How To Install LED Resistors - Everything You Need To Know | Headlight Revolution
Рет қаралды 826,431
Күн бұрынPricing and details on the GTR Lighting Resistors: www.headlightrevolution.com/5...
When installing LED bulbs to replace your factory blinker bulbs, you will have a "fast flash" or "hyper flash" problem. This means the vehicle will think you have a light bulb burnt out and, as an indicator to you, will flash quicker than normal. In this video, Chris shows you everything you need to know about installing resistors and shows the best practices and tools to make the job easy.
/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/
Installing these resistors will fool your vehicle into thinking it has a light bulb in good condition installed and will blink normally. Simply wire the resistor between the ground wire and the blinking positive wire.
Find The Best And Brightest Lighting Options For Your Application Here: www.headlightrevolution.com/?...
/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/
Fitment guaranteed! If it doesn’t work, we will solve the problem for you. We strive to give an excellent customer service experience. Our dedication to delivering on that promise is backed by a no-hassle return policy. We’ll provide a full refund on products returned within 30 days, no questions asked.
Other videos that we recommend watching:
💡 Lighting Color Explained: • HID Color Temperature ...
💡 Are LED Bulbs Brighter than Halogen? • 100W Halogen VS LED Bu...
💡 Are LED Bulbs Brighter than HID? • HID vs LED - Which is ...
💡 LED Bulbs Brightness Shootout - which bulb is the brightest? • Best and Brightest? We...
💡 Which HID Kit Color is the brightest? • Which HID Color is the...
💡 The TRUTH about LED Bulbs! • The Truth about LED bu...
/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/
For the best LED automotive lighting selection in the world, check us out here: headlightrevolution.com
If you have any questions about any of our products, email us at Sales@HeadlightRevolution or give us a call at (218) 755-5200!
/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/-*/
Find us on social media!
TikTok: / headlight_revolution
Facebook: / headlightrevolution
Instagram: / headlightrevolution
Pinterest: / headlightrevolution
Twitter: / headlightrevolu
LinkedIn: / headlight-revolution
We Do Lighting Better Because We Test!
@kipdodd9851 4 жыл бұрын
Dude is better than most I see on tv, easy to follow and speaks well. Keep up the good work Bud!
@HeadlightRevolution 4 жыл бұрын
Thank you!
@billmaggiewatson6722 Ай бұрын
@@HeadlightRevolution8:29 8:33
@Phil_Trujeque 5 жыл бұрын
*Pro Tip* If you wanna avoid ripping part of the sleeve off to test a wire... take a safety pin or a sewing needle, and jam it into the wire you wish to test, then hit the pin/needle with the tester... *Bam!* no broken sleeves!
@HeadlightRevolution 5 жыл бұрын
Great advice!
@flyurway 3 жыл бұрын
That's horrible advice!! Never poke a wire unless you're sure you're going to cut it anyway. Once you put a pinhole in that wire you've sealed its fate, it will eventually turn green. It's just a matter of time and there's no stopping it.
@HillBilly-1 2 жыл бұрын
If you probe wires just seal with liquid electric tape
@nicholaswalker5555 2 жыл бұрын
@@HillBilly-1 i do that all the time never had a wire fail. I usually liquid tape and heat shrink my soldered connections never had one green
@elhefee2825 Жыл бұрын
I would like to know do you have to have a resistor for LED lights on your turn signals if you're doing 1930 through 1970 0 year vehicles thank you
@eaz54 3 жыл бұрын
Thank you for explaining the process of identifying the correct wire. So many other "how to" videos just skip that part by saying they already looked it up before hand and they're just gonna start connecting stuff. There is no assumption in a how to video, other than assuming we're a blank slate and we're watching the video to figure out how to get started.
@HeadlightRevolution 3 жыл бұрын
Glad it was helpful, thanks for your feedback.
@adenramirez870 Жыл бұрын
Thank you so much for the step by step instructions. I had replaced my front turn signals with LEDs and it had the hyper flash. I known and heard about this being an issue for others and you helped me figure it out. Stopped by my local autozone and picked up a multimeter and resisters and put em in same day. Thanks man!
@HeadlightRevolution Жыл бұрын
You're welcome!
@Steve-oh9tu 4 жыл бұрын
Resistor goes to ground! Who would of thought. I had all but given up until I watch this video. 20 minutes later the job is done. Thank you.
