2014 Ford Fusion Strut Replacement

Рет қаралды 53,046

5 жыл бұрын

This video shows you how to replace a front strut on a 2014 Ford Fusion. This should work for Ford Fusions from 2013 to 2018 as the design has not changed.
My battery in my camera died about half way through but it has all the important parts on how to remove the strut and describes how to install the new one.
I purchased Monroe Struts with the coil on them form RockAuto (www.rockauto.com/en/catalog/f.... They have the best selection of most parts and are almost always cheaper than everyone else.

Пікірлер: 58

@gb342002 Жыл бұрын

I just changed my struts after work today and I've never even changed brake pads. This video gave me the confidence to do it. Thank you so much it was so easy!

@SSAK5200 Ай бұрын

For future reference that hose is for the windshield whipers you can disconnect it to remove the weather protector

@mackcurtis8319 3 жыл бұрын

Great video! I change my shocks last summer after a friend notice a distinct clinging noise which I concluded was the shocks. The sound went aways. I didn't get the best shocks, so now in paying for it because the noise has returned. I'm going to change out the struts again with quality ones this time. If the noise persist, I'll change my shocks with the help of your great video!

@bunnywaffles5295 3 жыл бұрын

Excellent video! This is also relevant for the 2013-2018 Taurus, you can add that to the title for more views. May have the tiniest differences, but TOTALLY helped me out! Thanks so much for taking the time to edit and share

@MarkTarquini 3 жыл бұрын

Thank you! I am glad I noticed toward the end of your video that you also have a Hybrid. I have 2015 Hybrid. I have done struts on a '98 Cadillac, but that was a decade ago.

@jacobmoreno6339 3 жыл бұрын

Good video! Thanks for posting 👍🏻

@josuegallegos53 5 жыл бұрын

Nice tutorial. It's sad that the camera died or it would've been a perfect video. I'm about to give this a shot myself. Wish me good luck!

@credovulae2302 2 жыл бұрын

Excellent video

@jacobbonilla1247 Ай бұрын

Doing this now... 8ne thing I always forget, to set Ebrake.

@Kadaver6 3 жыл бұрын

This is very informative. I thought replacing these struts would be way more work but this looks pretty straightforward actually.

@jarredwhite1446 3 жыл бұрын

Do you tighten the top 3 bolts last????

@patriciarodriguez2411 Жыл бұрын

I really enjoyed the video I would like to know the the exact tools I would need and do I need 2 jacks great video…

@ThePeoplesHero1 Жыл бұрын

Where do you jack it up from? Lower control arm?

@GirlsNDragons 2 жыл бұрын

So it is a different setup on the non hybrid. Learned that today, lol. Still fairly easy to do and can be done in an hour.

@betoluna7277 10 ай бұрын

How so?

@waynenation678 4 ай бұрын

You dont need to use anything to hold the head of the bolt it wont move because of how its built. Just need that 24 socket. Either use a impact, but if these bolts have never been taken out before, might want to use the socket with a power handle.

@atown7714 Жыл бұрын

Thanks for the Vid man. The only issue I had is when it come time how do you use that hammer to tap out those strut bolts for some reason mine wouldn’t budge any suggestions?

@TheDamaddog Жыл бұрын

Maybe spray some WD-40 on them for a few hours and then try it.

@jordansamuel3751 2 жыл бұрын

I am changing my struts on a 2013 and I am having trouble getting the top nut in. of the bottom two on the bottom of the strut. Any advice? I put the bottom one in first and tightened the sway bar.

@TheDamaddog 2 жыл бұрын

Are you talking about the three bolts that you need to put in from under the hood? If so the key is that you need to twist the whole strut so that they line up on top. Easiest if you use a jack to hold or have a second person. The second person is best best they can be looking on the top and try to insert the first bolt while someone else twists the strut.

@traumajock 6 ай бұрын

We had ours replaced at the same time we had the transmission out for a rebuild. That was about 3 years ago. The strut mounts are making noise again. I haven't decided if I'm doing it or paying someone. The kids are gone and my wife can't help me.

@TheDamaddog 6 ай бұрын

Well unless you are really good at things like this I would recommend finding someone to help, at least on the removing of the strut

@traumajock 6 ай бұрын

@@TheDamaddog I'm pretty good, have tools. I repaired film cameras many years ago. Cars are relatively easy in comparison. It's hand and arm strength that have diminished with age and c-spine problems.

@TJMunger 2 жыл бұрын

This video literally ended on the part that I needed to see lol. When I go to jack up the wheel assembly, it puts pressure on the pinion and looks like it's going to pop it out. Everything bows out in such a questionable way that I feel like I'm going to break something.

