How [NOT] to MAX test a power supply!

Рет қаралды 75,278

Жыл бұрын

Keep exploring at www.brilliant.org/Brainiac75 . Get started for free, and hurry-the first 200 people get 20% off an annual premium subscription.
How hard can it be to max power test a power supply? After finding out my laboratory power supply will deliver more volts than advertised, I have decided to test how many watts it will deliver. The issue is that I don't know how? In this video, I will give it some attempts and learn from the mistakes... Will the power supply deliver the watts it is supposed to?
My Patreon-page: / brainiac75
Did you miss one of my videos?: / brainiac75
FULL MUSIC CREDITS
Time codes: 0:01 + 7:30 + 11:03
"Long Note Two" Kevin MacLeod (incompetech.com)
ISRC: USUAN1100420
Time codes: 0:44 + 8:44
"Energizing" Kevin MacLeod (incompetech.com)
ISRC: USUAN1900040
Time codes: 2:52 + 6:18
"Perspectives" Kevin MacLeod (incompetech.com)
ISRC: USUAN1300027
Time codes: 3:58 + 10:42
"Adding the Sun" Kevin MacLeod (incompetech.com)
ISRC: USUAN1900041
Time code: 9:43
"Peace of Mind" Kevin MacLeod (incompetech.com)
ISRC: USUAN1200099
All music above licensed under Creative Commons: By Attribution 3.0 License
creativecommons.org/licenses/b...
Time code: 5:50
Mix of two tracks:
1) The Shimmering by fran_ky (freesound.org/s/237363)
Licensed under Creative Commons 0 license
2) "Spacial Harvest" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3.0 License
creativecommons.org/licenses/b...
ISRC: USUAN1100653
#Max #Watts #PowerSupply

Пікірлер: 219

@thegoldengood4725 Жыл бұрын

time to miserably fail my exams by using 90% of my brain cells, powering off when realising the paper has a back page

@prla5400 Жыл бұрын

Bro that feels like dying 😭

@rther7006 Жыл бұрын

Genuinely a question. What's the difference?

@derkevevin Жыл бұрын

*Windows XP shutdown noise*

@iamdarkyoshi Жыл бұрын

Mike's electric stuff has an amusingly simple means of load testing, just put some enameled copper wire in a bucket of water. The enamel is thin enough it can conduct heat from the wire into the water, but prevents it from corroding from being a dc potential in water. Tune the amount of wire to the desired resistance, and then if you need a longer runtime, use a bigger bucket of water.

@BadMax02_VR Жыл бұрын

its exactlly how i tested my DIY 2000w labbench powersupply with those chines dc to dc setp down transformers and server powersupplies in series i think they are called RD DPS5020 modules 50v at 20 Amps and 2 of those for 50v 40 Amps, and what can i say, i boiled that water as fast as a kettle and those modules actually were handeling it quite well. which is just crazy for how small they are. no consumer electronic load would have been able to handle that amount of power, only if i would use like 5 of these shown in the video which just wasnt viable for just a simple extreme load test.

@Speeder84XL Жыл бұрын

Nice idea! So simple, yet functional. As long as the wire isn't all too thin compared to the current running thru it and the water temperature is kept constant, the resistance will stay constant. It's more important to keep the temperature constant for copper though. Wire wound resistors and metal film resistors are usually using high resistance metal alloys that is made to have small variations with temperature - even though the resistance can still change a little bit, if they get very hot. But copper may have something like a 5% increase just going from for example 20 to 50°C (for example if the water temperature is allowed to rise). But it also depends on your application how large deviations in resistance that can be accepted. If some variation can be accepted, heating wire can also be a good option if a lot of power need to be dumped - since those wires can get red hot for long periods without damage 😃Many of those alloys can go from room temperature to red hot with only 10% resistance change - some like Kanthal A1 is as low as 5 % increase going from room temp to over 1200°C (which is like yellow hot).

@victortitov1740 Жыл бұрын

i wouldn't call it amusingly easy, as it requires a fair bit of experimentation to get the right resistance with a reasonable length of wire. But it definitely is amusingly cheap and accessible.

@FindLiberty Жыл бұрын

How does using wire in mineral oil compare to using water for the heat sink?

@victortitov1740 Жыл бұрын

@@FindLiberty water has higher thermal capacity, will boil if overheated, is cheaper, and is less of a mess to clean up. Oil is an insulator, so it is better for high-voltage application. It may be a fire hazard if overheated.