@HeadlightRevolution 4 жыл бұрын
That's why we're here! Happy to help
@andreww1212 3 жыл бұрын
Awesome video. Did the same on my vehicle and never had an issue with my front and rear LED turn signals. Even through intense heat and cold.
@HeadlightRevolution 3 жыл бұрын
Thanks for the comment
@law6595 Ай бұрын
I have to take time and tell you something Great job and well done man! My company policy on this install is very similar to yours. Your demo is easy to follow and implement to individual situations. I do question the piercing of all wire jackets…we would actually find the connection before piercing a jacket and possibly allowing a water/fluid/debris contact situation Please continue making your fun easy to follow and excellent content for all of us!
@daveparrent5469 3 жыл бұрын
Thank you for this video. After trying several searches and attempting to make sense of some other videos, yours was spot on and answered all my unknowns. I have a 1998 Toyota 4Runner that I had, on the spur of the moment, decided to replace the burnt out conventional bulb with LEDs--I bought Sylvania bulbs. After doing so, I noticed the ABS light on my dash; through a Google search, I quickly discovered I needed a load equalizer, so back to O'Reillys for it. Through other searches, I already knew the wire I needed to tap into with the equalizer was the green one with a white line on it. Instead of attaching the other end of the equalizer to the common wire (white with a black line on it), I crimped a connector on it that had a hole for a bolt, and then I just used the existing grounding point behind the side panel instead. Everything worked--no more ABS light. Thanks again.
@HeadlightRevolution 2 жыл бұрын
No problem Dave! Glad we could help!
@molon122 3 жыл бұрын
This video answered virtually every question I had in regards to LED lighting and resistors. Thanks!
@HeadlightRevolution 3 жыл бұрын
Glad it helped!
@Jestr86 2 жыл бұрын
doesn't say you need a resistor for each signal or 1 resistor is all that's needed.
@PBS-nm1uu 3 жыл бұрын
This is one of the best videos you guys have made, you touch on the most important things.
@tylerromano517 3 ай бұрын
Best explained/brokedown video on KZfaq yet, will be calling for my resistors or bulbs!
@chippewalee6936 3 ай бұрын
You are an amazing instructor. Very thorough and can easily understand. I've been a mechanic for years so I understand what's going on but for someone who's just lost on what they are doing you did an awesome video
@AlbertDM 3 жыл бұрын
Holy crap! This is the best tutorial video that answers literally every question I had. The Diode Dynamics video is trash which doesn't have close-ups of where each wire goes into the resistor or the use of either a multimeter or cheapo tester. I think you just got yourself a customer. Thank you!
@HeadlightRevolution 3 жыл бұрын
Glad you liked it! Thank for the comment!
@rsomazzi 3 жыл бұрын
I have a 2021 Tundra and both tail lights have (2) wires on the turn signal only. This is great because I didn't need to test which wire was which like you had to in this video (with 3 wires). I appreciate the details in this video including how hot these resistors can get. Because they do. After installing your kit, my blinkers are back to normal pace now. Thank you for this video because it enables dummies like me to do the work ourselves.
@HeadlightRevolution 3 жыл бұрын
Working on vehicles can be a task sometimes, especially with electrical work. It makes us happy that our tutorial videos are helping people like yourself install parts or solve any issues they are having with their vehicles. Thanks for the comment & keep having fun working on your 21 Tundra, those are indestructible.
@kevineccleston8341 5 жыл бұрын
Chris Your voice is excellent. I think your KZfaq is a great example of the right way to make one. It's other videos I have seen with computer generated narrative that I think are are creepy.
@harmonsonrobinson2698 6 ай бұрын
1996 f350 7.3 auto trans. Swapped my bulbs to LED, put a resistor ground to ground and had Overdrive issues still, this explains better that I need flasher to ground with the resistor. I’ll try that before throwing in the towel going back to factory bulbs.
@floex831 5 жыл бұрын
I was scared to install resistors before this video. So easy with the help of this video, thank you so much!
@HeadlightRevolution 5 жыл бұрын
You got it!
@playerhaterr6172 5 жыл бұрын
Dont be scared no more little bobby
@KDFRxpo2 4 жыл бұрын
floex831 Don’t!!! These resisters get extremely hot and can cause of fire. Just get a electronic relay.
@jeffreysmusic Жыл бұрын
@@KDFRxpo2 most new cars dont have them
@brianfields7519 5 жыл бұрын
Excellent video. All the answers in an easily explained format and very clear and steady filming.
