Fantastic, I've been struggling with my controller & finding a video for the same controller as yourself, life saver, thanks :-)

Thanks for this info. I thought I was going mad as I couldn't make head nor tail of other you tube vids. This has been a life saver.

Great advice.. I needed this, got too much heat at program 1 in the Night.

finally, this is my model and doesnt match most tutorials. Finally on the same page and hope this shares all the functions.

Awesome. The instructions aren’t able to be followed by what they give you. Good man

Just what i was looking for. Thanks 🎉

This model of controller has all of the "secret" menu items deleted, you cannot access them by typing in a code like you could the previous model. All it has is Temp control, On/Off, Timer and that's it! With the previous model you could alter the fan speed, link to you phone and Afterburner app, pump pulse rate and voltage range. If you want the earlier style control LCD, you also have to change the ECU board too as they are different protocols for controlling the heater. The 'older' style LCD has the WiFi symbol at the top of the display, the newer one does not.

Thank you - perfectly made and judged vid👍

Brilliant!.. couldn't find the instructions for the controller anywhere.

The setting you were not sure about is the number of hours you can set the heater to run, great video, we have this one

I have this control on the 3rd 5KW all-in-one (red slim case) I bought in January 2023 from VEVOR. The two physically identical heaters I bought before in 2021 and 2022 had what was called "new Blue-style controller" with the elapsed- time. I do not like this control - NOT because it's in any way difficult to use, but because it connects to completely differently-programmed controller! This controller start-up routine idles the fan super low, and turns on the glow plug. When the plug reaches temp, it does a fan pulse with 3-shoots of fuel from the pump and then drops the fan speed back again. Then starts pumping the normal H3 pump rate before gradually increasing the fan speed to a high rate. This results in too much fuel and white smoke during start up and a fuel smell escaping from the air intake for about 5-10 seconds - until the flame in the burner can be heard noticeably increased and the glow plug goes out. After that, the fan comes up to a mid-range blowing lukewarm air until it reaches operating temp at H3 by default and the blower settles in. At shutdown the glowplug comes back on and the fan is slowed to almost stop - running at idle for about a minute or so - apparently with the idea of allowing the additional the burner chamber to burn off more unburned fuel residue. Then after hearing the exhaust pipe ticking from the heat, the fan finally comes back up to a useable speed to complete the cooldown. The identical unit with the earlier "New Blue Controller" did not attempt to reach near overheat conditions by virtually shutting off the fan on an already hot burner chamber with a lit glowplug. Instead it turned the glowplug on with the blower going immediately to a high speed until cooldown was completed. During startup, the fan ran at a slow but still functional CFM while the glowplug was on. On reaching ignition temperature the pump was started at a high rate, the fuel ignited and the fan speed was increased to force more air through the chamber. The result was no exhaust backflow and faster operating temperature air discharged from the outlet. I do not prefer this new style controller at all. However, it is both the controller and controlboard (and possibly the harness wiring) that would have to be retrofit to convert it to the timer-type Blue controller. (Unfortunately this same controller format with "H3" on the display is also being sold in the original blue controller shell! It is not to be confused with the black or blue "00:00" ones!) The start-up and shutdown procedures programmed into this "H3" controller do not compare favorably against the "00:00". This was not an improvement.

The screen you're not sure about is for programming remote control thank you for you're help

YAY I finally found someone else that has the same controller as mine ! Mine has that circle with the negative sign in the middle and my Settings button doesn't do Squat ! Mine came without any instructions too ! ALPINE Mode...I just learned what the hell that icon was ! My lowest Pulse rate was about 120 beats per minute before...with the Alpine mode it is down to about 80 beats per minute...Perfect ! Liked/Subscribed !

So glad I found this video this controller has been a pain to figure out!

I've just got a couple of these heaters. Like you, I haven't got a clue how to set the timer. The "Chinglish" instructions are almost useless. One thing I have found, is to prime the diesel pump, press and hold the up and down buttons at the same time, and the pump will start priming. It does however need you to hold the buttons or it cuts out. Not ideal if you're trying to prime your new install on your own. If you or anyone gets any more info on this controller, please post it here, I'd love to know. Overall though, I'm impressed. It's warmed the space we have it in very quickly, and really didn't burn that much fuel. Thanks for the video. 👍

Activating the Timer Start/Stop function Press Settings and decrease buttons at the same time for 2 seconds. Timer active indicator will turn on (clock face) If activated while unit is shut down, this will schedule a start operation, and ON will flash next to the timer icon. If activated while unit is running, this will schedule a stop operation, and OFF will flash next to the timer icon. At any time while the timer function is active press the settings button to see the remaining time to ON or OFF. Setting the Timer Delay Press OK and Decrease buttons at the same time for 2 seconds. Timer active indicator will flash. Press On/Offbutton to select the digits to adjust. Use the increase and decrease buttons to adjust time delay up to 24 hours. Press the OK button to save the settings and exit the interface .. or press the Settings button to exit without saving.