@gallium-gonzollium Жыл бұрын

1:52 “I can even watercool it” this made me laugh more than it should have

@berni8k Жыл бұрын

It is normal for lab power supplies to go a bit above. That way they make sure you can get up to 30V and not 29.99V

@user-tz3fd8hm4q 2 ай бұрын

Yeah, mine is listed as 30V 5A, but it's actually 31V 5,1A.

@StormBurnX Жыл бұрын

I would love to see the benchtop power supply's output on a scope. Wonder how noisy it is.

@sarowie Жыл бұрын

it will be tricky for him to measure. Even as an EE: You need to specify a test scenario like the resistor, because it does not create its own artefacts, but also the resistor does not care about PSU quality.

@FindLiberty Жыл бұрын

With the switching design, there might be "a lot" of noisy HF AC hash riding on the DC and even some 50/60 Hz ripple at high current loads, especially when set near max voltage. In most cases, it won't be a problem with less sensitive circuits. The specs should give the numbers you'll need to decide price/performance sweet spot. The little, low cost switching boost reg boards (not stepdown/buck benchtop P.S.) can be hideous sources of noise.

@yuxuanhuang3523 Жыл бұрын

I have a linear power supply from UNIT-T and tested it. It is mostly fine, except for a 50Hz base from the grid. But for a switching PSU, the noise could get much higher. The common solution would be to add capacitors to the outlet, but it hurts the PSU's ability to respond to really fast changing loads and may cause a power loss for sensitive systems that sometimes spike in current.

@FindLiberty Жыл бұрын

@@yuxuanhuang3523 Long live linear - 9 out of 10 capacitors agree! lol

@berni8k Жыл бұрын

We had one of these supplies at work. They are the most noisy lab power supply i have ever seen. You get what you pay for

@thegeek3295 Жыл бұрын

I really like the electronic load unit. Never seen one before. I also note that when using the 3 ohm resistor it still hit 31.7V @ 9.68A which is over the rated 300W. So even though its cheap, its pretty damn good too.

@thewhitefalcon8539 Жыл бұрын

You can't get one any more because the company CONRAD is shutting down

@Barkingstingray Жыл бұрын

Crazy to think the first time I saw one of your videos was when I was a sophmore in highschool extremely excited to show my physics teacher your content. Fast foward 3 years, I go to school for physics, 4 more years, I graduate, and 2 more years since then working in the field :) (wow insane, 9 years of your videos) thank you so much for your inspirations and learnings, this type of experimental and hands on content feels so much like a consequence free (for me haha) lab in university and i just love it very proud to be a patron after all this time

@AaronBlankenship Жыл бұрын

This is a critical teaching method that some people do not get right: you must show failures. Human simply do not learn properly without failures being involved in the lesson.

@brainiac75 Жыл бұрын

Yep. Failures and understanding why it failed is often more enlightening and memorable than just seeing something that works. Thanks for the early watch!

@sarowie Жыл бұрын

absolutely. I am worried about electronic loads because Dave Jones created an oscillating circuit using the constant power. Here, we saw the constant resistance mode and also saw oscillation. Oscillation can kill both devices. Meanwhile honestly: Neither the cattle nor the resistor where a "failure": that was just approaching the limit in an easy to understand and fail safe way.

@stu_jam Жыл бұрын

Collab between Braniac and Elctroboom? Blow electronics up with lasers!

@brainiac75 Жыл бұрын

Could be fun, though I prefer to keep my electronics in a functioning state ;) Thanks for the early watch!

@stu_jam Жыл бұрын

@@brainiac75 agreed in hindsight, stuffs expensive 😂

@sarowie Жыл бұрын

Interresting. I rember Dave Jones (EEVBlog) torture testing a PSU with an electronic load set to constant power. Electronic Loads are awesome, but as you have already experienced: It is very very easy to get them to oscillate and from there, you can kill power supplies.

@XShadowCatzX Жыл бұрын

No matter what happens in that day, if Brainiac uploads, it’s a good day.

@brainiac75 Жыл бұрын

Thank you! It is also a good day for me when a video is finally released. After a month of thinking and working on the same video, it is a relief to publish it :)

@XShadowCatzX Жыл бұрын

@@brainiac75 aww dude, i cant imagine the stresses of deadlines for yt and stuff, especially if you have no ideas lol. I love the content dude, keep it up!