@HeadlightRevolution 5 жыл бұрын
Thank you for the support!
@brianfields7519 5 жыл бұрын
@@HeadlightRevolution Chris, 2008 Yukon XL. Put JDM LED's all around. Installed 1 resistor to the tail light (used your example to determine Ground and Turn). Used crimp on's to connect. Signal still blinks quickly and resistor started to warm up so connection was good. I'm thinking of soldering instead. Before I do all of that, my question is this; would I need to put resistor's on both front & rear (in this case left side) in order to see the blinking difference? Are they mutually controlled in the computer module or separately (should I have experienced quick blinking up front but controlled in rear after the install)?. Thanks in advance., waiting to hear from you before I proceed.
@HeadlightRevolution 5 жыл бұрын
@@brianfields7519 You will need Resistors in both Front and Rear to prevent Hyper Flash issues, once Resistors are wired into both Blinkers on one side Front ant Rear, the Hyper Flash will go away. :)
@mr.boostang2064 4 жыл бұрын
Never have I done this before and I'm horrible with electrical stuff but your video helped me install some resistors on my 07 Explorer 😁 now my LEDs flash normally 👍
@HeadlightRevolution 4 жыл бұрын
That's great!!
@ig2933 Жыл бұрын
This video is excellent! I have a 2018 Equinox and this video was a life saver. It's a really easy process after you do the first one!
@HeadlightRevolution Жыл бұрын
We're glad this video helped you! Did you mount them with screws like mentioned in this video?
@ig2933 Жыл бұрын
@@HeadlightRevolution Yes! My Equinox is tough because the front turn signals are separate from the headlights, so I mounted the resistor just above the wheelwell. I also soldered the wires together and it works beautifully
@peterburke2198 5 жыл бұрын
Great job guys and making it so easy and simple instructions to follow. Thankyou and have a great day.
@HeadlightRevolution 5 жыл бұрын
thank you Peter!
@EfrainLynn 4 жыл бұрын
Best video ever! Thank you so much I've learned more in this video then I have all day! 👍
@billybrown640 Жыл бұрын
After watching this video I'm confident I can set up my resistors. Thank you.
@mr84ttop34 3 жыл бұрын
Thank you for sharing and explaining this the correct way.
@HeadlightRevolution 3 жыл бұрын
You're very welcome!
@kevhed8 5 жыл бұрын
What a great video on everything I wanted to know about LED resistors
@HeadlightRevolution 5 жыл бұрын
Glad it helped!
@jaystewart6396 4 жыл бұрын
As well used led resistance for 2013 Toyota matrix turn signal front and back turn signal put in led switchback lights white turn orange
@michaelk7299 5 жыл бұрын
Great video! Thanks for taking the time, this helped me a lot.
@HeadlightRevolution 5 жыл бұрын
Happy to help!
@christopherwarren7374 3 жыл бұрын
This is a great video as I am new into led conversion . My Chevy sonic does not have a turn signal relay so this is the alternate rough. Some vehicles have a turn signal relay and in that case you just have to swap it out with a new led relay "If Available ", GM made it so my AC and turn signals are built into the same relay , so, don't want to play with mother nature on the AC and use a alternate relay , other wise, If you have a LED turn signal relay you can buy for your vehicle you dont have to do what you see here. Thanks for the video, good stuff
@HeadlightRevolution 2 жыл бұрын
No problem Chris!
@jonathan-dallasgutierrez3632 3 жыл бұрын
Great video,thank you so much for this informative installation guide .
@HeadlightRevolution 2 жыл бұрын
Glad it was helpful!
@RobertoFernandezRey26604 5 жыл бұрын
The best tutorial, now I know how to install these resistors. Thank you very much.
@HeadlightRevolution 5 жыл бұрын
No problem! Let us know if you have any questions in the future
@bertram-raven 3 жыл бұрын
Remember to switch an RMS multi-meter to direct read. The RMS functionality will make the on/off reading of the indicator less obvious.
@carnage50x 5 жыл бұрын
I had 1 fail. It was in my aftermarket taillight assembly. It had a built in led board inside. There was a small metal box housing 2 mini led's wired in parallel (i assumed to lighten the load and reduce the total heat created). Well for 5 years of operation. Water got into the metal box. It corroded the resistor from the inside. I bought a pack of 6 or so of the same spec of resistors and replaced them. They can fail if not protected from moisture. But it takes a while
@porgie223 3 жыл бұрын
the best video and advice I have ever received thanks you mate.
