Fixing A Toro 2 Cycle Snowblower that Won't Run or Start

Рет қаралды 95,611

4 жыл бұрын

amzn.to/33aeJhn Suzuki Carburetor Replacement
amzn.to/34omHDx Ultrasonic Cleaner
amzn.to/2oEiAUI Snowblower Scraper Bar
amzn.to/2C3T26A Toro Rubber Paddle Replacement
amzn.to/2C7wYba Toro 2 Cycle Oil
In this video, I take you through the long process of cleaning the carburetor on a Toro ccr 200e
Help support Doublewide6 Repairs LLC by sponsoring his Patreon account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.

Пікірлер: 70

@doublewide6 4 жыл бұрын

amzn.to/33aeJhn

@dubwiseselecta1 4 жыл бұрын

At our shop we never take the top cover off to repair the carburetor. If you take off the black panel and remove the two screws on the handle you can pull the bottom cover out without taking off the top and it's a little less work but I understand doing it for the video to show everything.

@tomlewis3658 4 жыл бұрын

In the 90's, my father had 1 of these, with a Tecumseh 2-stroke engine. One time, when I was reassembling the covers after cleaning the carb, the rod for the choke attachment slipped off & I missed it, so fully assemble the covers, then disassemble them and this time, make sure the choke connection was correct and reassemble the covers again. Around 2004, I placed an ad and sold it locally, and I had several replies. A lot of people wanted it - they knew it did a pretty decent job for a single-stage small unit.

@kentpajor6241 2 жыл бұрын

I worked for a hardware 1985 to 1990 the CCR 200 is a Suzuki engine.

@megaloogy 4 жыл бұрын

I've worked on a few of these, Almost always a carb issue if they don't run. Good video.

@trotptkabasnbi6655 Жыл бұрын

I’ve found primer bulb placement much easier if positioned on the metal frame first and finish up mounting the plastic cover

@rbarr775 4 жыл бұрын

I became a convert to the light 2-stroke machines several years ago. I have a Honda HR621, but I use this thing's little brother, the Powerlite 1000, for most Chicago snowfalls because it's light and always seems to 'punch above its weight class'. Choice of premix oil seems to have a major effect, and I've never seen a machine that handles wet, slushy snow clog-free better than the Toro Powerlite.

@maybacher

You can pull out the rod crank for the chute allowing you to take off the top cover so there's less plastic in the way

@theoldbigmoose 2 жыл бұрын

Your video helped me a bunch. Brought the son in laws home to repair before winter. Left old gas in and won't start.... so carb time!

@ektalon1 2 жыл бұрын

I appreciate your attention to detail and showing it with close-up camera work.

@jerdebson 4 жыл бұрын

I've had one of those for over 30 years. The dealer said it had a Suzuki GTS (Guaranteed To Start)(in two pulls, which it did for years before the primer started to act up) 2 stroke motor. It is a great unit. Mine isn't an electric start, but wish it was. I prefer to use it over my 28" S.P. unit, if the snow isn't too deep.

@samtate1260 3 жыл бұрын

Those plastic covers are a pain aways rusted from salt they never put stainless steel screws and bolts found one in the garbage was locked up got it running but needs the carburetor cleaned good video

@TorBoy9 Жыл бұрын

Nice carb teardown and clean. Very well detailed explanation, thanks! It sounds just like mine!

@googleusergp 4 жыл бұрын

It's a Suzuki 4.5HP engine. I just picked one up today from someone off FB Marketplace for free, model #38185. An aftermarket carburetor runs about $10-$11 on Ebay, that's the way I'm going for now.

@donnagavin4539 Жыл бұрын

The panels are a pain in the you know what! But your video was perfect! TY

@rverro8478 4 жыл бұрын

Not exactly my first choice for a snowblower but, I like the fact that it needs premix fuel. You can run them at a high degree of inclination and the engine will never suffer from oil starvation. I'd like to get my hands on an old 2 cycle lawn-boy push-mower though.

@MisterBigDave 3 жыл бұрын

Great video, I have to do one of these before the winter. Like brand new, just doesn’t run. I’m sure it will go fine but what a freakin PITA. .

@nashguy207 4 жыл бұрын

Good Job Bob. I have never ran into a suzuki 2 stroke engine or carburetor down here but we dont have any snowblowers down here either. LOL The carb looked similar to a Honda carb to me didn't look to difficult to work on. Hope the son and the rest of the family is doing well. Have a great weekend buddy. God Bless!!!

@ronfirnrohr749 3 жыл бұрын

I replaced the carb on mine but you are right, the struggle is to get that thing back together. I saw you had removed the top cover and although it took about 10 minutes to remove it all, it saved me another hour and a litany of 4 letter words trying to get the bottom piece on. Also, by removing the top you can access the wires for the switch and ensure the choke lever is seated correctly and ensure the primer hose is still connected.