@Mario4445d Жыл бұрын

every day is good when real madrid loses

@glidercoach 8 ай бұрын

@@brainiac75 I need an affordable 240v to 120v transformer that will handle a 1400 watt power tool. I am in Italy. Can you suggest a supplier? Ebay has many, but the quality?

@dimitar4y Жыл бұрын

... The two devices fighting because of ohm's law has to be the most unintuitive but obvious error. I want an episode just on various caveats like this where obvious things are easy to miss.

@Darkshadow799 Жыл бұрын

Really interesting video, i was genuinely surpised about the instability issue. It would be really nice to see with a scope the ripple on the voltage waveform.

@sarowie Жыл бұрын

I was concerned for a moment, because that is nasty use case. Dave Jones toured a PSU with an Electronic Load in Watt mode. Using Resistor mode is a bit less concerning, but still: As said here: Both devices try to regulate/limit current and voltage, but the electronic load also tries to regulate ratio of voltage to current as secondary controll loop, using the current as primary control loop. That can oscillate. Oscillation can kill the PSU. I would not blame the PSU for dying under such a test.

@katranian Жыл бұрын

Another quality video! Keep it up, we enjoy these!

@brainiac75 Жыл бұрын

Thank you very much! I do put a lot of time into these videos - glad is appreciated. Much more to come!

@victortitov1740 Жыл бұрын

The oscillation has nothing to do about on which side of ohm's law equation they are. it's all about how the feedback loops of the load and the power supply are tuned. It's complicated, we'd have to dive into all of the internal circuitry to properly explain it. The simple explanation might be, both are optimized for constant-voltage operation, because it is the more common application.

@conejero00 Жыл бұрын

Exactly Ohm's law can be V/R=I, making R and I on different sides of the ecuation and it will still wooble

@maskrtnik01 Жыл бұрын

Honestly, this is exactly what I thought of, after I saw this video. Ohm’s law can be arranged in three forms, so provided explanation sounds weird. Now I got an electronic load, and I can confirm, that in my setup, power supply in CC and load in CR are stable.

@cbfull 6 ай бұрын

That a “reverse power supply” is a thing is so amazing 🤩

@executive Жыл бұрын

ohms law simply describes a relationship. The symbology doesn't matter. You can rearrange the equation to put whatever properties you want on whatever side. For example I=V/R

@Gubby-Man Жыл бұрын

8:17 I love the 3210. Used to play Snake on it all the time as a kid.

@TheRailroad99 Жыл бұрын

When testing linear PSUs (not sure if this one was linear or an SMPS) maximum output does not equal maximum stress. That is because the PSU has an electronic load in it self to dissipate the rest of the power. For example if you dial in 10V@10A, but connect a load with 0.5Ohms resistance, the current limiter in the PSU has to dissipate half of the power. With a 1Ohm load, it has to dissipate nothing.

@thewhitefalcon8539 Жыл бұрын

This is certainly not linear. I have this exact PSU and it is quite light. It is obviously a relatively cheaply built SMPS. (And why wouldn't it be an SMPS? Sometimes lab power supplies are dual-stage switching+linear, but I've never heard of one being pure linear)

@GQuack Жыл бұрын

This was a rather interesting video, and not what I had expected just by seeing the thumbnail. Keep it up!

@phinok.m.628 Жыл бұрын

It's actually really common for lab bench power supplies to have a higher max voltage and/or max current than advertised. I'm not entirely sure why, but I guess it's just to be able to guarantee it can handle the rated power.

@berni8k Жыл бұрын

It is just to make sure they get get to exactly 30V and not 29.9V. They are cheep analog things inside so they are not very precise (they rely on you turning the knob to the exact value)

@askjacob Жыл бұрын

Generally it is to compensate for wire losses at higher currents, you may need the extra headroom to get 30v at the other end of the connection

@dhawthorne1634 Жыл бұрын

Sticking with the crude and cheap method, the "massive cooling" would be as simple as a couple of canned air dusters. If you turn them upside down, you get liquid air to help cool your resistors. I've used this method on CPU dies when troubleshooting without having to keep removing a cooler. (Tin shot glass set directly on the die and dribble in liquid air). Alternatively, the average capacity of a standard refrigerator is 350 watts and the capacity of higher end consumer grade chest/upright freezers is 700-900 watts. Drop the temp on your refrigerator to the minimum, pop in the capacitor with the wires running through different sides of the door seal and you've got sub-ambient cooling perfect for your experiment. As for your added radiator, the air gap would make it more or less completely useless. Maybe you didn't show this step, but using some thermal paste or thermal pads would greatly improve the cooling capacity, as would a small fan.