@HeadlightRevolution 3 жыл бұрын
Glad it helped
@servicetech00211 5 жыл бұрын
Excellent video..... I have a 2016 Ram 1500. I bought some led tail lights and have the issue of an error code when the led’s are installed. Do I need to install resisters for the turn signal AND the brake light? Or is it the same wires. I noticed you installed 2 resistors on the same side in this video...
@HeadlightRevolution 5 жыл бұрын
Hey there! Good question! This specific truck has Two turn signals that neck into one harness. So, we had to wire in Two resistors, One per bulb on each side. :) You only need to use a resistor on your turn signal bulbs, nothing else. If you have installed your resistors and still receive errors and/or hyperflash, double check your wiring to make sure you didn't tap into a parking light, or similar wire. If the problem persists, give us a call and we will help you out! :) 218-755-5505
@Ygglur 5 жыл бұрын
As always a great video.
@davidsteinborn1554 2 жыл бұрын
I bought LED turn signals with resistor built in. Works great.
@HeadlightRevolution 2 жыл бұрын
Sweet!
@Texcajun06 2 жыл бұрын
Spot on. I soldered my connections, painted them with liquid tape, then wrapped them with electrical tape. Overkill I suppose, but that's just the way I'm built. 1999 F350
@HeadlightRevolution 2 жыл бұрын
Heck yeah!
@coachnutt61 5 жыл бұрын
What is the resistance and wattage for your headlights? If they are led non canbus compliant?
@jordanholden4659 4 жыл бұрын
Perfect video! Explained everything nicely!
@HeadlightRevolution 4 жыл бұрын
Thank you Jordan!
@chonsalinas3598 3 жыл бұрын
NOW THATS A VIDEO ID SAY WAS DONE LIKE A PRO BY A PRO !!!
@HeadlightRevolution 3 жыл бұрын
Thank you!!!
@aqua.scape69 4 жыл бұрын
Great video bud. Thank you very much
@HeadlightRevolution 4 жыл бұрын
No problem, thanks for watching!
@rafaelbattle770 4 жыл бұрын
Will the resistors work on a 2018 Dodge Ram 1500 without any canbus issues? Thank you! Great video by the way!
@HeadlightRevolution 2 жыл бұрын
Yes!
@texaslawdawg1902 4 жыл бұрын
That’s what I call a professional video. Bravo
@davidreeves3396 3 жыл бұрын
What happens if you connect the meter to two wires and neither is the ground? Will you not get voltage on meter or the test lite bulb will not lite up/flash?
@wolfmaan Жыл бұрын
This is a HUGE help! Thank you so much!!!
@HeadlightRevolution Жыл бұрын
Glad it helped!
@sagoodman988 Жыл бұрын
Great video, explained it perfectly for myself to understand, thank you!
@HeadlightRevolution Жыл бұрын
Glad it was helpful!
@jmetradingcards 5 жыл бұрын
THAT WAS THE BEST EXPLANATION VID YET. EXCELLENT JOB!!!
@yulphotography9960 5 жыл бұрын
Hi, I just installed some LED for my turn signal light. Although it flickers, I am actually ok with it. My question is do I really need to use resistors? Without them what is the downside beside the flickering. HELP PLZZZZZ !!
@HeadlightRevolution 5 жыл бұрын
If you are fine with the way it is, you don't need the resistors.
@dorotejtaseski 4 жыл бұрын
@@HeadlightRevolution Can Resistors solve the problem for showing erors on dash???
@dioneldallgas-frey5147 3 жыл бұрын
Great explanation learned a lot!!
@HeadlightRevolution 3 жыл бұрын
Glad you liked the video and found it helpful! Thanks for the support😄
@johnjkizer6399 11 ай бұрын
Great video I have switchback turn signal in the front as well as led turn signal in the rear of the car, I have installed 2 load resistors near the rear of the car and everything has been working great until about 1 year down the line when the left turn signal started hyper flashing again I immediately thought it was a burned out load resistor since none of the bulbs were burnt out, just hyper flashing so I replaced the left side with a new load resistor but unfortunately it did not fix the issue, I just have no clue to what is wrong, hopefully you can guide me in the right direction. Thank you very much
@simoneluconi 5 жыл бұрын
Please note. Not all car need resistor. It depends what system che car uses. In new car often you don't need to install resistor, because the timing is computer generated, not by power consumption etc. In my Golf 7 i have installed led turn signal without resistor and they work perfectly.
