Replace the drawstring with some blue 10mm rope. Then use a Chinese finger trap on the cable end and tie the 10mm on. It doesn't hurt to lube the cable if it's a long run as well.

Thanks so much for all your help on this job, enjoy my time working with you and can see a bright future ahead for us both ! 🎉

Just for the kids out there. The two 5.pole breakers are in parallel not series. I hope they are linked so as a fault trips both or that could have big consequences. I'm sure it could have been mechanically linked with a channel over the two arms. But as it's a custom made unit I'm sure it's all been properly designed.

You,ve got one of those screwdriver shaped hammers , as well 😅

Good video to watch Nicholas. Personally, I would have pulled a blue poly rope through with the cable (8'10") for possible future needs, such as Cat 6. When you used the step/ cone cutter on the alloy (9'50"), I would have sprayed the bare alloy with black paint to protect it, and (12'40") it is good to get a preview of the new Knipex electricians light duty, rubberised hammer. .. 😂😂 A nice looking install at the end of the day though, good one.

And today Nick learned that, when following ground workers on to site, you ALWAYS leave time for fixing their work for them.

Here's me thinking DeWalt would be right up your street with it being the batman logo colours 🦇

Because they laid it on a friday afternoon and thought bllcks to cutting the duct at every pit! Screw the sparks as always!!

12:50 weird looking hammer 😂 Proper tidy looking job, though!! Good luck on a Doncaster Cables tour 🤞

I was on a job a few years back where the groundworkers installed ducting a metre deep but a bit like yours did it completely wrong. They ran a duct around the site but only put one tube to the access point and taped it to the underground pipe with tape. It took us ages to fish out the rope they installed but it was made more difficult by the two feet of water in the duct due to them using field drain pipe instead of actual ducting plus the taped joints.

My god Nick is now mining for flex conduit now!

The van you head is called the "BapVan" I used to work for a company on that estate that ironically do ev chargers

I can confirm leaving your van open in and around Doncaster is a terrible idea 😂😂 especially with the Milwaukee kit

Nice work chaps, love a good commercial job.

Experienced many situations of contractors doing whatever is easiest for themselves and screw it if it makes things more difficult for anyone else😂

Brilliant video ❤..good to have a change 👍

Another cracking video Nick keep them coming! 👏🏻👏🏻🔥🔥

You should create a line of Telly-Tubby dolls as the Bundy Groupies.

Thought the estate looked familiar but the batman Sandwich van was the last clue in the jigsaw puzzle

Well took me to watch until the very end for you to say about a visit to Doncaster cables for me to find out you are defo not in Bristol! 😂😂😂

Are all those chargers going to be on a radial or a ring circuit, with all the potential current draw?

Make sure to power the Easee units and get the firmware updated first. I spent a long time thinking my Easee was screwed because the Megger EV tester kept on producing PE Errors and wouldn't test. After the Firmware update and reboot it was perfect.

Must be Bristol if you got the bap mobile flying around!! 😂😂

Nice video - enjoyed 100%, thanks Nick. Loving the AI comments about 'camaradarie' and 'wealth of wisdom' - totally right of course...

You sure about that current rating chaps 122amps? What temperature are you running it at and what rating factors applied?

What is it with trades not thinking about what others have to do afterwards ?

EV uptake through company schemes are always a good idea ... But some people can't do the Maths .... keep up the good work Nick ... it's all good money, Adams Mum sends her love.

Should never trust that pull cord (it snaps(a lot!)). Always replace with bt cord mate.

How did you end up working in Doncaster? My home turf. The bap van actually calls at our depot!

That's only tiny tiny breaker. Come back when you can climb inside one.

using a cable sock would make the job easier just a thought pulling the cable through the ducting.

Maybe don't put the bollard on the lid tho??

Which Easee chargers are they? Sure the Easee one has PEN fault protection built in?

Always Great Work 🧐🙂🇮🇪☘️

All sites ruin the ducts without fail there will always been 1 collapsed or filled with mud 😢

by opening those mounting holes on the pillar, he just voided the warranty on it...

At 16:19, what's the matter with the apparently switched PE? Why is that even legal to do?

nice big dark oriffice nick!

Almost missed the cameos from Margot Robbie and Megan Fox!

Looks like you're enjoying doing something different.

you've corrupted me, as soon as you dark orrifice, I immediately jumped to thinking Adam's mum

Or is this the Birmingham branch?

lol!!

Clown Shoes !

What I don’t get is we all installing the odd charger at work but juts look how many cars are in that car park......this is so stupid it can’t be the future

Why not specify a charge point that has the built in fault protection? Does anyone else get annoyed when they are called chargers!?

Hope your up to date with you vaccines using dewalt stuff

First