@AndrewGillard Жыл бұрын

Just be careful with the canned "air" dusters in electronics and related experiments :) Those cans are typically filled with a refrigerant like butane, not regular air (compressed air requires very thick and heavy tanks). Therefore they tend to be highly flammable or even explosive. Having a connector/switch spark shortly after using one of those cans would certainly make the day more interesting ;) This isn't just a theoretical risk, either - I've done it myself. I used one of those cans to blow dust and crap out of a 4-way trailing mains socket on the floor, then plugged something into that socket around 10 seconds later. The plug pins arced when they made contact, igniting the butane and engulfing my hand in a flash of flame with a loud pop. I was completely unharmed, thankfully, but I hadn't used the can very much. The thing is, _I already knew it was butane!_ I just absent-mindedly forgot for a minute 🙄

@AluminumOxide Жыл бұрын

6:49 notice the lego model of the International Space Station!!!

@nlhans1990 Жыл бұрын

This is a harsh test for the transformer, particularly the primary windings as it needs to deliver max current. However, high power linear power supplies usually have multiple secondary winding taps at different voltages, and then use a BJT transistor circuit to curtail the last few Volts of that tap to reach your desired output. Say the transformer has taps at 9V, 18V, 27V and 36V. The BJT circuit always needs a couple of Volt to operate. Hence the 9V would be used for outputs up to say 5V, the 18V tap up to e.g. 14V, etc. This could be a reason why the PSU reaches 32V instead of 30V, as the transformer could output less V with a low line voltage, and the BJT circuit could heat up and have a higher voltage drop. However, notice that in order to properly stress test (e.g. "burn in" or "burnout" test) the PSU, you would need to get the maximum voltage drop over the BJT. In my example figures, the PSU outputing 32V@10A=320W from a 36V tap, means the BJT circuit is only dissipating (36-32)*10=40W. But note that if you shortcircuit the output, that the PSU would likely use the 9V tap, "curtail" 9V to reach 0V/10A output, and internally dissipate 90W(!). If you want to grossly overload the primary side of the transformer, then don't use a shortcircuit but a voltage at which it just about needs to use the highest tap, at max current. So say it changes taps over for Vout

@MarkkuS Жыл бұрын

8:15 As a Finn I always appreciate the mentioning of our lost Art of mobile phone industry.

@EdgarCorona Жыл бұрын

Haha, the Nokia 3210 reference, loved it.

@brainiac75 Жыл бұрын

I just immediately thought of the Nokia when I realized it could have been model 3210. Such a classic :D

@OkiemElektroniki Жыл бұрын

Very cool video and great explaination of basics electric laws. btw. It would be nice to make a video about efficiency of that power supply, for instance make a graph every few volts and see how much power does it consumes vs how much power it gives.

@Random_4400 Жыл бұрын

I actually have 2 of thease power supplys and they are amazing for what they cost me, my ones where actually able to output almost 11a at 32.1v!

@cryptophoenix3031 Жыл бұрын

for how much did you buy them?

@JustPyroYT Жыл бұрын

Great Video as always! 👍😀

@sulfie46 Жыл бұрын

Messing around with cheap power supply! Hope to see some magic smoke!

@brainiac75 Жыл бұрын

Would be sad to blow up my only lab power supply ;) Thanks for the early watch and comment!

@DWScienceVideos Жыл бұрын

I actually have a power supply similar to that one, and it is overspec as well. i think it is because if you turn up the course voltage adjustment only, that gives 30 volts. But if you also turn the fine voltage adjustment up it adds an additional 2 volts to that, giving 32 volts.

@gabrielv.4358 Жыл бұрын

Great video!

@PeterMilanovski Жыл бұрын

So I'm not the only one who uses a kettle as a load dump! Sometimes you get so much solar production that you have to put it somewhere so the kettle it is, my coffee consumption has gone up dramatically since I started this LoL 🤣

@VideoInformation Жыл бұрын

Good info

@sulaimanabdullah952 Жыл бұрын

Electronic loads are usually switch mode and can easily cause power supplies to be unstable at certain settings. A few hundreds of low-esr uF across the supply usually fixes this problem.