@STATIC-NITRO Жыл бұрын
What year is your golf 7 ? , i have 2021 altima do you think it needs a resistor , relay or non Thanks in advance
@aezzil3536 Жыл бұрын
@@STATIC-NITRO You can test that by simply taking out the bulb
@mazdiff5477 4 жыл бұрын
THANKYOUUUUUUUUU!!! Exactly what I needed and straight to the point
@HeadlightRevolution 4 жыл бұрын
Glad we could help! Thanks for watching!
@futureshock7425 5 жыл бұрын
Nice video thorough !!!!
@HeadlightRevolution 5 жыл бұрын
Thanks!
@beebeebearbear 4 жыл бұрын
great video. Going to do this on my 2006 Dodge Ram rear signal lights.
@HeadlightRevolution 4 жыл бұрын
Glad you liked it, thanks for watching!
@hiroshi138 5 жыл бұрын
Cool vid. I wasn't sure which wire to connect on the "hot" side. Thanks
@HeadlightRevolution 5 жыл бұрын
You got it! Glad we could help!
@cuda4094 3 жыл бұрын
@@HeadlightRevolution will that fix the cruise control? Or do I have to put resistor to brake wire??
@joeyong1418 4 жыл бұрын
Nice.I just wanted to know how many Ohms are your resistors .
@ulfmusskacken 4 жыл бұрын
Probably about 8.2 ohms
@HeadlightRevolution 2 жыл бұрын
We have a few different styles!
@grvoor4 5 жыл бұрын
Can you guys do a video of the best LED headlight on a 2014-2018 Silverado w/o projectors? There’s nothing, anywhere that provide info. I’m wanting the Supernova V3, however I’m hesitant to buy them due to no info on the pattern or brightness.
@therealmentalk 10 ай бұрын
GREAT VIDEO
@darlalarcom9739 5 жыл бұрын
WARNING. Be sure that any wiring stripped open "especially" on trucks inner fenders or areas that are damp locations, are sealed from the elements i/e solder joints, shrink tube, spray on electrical tape, silicon, electrical tape. Failure to do so will result in long term damage to your wiring, corrosion will follow the entire span of wire ruining your factory electrical wiring harness. Keep water and salt water out. Very important. Make minimal cuts into original wiring when at all possible.
@RockyJ_Concepts 5 жыл бұрын
Tjank you. One of the best utube video demknstrations with clear illustrations and explanations. This jndicates that you are a specialist and work safely...well, you know what you're doing. Congratulations!
@lovetricia 4 жыл бұрын
Why wouldn't you just use your probe in the socket and not strip anything especially if your using t-taps and if you know enough to solder would hopefully know to insulate. I know it's not your video I just haven't seen any comments on not stripping unless you have to.
@Tweeter1007 4 жыл бұрын
I personally find it much easier to solve the fast flashing issue by simply installing an electronic flasher in place of the standard one(a simple plug in) which normally sells for about $9.00. It also saves on power usage, unlike substituting a filament bulb with a resister to mimic the same wattage draw in the circuit. It's a whole lot less work not altering your wiring too!
@HeadlightRevolution 4 жыл бұрын
Installing an LED flasher is certainly a much easier route! However, most new vehicles do not use a relay to control the turn signal anymore, and it's all done through the BCM. So in those cases, wiring in a resistor is the only option.
@Tweeter1007 4 жыл бұрын
@@HeadlightRevolution Yes that is very true of most newer vehicles that now have a BCM do the job, in that way it cuts the cost, and they are proving to be very reliable. The down side is having to keep the draw on the circuit close to what the original incandescent lamp used by way of a resister which is more work to wire in than simply changing over to an electronic flash as we did on our older models. I have a 09 H2 that has the BCM, so if I want Led turns, I have no choice but to throu in the resisters in parallel with the bulbs. Thanks for responding, and I do hope more sites will mention that the E flasher is a great option when their is no BCM. Another monkey wrench you can encounter, mostly on the foreign cars is the can-bus systems. But that's a topic for another day😉!
