Ferguson 23C Diesel Engine Part 4 Removing the Cylinder Head

Рет қаралды 8,016

2 жыл бұрын

I run through what I like to look at when removing the cylinder head from an engine.
Please support our channel by purchasing merchandise here: bundybearsshed.com/
Hello I'm Lance (aka Bundy Bear) and doing these videos is my hobby. I do own Queensland Tractor Spares in Australia where I sell parts and offer technical advise to customers.
Parts seen in our videos can be purchased from www.queenslandtractorspares.co...
We have a lot more than we can offer on our web site available to us and in our store. If you don't see what you would like please email info@queenslandtractorspares.com.au and we will help where we can.
I do try and help with technical advise at bundybearsshed@gmail.com if you have a question or are having trouble with your project.

Пікірлер: 26

@v8man350 2 жыл бұрын

Fantastic videos, thanks for sharing your knowledge 👍🏻

@BundyBearsShed 2 жыл бұрын

My pleasure!

@TheKnacklersWorkshop 2 жыл бұрын

Good video Lance... I've enjoyed parts 1 to 4. looking forward to more in the future...

@BundyBearsShed 2 жыл бұрын

Awesome, thank you!

@ianahmet9286 2 жыл бұрын

Good one Lance I’ve enjoyed watching the 23c series, you make interesting ,thanks

@BundyBearsShed 2 жыл бұрын

Cool, thanks

@charleshart6992 2 жыл бұрын

Great stuff!

@BundyBearsShed 2 жыл бұрын

Glad you enjoyed it

@andrewcollier755 2 жыл бұрын

Thanks Lance. Interesting about the head bolt stretch and thanks for the bolt strength info. Reminds me that some of my head studs were corroded- made them noticeably thinner and therefore had to be replaced.

@BundyBearsShed 2 жыл бұрын

Yes this is often overlooked I believe.

@manfromthemist1958 2 жыл бұрын

experience always show, brill video's mate

@BundyBearsShed 2 жыл бұрын

Thankyou.

@Rolf2014 2 жыл бұрын

Yes great, the head looks great.

@BundyBearsShed 2 жыл бұрын

Yes it does for sure.

@17volcanic 2 жыл бұрын

Good stuff

@BundyBearsShed 2 жыл бұрын

Glad you enjoyed

@bjrn-steinarhanssen2102 Жыл бұрын

My father told me to compare the headbolts tread towards eachother. Hold one hed down, and the other head up. If there was a difference in tread, it would show up easily. Bjorn from North Norway.

@BundyBearsShed Жыл бұрын

Yes that would be good advice I would think.

@jamielawson1534 2 жыл бұрын

Great video series on the Ferguson 23C, getting ready to restore a Ferguson TE 20. Have you ever done a video on the Massey Ferguson hydraulics? Can't find anyone who knows how to add rear remotes to the MF 175.

@BundyBearsShed 2 жыл бұрын

Not yet!

@Kake84 Жыл бұрын

That engine looking so good condition. I bought new head bolt set and there is two extra bolts 132mm. Do you know what is idea for those? Set have nine 125mm bolts so i can use those. Repairing my MF35 23C engine and cylinders no big wear but one liner cracked and one broken head bolt. So i put new liner, piston, rings and bearings. Kake84 Finland

@BundyBearsShed Жыл бұрын

Im not sure what they would be for, have a good look and make sure you are not missing something. check my video on the secret tubes in the 23C head, it may save you some drama later.

@andygough4666 2 жыл бұрын

looks too good an engine to scrap be worth it weight in gold over here in the uk

@BundyBearsShed 2 жыл бұрын

Good to have a few spares around, wait until you see the pistons and liners!

@garethdavies3220 2 жыл бұрын

Hi Lance, as you were struggling to lift off the cylinder head I thought an easier way may have been to rotate the engine on the stand 90 degrees and pull it off sideways . Cheers .

@BundyBearsShed 2 жыл бұрын

Funny you may say that, when editing I was thinking the same thing, lol.