@moth.monster Жыл бұрын

I can recommend keeping a fire extinguisher nearby. I have one at my desk, never had to use it but it's always there just in case. I also have one in the kitchen too, since cooking involves hot stuff.

@Yreq 23 күн бұрын

I thought, that everybody had forgotten Nokia 3210 long ago, untill now😅 I came here for science, but get much more. Thank You😁

@voidnull9438 Жыл бұрын

I’m interested in the efficiency of the plugs and in products, my class is currently doing a topic about it so I think it would really help

@imnotbeluga007 Жыл бұрын

I had a Wanptek KPS3010 PSU, but it failed shortly after getting it. I don't know if I overloaded it or the design was really crappy, but I kept getting major voltage fluctuations (like you), that would eventually stress my projects. And one time, I got a 15V spike while powering a 5V load, and as I was concerned, I turned off the supply, only for it to go bang a while later when I tried turning it on. After days of troubleshooting I found out that the main IC (TNY277) was overheating, and this caused the switching MOSFETs to short out and blow the fuse, rectifier, thermistor and other parts.. I was powering a powerbank circuit at that time, and it completely fried it. A major power surge went through, as the regulation failed and the switching transformer let the surge through. I'm not trusting Chinese stuff ever again... especially after paying 90$ for it...

@samuelfellows6923 Жыл бұрын

Chineseum crap in that case 😠

@imnotbeluga007 Жыл бұрын

That power surge wasn't from the mains. The power supply made it, along with making a loud bang! I'm gonna have to make myself a new power supply, as I can't tinker without a reliable power source.

@imnotbeluga007 Жыл бұрын

@@samuelfellows6923 And my unit had weird "seizures" at times since the start. Maybe I had a defective unit? And the major PSU "seizure" happened while adjusting the current. I had 3 minor PSU "seizures" before. Of course, I couldn't return it, as I was curious and I voided my warranty and stripped the screws....

@napalmholocaust9093 Жыл бұрын

I have the same one but a 30/05. 24 bucks on eBay new 8 years ago. I noticed the internal fan only came on for a second to test at power on and never other times when it ran for a week straight. I lined-up the fan from a timer to blow straight into the front grill of it. They run together so why not let one fan cool 2 devices. If you're wondering why a timer would ever need its own cooling fan its b/c it was a one rpm synchro motor turning a metal disk with numerous contacts. Every 8 seconds it was off for 2 seconds. I couldn't find a simple timer that could switch like that so I made one. But it runs hot.

@marluna_x Жыл бұрын

The thing where the power supply actually delivers more volts that advertised also happens to a 60v 15a power supply my dad borrowed from a friend. It can deliver 16a and 65v! I (=my dad) also own a old 32v 4a analog power supply, therefore it also has analog displays. Their markings go from 0 to the advertised limits, however its display arrow things go beyond that by a little bit too! (They also have a mode to double the shown numbers, as a way to see small currents easier)

@Guardian_Arias Жыл бұрын

this was fun, but i like my Raiden RD6018, it's a 1080w max power supply at 60v and 18a but limited to 600w because its powered by an old 600w power supply from an old decommissioned pc that can luckily provide 12vand 50a with all of its rails tied together and a boost converter in-between that can handle upping the voltage from 12v and 50a to 72v and 20a all for 60USD from a direct from china app on a sale. no fire so far especially considering i used plywood and 3d printed PLA to build the housing and mounting brackets.

@daijoubu4529 Жыл бұрын

You can probably modify the PSU to output more than 12V but will have to replace the capacitors

@didotb01 Жыл бұрын

I wonder how many years I've been watching this channel and it's still too damn entertaining .. EDIT: just checked .. ever since 12 years ago huh .. have had to change accounts 3 times 😂 nostalgic

@fmdj Жыл бұрын

Very cool!

@coltenh581 Жыл бұрын

I didn’t see it in my brief peruse of the comments, so I’ll say I am interested in the efficiency video

@styrishrodrigues Жыл бұрын

Awesome video.. I love electrical related videos

@defeatSpace Жыл бұрын

Pretty cool!

@FakeMichau Жыл бұрын

watercooling the load? genius!

@XANApwns Жыл бұрын

Ooooh, that ISS model is something I'd definitely like to see more of! I also follow your facebook page, would you post more about it there?