@Reddum990 2 жыл бұрын
I have a 2022 Jeep Wrangler Rubicon JL. I'm following instructions for a delete kit that takes the front drl light/signals and swaps it to a small circle light in the delete. I have my ground, blinker, parking wires. Blinker to one side, and ground on the other. I've tried adding the resistor to run with each wire, I did the wire taps like you did here. Blink outside is normal, inside its fast. Also with the resistor hooked up the parking lights won't work. And btw it's Rough Country's fender delete kit I'm installing.
@bigpopparich3 4 жыл бұрын
Thanks for the great video. I'm looking to do so ASAP when mine arrives. However, in my Caddy, there's a sealed cover involved. Where would I put the resistor then? Thanks in advance.
@HeadlightRevolution 4 жыл бұрын
The headlight or tail light should have a main wiring harness that goes to the assembly, you will need to find the power and flashing 12v wires within that harness and tap into those wires there.
@dga223 4 жыл бұрын
Excellent tutorial.
@HeadlightRevolution 4 жыл бұрын
Thank you Dan! -Chris W
@repairvehicle 5 жыл бұрын
why install LED that requires resistor? why not leave factory bulb? what is the gain of having LED in the tail light or turn signal? By the way good video, I appreciate your work.
@HeadlightRevolution 5 жыл бұрын
LED bulbs are much brighter than stock incandescent bulbs, which is great for road safety and turn indication, and it improves the overall look of your vehicle. They also draw less power and have a more crisp and immediate power-up time, where stock bulbs will blink at more of a delayed pace.
@linushedwall9838 5 жыл бұрын
@@HeadlightRevolution don't they draw more power if you put in lots of resistance on every single bulb though?
@van8365 5 жыл бұрын
luzing power is same with detectors or resistors you lie to ass why?
@endofword2012 5 жыл бұрын
Led have longer LIFE...realy longer. almost never die
@dinosoarskill17 5 жыл бұрын
And I think another advantage is it would come on quicker than a traditional bulb, while it may be very minute and have small/no difference, it's enough for some companies to deploy marketing strategies for it, for safety. :p
@futureshock7425 5 жыл бұрын
Anyone just install leds and let them hyperflash? Lol
@HeadlightRevolution 5 жыл бұрын
We have seen it a few times. Not sure why though.
@spencero3278 5 жыл бұрын
Some motorcyclists leave them hyper flashing for added visibility
@kthax308 5 жыл бұрын
Yes I did....it flashes normally for a few seconds then goes to hyper flash. I have to say it’s a little bit annoying. I’ve got the resistors but I wanna make I know exactly how to install them.
@jasonstewart8926 5 жыл бұрын
I have questions for u 2009 ford escape led tail lights color wires taps in two used led resistors as well turn signal in them roo led reaistors .help out thank u for time
@kthax308 5 жыл бұрын
future shock.......did you really get that hyper flash or were they flashing like the truck lights in the video? I replaced ALL my exterior bulbs with LED without the resistors and the the flashing is faster but it’s nothing sneeze at......it’s probably twice as fast. Not that bad.
@ratecoudo 3 жыл бұрын
Good video man thank you very much.
@HeadlightRevolution 2 жыл бұрын
No problem 👍
@mickc4633 5 жыл бұрын
Thank you
@matthutch5919 10 ай бұрын
Many THANKS for this video. ❤ your honour towards honesty. A test light will definitely be good enough for this job. Although I've never seen my multi meter with that sort of reading so I'm using that 😅 😂🤣🤣
@HeadlightRevolution 9 ай бұрын
Glad it was helpful!
@bruin1131 5 жыл бұрын
Thanks bro. Good video. Very helpful.
@Querencias7 5 жыл бұрын
Ditto. Thanks HR.
@HeadlightRevolution 5 жыл бұрын
You got it!
@eugeniocarrasquillo303 5 жыл бұрын
Great Explanation
@HeadlightRevolution 5 жыл бұрын
Thank you!
@cindygolden4728 Жыл бұрын
Thank you!
@HeadlightRevolution Жыл бұрын
You're welcome!
@WolfmanVon 3 жыл бұрын
Good stuff much appreciated, dealing with this classic car
@HeadlightRevolution 3 жыл бұрын
Glad this was helpful, let us know if you need help with anything!
@WolfmanVon 3 жыл бұрын
@@HeadlightRevolution sure thing I appreciate you!
@HeadlightRevolution 3 жыл бұрын
Not a problem!😃
@mijynshareef55 3 жыл бұрын
Awesome video. Really appreciate it. My question is that do I install a resistor on each corner i.e., 4 resistors; one for each indicator bulb or will 1 resistor take care of all four? Thanks
@HeadlightRevolution 3 жыл бұрын
That is correct. Thanks for the comment also.