@joshua_luther 2 жыл бұрын

How many miles were on the original set? I have 95k on my 2014 and am probably going to replace mine in the next 6 months, along with my brakes. I'm hoping the bolts and nuts aren't rust welded on with being in Michigan. I replaced the shocks on my wife's van and had to end up taking it in to a shop for the rear shocks because I couldn't get the bolts loose.

@TheDamaddog 2 жыл бұрын

So I am also in Michigan (Ann Arbor area). I had just under 120,000 miles. Should have done earlier. They were pretty hard to break the bolts loose but I was able to do it myself.

@calebwhitefilleul7959 3 жыл бұрын

Is there a specific torque spec for the top 3 strut bolts

@Wechosworld 2 жыл бұрын

Yes 26ftlbs

@tommunds-idaho 3 жыл бұрын

John, I have a 2017 Fusion, do you suppose they are the same or similar enough? I am replacing them for popping noises. Thanks

@TheDamaddog 3 жыл бұрын

Yes it should be the same. I think even that 2020's are the same.

@bradh6185 2 жыл бұрын

I have a 2016. I am replacing the struts and tires. Is alignment necessary?

@TheDamaddog 2 жыл бұрын

So I didn't get on mine but have talked to many others that think it is a good idea.

@javisonic 5 жыл бұрын

How is the ride quality with the Monroe quick struts, I need new front suspension and I’m afraid of compromising the ride quality. Did you notice much difference? Would you recommend them?

@TheDamaddog 5 жыл бұрын

Sorry for the late reply. Yes the ride is really good. Going over pot holes and bigger bumps was terrible before and acceptable now.

@juanmsanch8 5 жыл бұрын

What's the part number for the struts are they both different part numbers?

@matthewbeck7282 5 жыл бұрын

@@juanmsanch8 Same part number both sides that is what Monroe Tech support told me . I was also confused because on the Rock Auto website some struts are shown as left and right, but from what they told me at Monroe Tech support it is the same both sides 272638 is the part for a 2013 Ford Fusion Hybrid.

@hunterm.172 Жыл бұрын

I use the same Monroe shocks, struts assembly in my make up bag, creaking when turning left, and right I think I have defective strata bearings a sound extremely dry

@jarredwhite1446 3 жыл бұрын

Do you happen to know the torque specs of the 2 main bolts (to knuckle 24mm), the sway bar bolt (18mm) and the 3 upper mount bolts (10mm)

@TheDamaddog 3 жыл бұрын

Sorry I do not.

@jarredwhite1446 3 жыл бұрын

@@TheDamaddog ok. Thank you. One more question. Is there anything specific that I need to be aware of? I ask because I’ve done both front assemblies, however, on the driver side (was the good side) is now making a popping/clicking noise when I turn the wheel. The original bad side was the passenger side but it seems to be all good. I’ve gone through it twice. What am I missing? Over torquing?

@TheDamaddog 3 жыл бұрын

Not really sure. A popping noise is different. Let me do.some research on torque and see if that could causing a problem. Did you use a torque wrench to tighten the nuts up? If so what did you torque it to?

@jarredwhite1446 3 жыл бұрын

@@TheDamaddog no I don’t have a torque wrench. The 2 main bolts from strut to knuckle I tightened really tight. Breaking them free was very difficult so I assumed they needed to be tightened way down. Same with the sway bar to upper strut. Not as tight as the lower 2 but tight non the lass.

@arthuruscg 5 жыл бұрын

FYI: The strut mounting hardware is 1 time use only.

@kingnizzy165 3 жыл бұрын

That weather thing ur talking ab is called a cowl

@DeeperSpiritualSign 11 ай бұрын

CNt see anything too dark

@mlp3journey61 5 жыл бұрын

About how long did it take?

@TheDamaddog 5 жыл бұрын

Each wheel was about an hour. Second one was faster because you already know what you are doing.

@mlp3journey61 5 жыл бұрын

@@TheDamaddog cool I'm thinking about trying it myself because the shops want 1100 just for the front smh

@TheDamaddog 5 жыл бұрын

I am not mechanically inclined and I did it pretty easy. Just follow the video. Tools are important part. Good luck

@mlp3journey61 5 жыл бұрын

@@TheDamaddog thanks alot

@mlp3journey61 5 жыл бұрын

@@TheDamaddog did you use full strut assembly??about how much per strut

@Dexion845 5 жыл бұрын

Wow Ford... just about everyone else’s strut design has studs coming out of the top of the strut but these genius’s make it harder to catch the top by using bolts instead of stud/nuts 😓

@GirlsNDragons 2 жыл бұрын

On the hybrid yes. On the regular fusion, it’s studs. Not sure why they changed it.

@joeshafer881 2 жыл бұрын

Im there right now gonna install my own studs and use nuts the bolts through the top miss one thread and your screwed