I lost my booklet and am having trouble finding info on this particular model. I do remember that if you hold up and down arrows at the same time it activates the pump to prime system.

Thanks, saved me

Thank you 👍

For initial priming of fuel - hold in up and down buttons at the same time for 2 sec.

Thank you

Yes my controller is the same. I think this comes with the variable heat heater. Like you said it isn't as common as the other style controller. Any how you showed how the Plateau works. It is dropping the heat down which is great. I also think the Celsius reading isn't 126deg but 26. You just leave the number 1 Off. Cheers.

I have the same controller, couldn't work much out but before I knew it diesel was going though line & warm air was coming out,im talking about 1min.is this to quick?.also the exhaust pipe was bloody hot to hot to touch,

Might that last setting be a timer to off that you can set??

I have this unit too. It worked great for about 3 months, just broke today. Still checking it through. The controller went black. I checked all the electrical wires and connections, all checks ok. If only I could catch somebody on their phone number, maybe have a better idea what broke.

Real life learning. I'm three years, and two generations into these things.

How low does the internal temperature drop too when in the H1 setting? I saw you set the temp down to 15C does it drop down and maintain the temp at 15C.

Hi, can you please advise me? How to switch to 24V voltage? The old model was PIN 1688. I don't know how to get to the service menu.

Can you just swap this out with the more common style or is it matched in some way with the main board in the heater itself. ?

I just got one of these about a week ago and it’s a near identical controller but it had a fuel pump prime button between the ok and settings button on the left

When in the auto mode, and I set it to a temp, will it automatically adjust fan speed AND fuel rate? If I set the temp to one lower than ambient, will the fan just run on its own?

FINALLY

Do you happen to know what the function does when you hold the down button and power at same time?

i have this also,could not get it to prime ,so i just hit the start on and it did start! the two blinking lights that indicate air in exhaust out , only the air in is working ! i could also not get any response from display! is the display bad or the isu?

I have the same heater and couldn't figure out the controls. No instructions. . Works great thou

That's the timer you can get it to shut off or turn on

I need this model of controller. Where to get it? The other model shows e-7, wrong controller. Need same as you have.

Thanks, just bought one and it looks like my controller is like this. I haven't set it up yet so it will be interesting to see what it looks like. my instructions show a screen like yours.

I installed a heater recently with this controller. It came with some limited instructions. Including how to set the countdown timer for on and off. Anyone interested in photocopy of that?

great video can you tell me where to buy an extra lcd controller for back up purposes.like this one.

Are there any updates on this LCD controllers functions? Just installed mine yesterday.

Anyone found a way to change hrz and enter hidden menu on this "new" model ?

Did you ever find instructions. Mine came with some.

I think the code is 168 after pressing ok and on together . Heater 5 to 8 kw heater should be set to 7hz and fan at 5000 rpm from doing some research .

Hi. Thanks, finally found the controller that was shipped with my unit. I like this one, simple and easy to use. Do you know how interchangeable these controllers are as my portable unit with 4 heating ports is not doing what I need. Cheers.Jim.

I also have this controller, figured out most of the settings, I am looking for how to get into the deeper menus/setting, I want to adjust the pulse rate and or the Fan Speed to lean this thing out, ( no soot buildup i can tell). On regular mode it easily gets to 206 C and plateau mode (aka high Altitude reducing fuel for lower oxygen content in higher altitudes) it runs about 145-155 C. I know either speeding up the fan (for greater cooling and more air into the combustor) or lowering the pulse rate to reduce fuel will bring that 206 C down to a manageable rate say 176-189 C. Any one know anything more about this style of controller? Thanks in advance if someone does ,

I got one summer to that but do not know how to pair the remote to it do you no thank you

I have this controller and I need to tell it 12v how do I h do that .

I've just installed the same model. I wish the controller was like the old style. I tried hooking up an older style controller but it just gave an error code E-07. Incompatible it seems :(

I have same model. I had installed in a service in Romania, but now I am in Holland and mine is not stop on automatic mode . I had set it on 20 grade and he heat up the car till 40 and still not stop. Maybe is a problem with temperature sensor. Do you have same problem? He go on lever 1 and still bring heating but not stop totally.