@oritrond 3 жыл бұрын
thank you for making this! I do have 1 question however. I have an 04 Chevy Malibu. Replaced just about EVERY exterior light (lol) with LED's. Question I have is, if I put a resistor in the tail light, do I need one in the front blinker as well or will that 1 resistor cover it all? I'm guessing from this video, I need to put one at both ends of the car so I would need a total of 4 resistors. Again, great video and thank you for sharing this with the world!
@ac_junior72 2 жыл бұрын
Thanks so much for this!
@HeadlightRevolution 2 жыл бұрын
No problem!
@kalebeligibson9363 2 жыл бұрын
Omgosh!!! Thank you very much!!!!!!!!!
@HeadlightRevolution 2 жыл бұрын
No problem 😊
@marketwarriorfx Жыл бұрын
My rig started hyper blinking when I swaped the front blinker bulbs, would I put the resistors on the front? My front bulbs don't have a specific blinker wire as it runs into a connector that plugs into the headlight itself and is then wired according inside. Thanks for the video!
@thomassimmons1947 2 жыл бұрын
He explained it perfect 💯
@HeadlightRevolution 2 жыл бұрын
🙏
@itzkrvmbz 4 жыл бұрын
Had to put 2 resistor on each side of my 17 tahoe, but its working great now
@HeadlightRevolution 4 жыл бұрын
That's great to hear!
@8383pcb 4 жыл бұрын
Just curious why you had to put two on each side. I ask cause I think I might need to do that. My issue is when my headlights are off the flash fine, when head lights are on I get hyper flash. Just to note my tail lights are also my blinkers.
@formetopoopon2057 3 жыл бұрын
What's the difference in doing this & just changing the flasher relay? I upgraded my 02 RAM with LED taillights & all I did was swapped out my flasher relay to stop the hyperflash? Will it damage anything if you don't have led resistors installed?
@FunWithAJ 5 жыл бұрын
Excellent video.
@HeadlightRevolution 5 жыл бұрын
Thank you
@marcuswainscott818 6 ай бұрын
Outstanding video sir. Thank you very much.
@HeadlightRevolution 6 ай бұрын
Very welcome!
@JayTX. Жыл бұрын
Thanks for the tips , Having issues with side markers on C10 after front bulb swap , should resisters on the side markers fix the issue, already have electronic flasher
@Reckless_est96 2 жыл бұрын
Much appreciated my g 🙏🏾
@HeadlightRevolution 2 жыл бұрын
Any time!
@tonykhan7212 3 жыл бұрын
Very well instructions !!
@HeadlightRevolution 2 жыл бұрын
Thanks, Tony!
@2fast278 4 жыл бұрын
Hy i like your videos . They are awesome. I learned alot o things ith the lights . Cand you tell me wht ristor i need fo a VW PASSAT CC 2011? Thank you very much
@ritchiemarsteller8884 5 жыл бұрын
Hi, great video. I do have a question... I have a 88 S10. When I put in zevo LED tail lights. They light up but nothing works. No brake lights, no blinker. I was told to get a load resistor. But your video indicates this solves the speed of the blinker. Will the resistor make my tail lights work. Also I was told to get a led flasher. What's your opinion on that? Thanks Rich
@HeadlightRevolution 5 жыл бұрын
Hey there! We have a few questions for you. Give us a ring sometime today and we can help you out! 2187555200
@Alaa-89-0 2 жыл бұрын
Awesome video thank you.
@HeadlightRevolution 2 жыл бұрын
Glad you liked it!
@kylekaae4986 3 жыл бұрын
Change to the blinker fuse (in your fuse box, it makes a clinking nose) that has a voltage regulator in it. Plug and play, worked for my f150.
@blazindragon296 3 жыл бұрын
flasher relay is what you mean to say.
