Those who are asking for the torque charts. This information is found on the workshop service manual. Bentley Publishers used to do a good and very thorough version. Im sure this information is available within BMW ISTA D P now top
@zandas765 жыл бұрын
thanks for all the hard work keep it up ...nice rebuild
@stephenmercado36735 жыл бұрын
those crankshaft bolts are a pain in the butt..I'm a BMW tech at the dealership and me and the guys have went out and all bought ourselves a 6ft adjustable ratchet that has a inch snout to avoid all breaking our torque wrenches and snappon wratchets
@SanDoval2019704 жыл бұрын
the manual clearly says used a 3/4 drive socket whit a breaker bar to do the 360
@hevendranarayansamy27934 жыл бұрын
This some high torque. Nice work
@muckman55092 жыл бұрын
what cleaning process do you use? Chem bath?
@ligend73 жыл бұрын
Thanks 🙏🏻 broo
@i9907493 жыл бұрын
Hello Tasos, which oil would you advise for n63 engine in Europe? The engines run at relatively high temperature 105-110. Would 10w60 be a good choice? Greetings
@armirhoti38133 жыл бұрын
Hello mate thanks for your vidio Where can i get timing tool this engine or if you have any part number? Thanks
@stripping-santa2 жыл бұрын
Hi my S63 looks like it has a crack in the cylinder wall and it’s seized. Can a new sleeved put in just one with a new piston?
@jasonwhite81452 жыл бұрын
Hello. Just rebuilt my n63 2011 550i gt and now it will not start. Codes reference all 4 cams out of limit. Crankshaft sensor seems good, i tested voltage and signal using a socket to make it read. I purchased a crankshaft kit with bearings snd am thinking i have the wrong crankshaft now. Is that possible? I have checked timing several times and it seems fine. All 4 cams align perfectly with the locking plates installed and cranshaft tool installed aligned with timing marks on balancer. Flywheel aligns with the dowel pin on crankshaft. Any suggestions?
@aragrox3 ай бұрын
Whats cross hatching angle for piston rings?
@andrewdarakis88074 ай бұрын
Why not use a 1/2 inch breaker bar or even 3/4.
@arthurmkheyan64876 жыл бұрын
Hello Tasos. By your opinion whay N63, S63 Bmw engines burn excessive amount of oil. I had 2012 Bmw 750li with N63 engine now i have 2014 Bmw B7. My friend has 2015 Bmw M6 with N63 engine. All of them are the same thing you need to add 2liter oil every 2-3 thousand miles. Thank you
@umbrellasolutionstech3 жыл бұрын
can i purchase a teardown and assembly instruction from you?
@mattiel91566 жыл бұрын
Tasos, what cleaning solution do yoy use for cleaning engine parts? Thanks
@Bemaritohtori4 жыл бұрын
He told that he uses: REPSOL Moto Cleaner in one video👍🏻
@TheRealAnthony_real6 жыл бұрын
@Tasos where did you get the torque numbers list from ? Thanks
@buguno11 Жыл бұрын
Did you get the answer?
@mbgtcentre92915 жыл бұрын
you heat with the solder the tool that why this brokes :) its ok about this dumper pully its not the end of the world never go out if you put just 100nm and 90o
@markosthomadakis9256 Жыл бұрын
Το καλύτερο μοτέρ όλων των εποχών ρε
@frederickhalljr89472 жыл бұрын
HI COULD YOU REBUILD MY X5M E70 S63? THANKS
@ivanmamedov905 жыл бұрын
Is that stock bmw pistons?
@TasosMoschatos5 жыл бұрын
ivan mamedov hi, yes these are the stock pistons.
@alexbeli27245 жыл бұрын
How many km have the car???
@TasosMoschatos5 жыл бұрын
Alex Beli 78,000km
@nasser-nasab4 жыл бұрын
Anyone can help with Bmw s63 Tightening torque chart? How to get one?
@jonathanlinehan9316 Жыл бұрын
Did you ever find one?? I'd also like to know
@jayl8813 Жыл бұрын
Me too Torque spec on rod bearing.
@austinraney6460 Жыл бұрын
why show us how to rebuild this if your not going to show us the most important part "torquing the crankshaft and how to set the outter cap screws"
@TasosMoschatos Жыл бұрын
It's just for the customer, if it was on my hand it will be unlisted.
@almasa105 жыл бұрын
you need big handle boss
@Khaledghaffari3 жыл бұрын
The price of the car cost the engine😂
@TasosMoschatos3 жыл бұрын
It didn't cost even the 1/3rd of the price of the car. How much you think is the price of an M5 2015 with 60k km only back in 2018?
@Khaledghaffari3 жыл бұрын
@@TasosMoschatos all bmw parts company in gulf is expensive 2015 m maybe 🤔 30.000 usd in Dubai I don’t know
@TasosMoschatos3 жыл бұрын
The spare parts back in 2018 cost 18k aed
@TasosMoschatos3 жыл бұрын
Today a used M5 costs 130k aed
@Khaledghaffari3 жыл бұрын
@@TasosMoschatos wow not bad . 👍 Spare parts are expensive in Kuwait. And less people run this engine.
@stephenmercado36735 жыл бұрын
you should have replaces all timing components while engines apart...s63 have valvetronic hear issues along with guide wear
@TasosMoschatos5 жыл бұрын
Stephen Mercado hi, the engine was have 60k km, it doesn't make any sense to change anything of the timing components. The engine currently have 80k + km and 650 whp. Thanks
@mbgtcentre92915 жыл бұрын
its look like bmw v8 biturbo motos its look like shit:) this motor not the solid conception of m156 m159