Best explanation ever. Cheers luv, from 🇦🇺. I started mine up before seeing vids, and when it was getting to 160 plus Celsius I was scared and shut it down. Now I know , that’s the heat of the heater. So I will try set my room temp , and take it from there. These LCD screens that come with d/heater, are set to 12volt already I believe. I think 🤔 u can adjust the volts, … works beautifully, just concerned with the exhaust, the amount of heat it has. I have wrapped it with exhaust wrap, so I don’t know maybe with the smell due to 1st time use. Can u help me with this. Is this normal.?cheers

Does your unit mounting plate get quite hot during operation?

My heater does not stop when it gets to set temperature. For example: 1) Trailer is at 14C 2) I set temperature to 20C. Heater turns on and heats 3) Trailer reaches 20C. Heater goes to minimum setting but does NOT stop 4) Trailer temperature keeps rising to 25C+, very uncomfortable. How can we have the heater turn off or run fan alone when reach desired temperature?

The Alpine or plateau setting is for when you are using the unit at high altitudes. I don't believe you should use it at lower altitudes as it's an incorrect fuel air ratio. Alpine and plateau are just terrible Chinese translations for " high altitude "

Im trying to find an icon guide for these.

To adjust the temperature, just open a window. If it still gets hot, open another window...

Someone mentioned this controller is the old style but I think these are the new type ? Any answers ?

I want to buy one of the other style that looks exactly like this one...but how will I know what one to order? I don't want another one like this one !

I have this controller but when I turn it on it doesn’t display the 12 v. It has 3 dashes where the 12v should be displayed

hi what are the codes? because I see you entered 125 and it warms less

How do you pair the remote to this style? SOS

Hi there I have the same diesel heater controller, Do you know how to prime the pump? Thanks Russell

Any updates on this controller? the hidden password protected settings in particular?

any ideas how to use the remote that comes with it?

Helo, how to set the machine to turn off at a certain temperature? Thanks

great video ugly topper,i have the same problem with my new heater the lcd screen is different. and i have no idea how to prime,set temp,and the hzh mode.can i buy one of the other lcd moniter screen and plug it in will that fix the problem.if not can you make a video showing how to set all of the functions on this one thanks alot i was about to give up on this little heater before it even run.

Does anyone here understand how to select between 12V and 24V on this controller manually? Or is it not possible and auto select is the only preference available?

Please, please tell me how to pair temote on this kind o controller.... Clasic eays dont work!!!! Pleaseeee cant find any tutorual that works!

Can you turn the controller led off?

i have this unit bugger all out there on it, anyone have a manual (that was not the one it came with it)

I got this heater. Mine seems to go through fuel faster than I thought it would. I can’t figure out how to prime my pump nor set the clock or anything else. Psh

just wired up same controller, all lights up but displays no error just circle negative symbol and 3 dashes no numbers & will no turn on HELP!! liked and subscribed , buttons do not seem to operate

Has anyone been able to workout the password for advance setting to get past the three 000? Is there an advance menu for this model that can be accessed?

Has anyone found if there are advance settings ,if so what is the pin .TIA

Has anyone confirmed a 3 digit password?

Does anyone know how to set the temperature with this controller? Mine seems to increase as the heater runs.

Has anyone figured out how to pair the remote to this style controller?

i tried today to pair with my remote but no luck. Wrote to the seller to provide some info.

How do u set time on this lcd display

I have four different kinds. there's not 2 the same even if they look the same

Thank you, there is more info here - kzfaq.info/get/bejne/fN6qiK6ZqcuteWQ.html

Thanks for your attempt to decipher BUT you only got part of it right and should note that the instructions I recieved with my heater recieved a month ago warn NOT to use the "Alpine setting often" its referred to as Plateau setting. It says that you can damage the system .......... no idea why???? They seem to be good little heaters for the $ but the support side is abysmal especially the instructions ....................... your better without. This controller we have is obvioulsy the cheap one as my friend purchased a different style same $ range but has a controller that is far more intuitive with better options and settings. You get what you get when you go Chinese. Really too bad when they have what appears to be a great product but extremely disappointing support.

I finally got a replacement Display/Controller unit for my Diesel Air Heater... It came with the E 07 Error Code and only Beeps when hooked up to my heater....my old controller still works, I just wanted the one that I could program. So, I got the Seller to send me a Replacement Controller/Display unit. It has the E 07 Error Code too and only Beeps. I ordered another Complete Chinese Diesel Air Heater too.... It came with a Display/Controller with the E 07 Error Code and only Beeps ! I have a total of 2 Chinese Diesel Air Heaters, 6 Display/Controllers and only 1 complete Unit that works ! *HOW THE F DO THESE PEOPLE STAY IN BUSINESS ?*

Has anyone confirmed a 3 digit password for advanced settings?

Ur drivers license pic looks like a thumb

Sausage fingers