@Efrainacon 3 жыл бұрын
Explain
@idanf620 3 жыл бұрын
Thank you for sharing the video with the useful information 🙏 I came acroos that video while trying to get my turn-signal LED bulbs works. I have a Suzuki s-cross (crossover) 2013. Turn-signal lights are PY21W. I replaced the 4 of the halogen ones with 4 Osram ledriving SL PY21W Amber. 2 LEDs on front doesn't work at all (they are tested other way and not faulty). 2 LEDs on back of the car blink faster then usual. 1. Do i need to switch the car's wires polarity of the front plugs? becouse that kind of bulb base can't be fixed other way to change polarity (because of the 2 pins on 150° that make you fix the bulb only in 1 position). After sorting out the answer to question 1: 2. About the fast blinking issue - do i need to put a resistor near any LED bulb (4 resistors at sum)? Or put 1 resistor near 1 LED bulb is enough for the whole 4 turn-signal circuit? Best regards! Idan
@HeadlightRevolution 3 жыл бұрын
We will need some more information before we can assist you, shoot us an email with this information and infoprmation on if you are using any PWM modules or any added modeles to correct that issue. When we get that email, we will be able to assist you with this! Thank you for your time, and have a great day! Sales@HeadlightRevolution.com
@cxriley98 3 жыл бұрын
Question do you need this for all led conversions upgrades or just the turn signal upgrades?
@everardocamacho5063 Жыл бұрын
I got a 1989 toyota pick up 2.4.liters,what kind of resistors do I need? Thank you great video
@garnetf10 4 жыл бұрын
Awesome 👏 video
@HeadlightRevolution 4 жыл бұрын
Thank you for watching! I’m glad we could help.
@psycho0002 2 жыл бұрын
awesome Video
@HeadlightRevolution 2 жыл бұрын
🙏
@vernonjackson6387 3 жыл бұрын
Fantastic video. The step by step was excellent. Will you do the same if you have LED headlights that flicker?
@HeadlightRevolution 3 жыл бұрын
That will require a little different part and process, we would ask that you email into us if you have any issues with your headlights, but it could indicate that you need a pair of PWM Modules that I have linked for you here: www.headlightrevolution.com/gtr-lighting-pwm-hid-kit-modules-ACC.PWM5202.MOD_2?quantity=1
@borndiy5490 4 жыл бұрын
THANKS....I never knew of how to wire lights. Still having mine done by a shop but great to know. I plan on buying me that tester at Walmart....SMILES....did not know how it worked and the wire spliter. Neat tools I don't have. I'm having Led Pillar Lights installed on 2019 Rogue rear window hatch. Can't wait for the cool look. Thanks again, great knowledge you have given... :-)))
@Mafu26 5 жыл бұрын
Can you tell me the difference from 50w 8 ohm vs 50w 6 ohm resistors? Are both gonna do the job?
@everardocamacho5063 Жыл бұрын
Great video,just one question do I need a resistor for the front turn signals and if use led ligths for the cluster do I need a resistor too ,my truck is a 1989 toyota pick up,thank you for your advise,and cheers from ontario ca.
@peterandjaja 5 жыл бұрын
Will resistors make the LED bulbs go brighter? I'm trying to replace the Reverse stock bulbs on my Lexus SC300 with LEDs but I feel like it's not really giving out that much brightness in contrast to what the LED power output should be. Also, the breaklight indicator on the dash has gone on so I assume it really needs some resistors to be installed?
@andykeen6219 2 жыл бұрын
Really helpful thank you A*****
@HeadlightRevolution 2 жыл бұрын
Glad it helped
@d.brownm1092 5 жыл бұрын
Good video. Just finished installing resistors on my 2011 GMC Sierra. They're on the tail lights and front turn signals. Started out good. No hyper flashing during the day. Hyper flashing returned when I turned the headlights on. Where did I go wrong?
@zohaibanwar5919 5 жыл бұрын
I am facing the exact same issue.
@SanMario95 5 жыл бұрын
I have tail lights that have LEDs built in and the “built in” resistors went out about a week ago when I took my truck to get washed. The whole tail light functions as a turn signal rather than just one half of the tail light, so would I need to put resistors on the top and bottom harness on each side of the vehicle? A total of 4 resistors?
@bmcmike26 Жыл бұрын
With using the T-Connector/Soldering, if I were ever to go back to Halogen bulbs, would this compromise that and need to replace harness?
O'Reilly Auto Parts
Рет қаралды 170 М.
Enlight Automotive
Рет қаралды 992 М.
Headlight Revolution
Рет қаралды 5 МЛН
Headlight Revolution
Рет қаралды 87 М.
Alla Lighting Automotive LED Bulbs
Рет қаралды 25 М.
Common Motor Collective
Рет қаралды 161 М.
Макс Ващенко
Рет қаралды 218 М.