@jacquesb5248 9 ай бұрын

good equipment.interesting

@jamess1787 Жыл бұрын

It's been years since I've seen a video from you. Looks like your channel was unsubbed by that KZfaq bug s few years ago. Glad you're still around. Missed your Scandinavian voice 😂

@loudsonicbug2195 Жыл бұрын

very interested in efficiency!

@ngeowhoiwan1050 Жыл бұрын

Normally when I test load the amperage, I would use car (12V)/ truck (24V) halogen bulbs either in parallel or series rather than using load resistor/s because from the brightness of the bulb I can however estimate it's voltage and wattage.

@Hobby_Electric Жыл бұрын

8:00 This is because your Load has a regulation circuit wich handle than not that good. May try ohter brands ;)

@JohnJones-oy3md Жыл бұрын

10:56 - I wouldn't mind seeing some magic smoke being released.

@Tigerisverycute Жыл бұрын

Not me saying hi back after he enthusiastically said “HI!”

@tyttuut Жыл бұрын

My Rigol DP712 (50V/3A) will go up to 53V/3.2A and provide that reliably. I've always wondered why it's like that.

@sarowie Жыл бұрын

the voltage is obvious: if you need 50V on the load, you need more on the source. If you can not get 50V at your load when the source has 52V, then it is your problem. If the psu barely makes 50V under no load, then it can not provide 50V to the load.

@CaptainKirk01 Жыл бұрын

I like your dragon electrical clips, Shirley must have been the result of a Karen! Nice touch!

@neail5466 Жыл бұрын

Yes please, efficiency vs loading.

@brianjrichman Жыл бұрын

Working at the limits = Letting the magic smoke out. FUN!!!

@swirrllfolfsky9803 Жыл бұрын

I've got a very similar variable power supply, so I'm pretty interested to see what the outcome will be

@-ADACOR- Жыл бұрын

The multi tapped transformer based ones can take more of a beating than the purely digital/smps ones

@laser8389 Жыл бұрын

"A resistor is usually boring to me. In my mind it is just a badly-conducting wire."

@janadden8762 Жыл бұрын

nice Video

@sophiegrey9576 Жыл бұрын

brian in the hazard warning going 'syke'

@jaedenspider877 Жыл бұрын

You should try powering a hair dryer with that power supply Because hair dryers use a DC motor and a rectifier

@RussellTeapot Жыл бұрын

7:25 this part cracked me up

@Joe3D Жыл бұрын

You should have put the 2 resistances in parallel... 😁

@Random_4400 Жыл бұрын

11:02 yes please maje a video about it!

@Ramog1000 Жыл бұрын

Shouldn't a labbench power supply be safe, even at the edge of its powercapabilities? I mean I don't expect it to supply the power for long but I expect it to cut the power once it heats up to much. Also another thought, I live in Germany and was able to buy a psu from the same brand at conrad, shouldn't the unit be safe regardless of setting according to consumer safety laws?

@Damn_it. Жыл бұрын

This video is like my class 😅

@DavidSprings Жыл бұрын

Clever way to ask for a like. You got it.

@BH4x0r Жыл бұрын

I think you should test some longwei/topshak psu's, they're even cheaper and done very well in my usage, despite their lightness and size

@Scyth3934 Жыл бұрын

They might have worse noise though.

@sarowie Жыл бұрын

@@Scyth3934 might be true, but that would not matter for this channel. An electro magnet does not care. ... but the electromagnet will kick the input protection circuit to hell and back when switching improperly, so... maybe stay with better power supplies?

@BH4x0r 10 ай бұрын

@@sarowie anything i ran on them ran fine, and they're cheap as hell when discounted that includes Arduino's and other MCU's, even on the NPS605W (60V 5A model) it's best to avoid the 2 dial ones tho, those are pretty finnicky to get the right voltage and even will often temporarily peak far higher while turning it up (K3010 for example), but the NPS (course and fine tune knobs) models are perfect for my usage and don't have that issue since i don't really trust the 2 knob models too much i mainly use them to either charge something like a lead acid battery or one is in use at a local slot car club where they had 1 PSU down and 10A for a single track was enough for all classes they run there

@Remi_Jansen Жыл бұрын

i have a cheap power supply like this aswell, works fine tbh!

@Paxmax Жыл бұрын

WHAT?! No fire? No POP! ..ooh wait.. This isn't PhotonicInduction!

