ChristmanGarage finally made it home @ 1:44 am. So much testing and tinkering to do. Thanks for the reply!
@harveymanwarren1876 Жыл бұрын
Unhook the battery
@theworldofmatt3036 Жыл бұрын
So when I try and start my truck sometimes it does and sometimes I get a no crank or anything no noise but a small 1 click is that mean starter ?
@ChristmanGarage Жыл бұрын
Highly likely
@coreyreed8124 Жыл бұрын
I need help!!!!! I have replaced my alternator, starter on 1995 Ford Ranger XLt V6 5 speed. It still want crank but is turning over? What will cause it not to crank after that? Battery is good!
@ChristmanGarage Жыл бұрын
You have a fuel or spark issue. Check for spark first and if it has spark I would check if it’s got fuel pressure. If no fuel then I would start with checking all fuses and the fuel pump inertia switch is usually located behind passenger kick panel they are common for tripping unintentionally and cutting off the fuel pump. Maybe this helps👍
@EnriqueJuarez-gf5stАй бұрын
icm or cranksens
@cu.se.yko.trt5429 Жыл бұрын
Does anyone know what size bolts i can use to install my starter? Manual trans 94' Xlt 4.0l v6
@ChristmanGarage Жыл бұрын
I think they are 10x1.50 metric thread and they are usually about 1 1/2” long but they are a special application because the heads need to be 13mm to fit the starter housing
@GoT_17k2 жыл бұрын
gonna pretend I didn't see that - LOL
@ChristmanGarage2 жыл бұрын
😂👍
@richardrezzardi13636 ай бұрын
Why didn't you disconnect battery so it wouldn't be hot
@ChristmanGarage6 ай бұрын
I’m an idiot! 😂
@victorparra8113 Жыл бұрын
You should to unplug the batery first bro!!! Lol
@outlawmotorsports5992 жыл бұрын
Almost forgot… Care for some gopher?
@outlawmotorsports5992 жыл бұрын
Sikaaaaa 🐍
@ericwilkes238 Жыл бұрын
Mine only has two bolts holding it on and it's a 94 ranger
@ChristmanGarage Жыл бұрын
Yep I used to rebuild starters and they make a three ear and a two ear head and I have used a two ear on a three ear application and it worked
@jamesstevenson311622 күн бұрын
@@ChristmanGarage Yeah two is usually good enough for most things that have 3 ^_^
@akguy35tattoo Жыл бұрын
seems like for a man to claim to do, what you do,,you'd know the name of parts by now.