@solarfluxman8810 9 ай бұрын

3.00 ohms for 77.7 feet of 5/8 inch wide, 0.015 inch thick, stainless steel banding material, at temperature of 140F.

@600322 Жыл бұрын

When I tested a power resistor rated 100W 2 Ohms with a lab power supply 30V x6A=180W I cooled the resistor in water.

@ghassanALKIRSHI Жыл бұрын

can someone explain to me why connecting dc to ac rated device ?

@GustavoSoares-vx5ne Жыл бұрын

The extinguisher trigger looks like a arrow in the thumbnail 🤣

@toalan Жыл бұрын

It is a switching power supply, it being able to supply the rated power is expected almost regardless of price or size.

@johncoops6897 Жыл бұрын

LOL WHAT?

@toalan Жыл бұрын

@@johncoops6897 If this was linear power supply then it would be worth making a video on.

@johncoops6897 Жыл бұрын

@@toalan - either kind of supply can "exceed" or "not meet" ratings.

@heinrichberger3908 10 ай бұрын

No flames, I am disappointed!

@JimGriffOne Жыл бұрын

Note: You can actually overdrive these cheap PSUs. They have internal calibration potentiometers that can be "tuned" to whatever value, within a particular range. So, a 30V/5A supply could theoretically get up to about 37V/6A if lucky.

@thewhitefalcon8539 Жыл бұрын

BASETech eh? I have this exact power supply. I'm sure it's a cheap rebrand of something else though because the brand BASETech is only sold at CONRAD Electronics, which is now shutting down.

@test-rj2vl Жыл бұрын

How does this electronic load control resistance electronically?

@neutronenstern. Жыл бұрын

probably with a transistor, that is shut on and off very quickly, in series with a power resistor. The on off rate determines, how high the average resistance is. (how much average current can flow, with a set voltage). Probably way more complicated, but i think this might be the basic conceptm

@putraadriansyah8082 Жыл бұрын

Add a waterblock and replace the heatsink inside with it

@hanleypc Жыл бұрын

Could you use 2 electrodes places in a solution of salt water as a good load?

@sarowie Жыл бұрын

creating hydrogen gas next to a fully load power supply? using table salt and wondering about the health effect of the gases created? Running into issues with the non-linearity of an salt water bath?

@userPrehistoricman Жыл бұрын

It will also corrode the electrodes

@michaeloberb2120 Жыл бұрын

Way more interesting is how long it can do 10 amps at 1 Volt dumping 310 Watts in its internal heatsink...

@neutronenstern. Жыл бұрын

I think for you to build one power resistor,you only need a lot of cheap tiny resistors and a heat sink.

@LegendSpecialist Жыл бұрын

👌

@roysigurdkarlsbakk3842 Жыл бұрын

Please leave that running for an hour ;)

@ssjihad7014 Жыл бұрын

Interested

@mnikpro Жыл бұрын

Have you planned to make a video about laser safety glasses ? 🤨

@dcallan812 Жыл бұрын

Really interesting video. 2x👍 Big Clive love Ohms law

@dimitar4y Жыл бұрын

You find 500W resistors to be cool, I find them to be hot, however.

@obtrunco Жыл бұрын

Let's max it out.

@scaleop4 Жыл бұрын

👍👍

@Joe3D Жыл бұрын

At 32V 10A maybe the ripple is excessive. Something to test.

@batterynerd8779 Жыл бұрын

I have exactly the same power supply. It‘s actually not that cheap. There are much, much cheaper ones on amazon. Anyway, i use it to charge my batteries and the only Limitation ist, that the terminals get so hot, that the terminals literally melt the plastic around them which leads to a bad connection. So dont overdo the amperage. 8 amps is the limit.

@mibars Жыл бұрын

I'm using the rock bottom 30V 10A switchmode lab power supply, the one that comes without knobs for fine tuning and mine has already starting doing funny things at around 10 to 15V (probably the most used range) when voltage sometimes spikes to around 20V. I guess the potentiometer is going bad.

@Tomazack Жыл бұрын

Not many things in life seems that logic, but ohm's law is.

@harlanfalejczyk2478 Жыл бұрын

your output voltage is within spec! 30 volts is not the same thing as 30. volts.

@marc-andreservant201 Жыл бұрын

Your resistor is not conducting heat properly to the heatsink. You need thermal paste. This is probably okay since you're not hitting the resistor with its full power rating.