How To Fit and Set Up an Aftermarket Gear Selector to a Yamaha R1 2004 2006 Link Below

Рет қаралды 17,263

Жыл бұрын

This video shows you how to fit and set up a Chinese aftermarket gear selector to a Yamaha R1 5VY 2004-2006. From start to finish and set up.
Link to the item is here!
amzn.to/3OuwDUh

Пікірлер: 31

@LyNx_88_R1 Жыл бұрын

Nice 1 matey.. worked a treat for my 03 🎉

@thesaunders 11 ай бұрын

Glad it helped

@KhalidAzam-fu2yh 5 ай бұрын

For Suzuki GS-150, Gear Indicator With Dash modification www.youtube.com/@javedakhtar5231

@user-xh7fg2kc3d Жыл бұрын

Thank u very much for this easy guide🎉

@KhalidAzam-fu2yh 5 ай бұрын

For Suzuki GS-150, Gear Indicator With Dash modification www.youtube.com/@javedakhtar5231

@Rolandmotocom 4 ай бұрын

Stupid question: my FJR1300 has only 5 gears. What should I do in L mode after 5th gear is learned?

@fromabove6214 Жыл бұрын

Great video really help me to install mine. Mine is all fitted with ignition on the L will flash slowly. With the bike turned on the L will flash faster. The L does not change to 1 even with the bike running for over 5 mins. Do you have any ideas what could be wrong? Cheers

@thesaunders Жыл бұрын

I had that problem, I believe in my case, I changed the wire I spliced it from to the other one there. That should do it.

@teodor.N Жыл бұрын

@@thesaunders i think you speak about the green one. I tried on both wires ( light gray and than dark gray) . None of them worked.. The L is flashing slow before you start the bike, and after you start the engine it should start flashing faster.. entering in programming mode, but mine doesn't do that. It stays flashing slowly.. it drives me crazy.

@thesaunders Жыл бұрын

@@teodor.N I really don’t know then! I don’t know much more about them!!

@teodor.N Жыл бұрын

You connected all the wires under the gas tank, right? Those white is simple, mother and father type, the red one to a power cable, and the green one should have worked with the camshaft senzor wires.. but fuck it, it didn't.

@thesaunders Жыл бұрын

@@teodor.N yeah. I just did the bits in the video. Should have worked!!

@CypherBTW 18 күн бұрын

Will that be the same process for the 2008 r1?

@thesaunders 13 сағат бұрын

That, I’ve never tried.. sorry!

@cezarmd2283 10 ай бұрын

What if mine learned only till 4th speed and not 6th? How can I reset it all over again?

@thesaunders 8 ай бұрын

There is a simple way but I'm so sorry I can't remember what it is!!

@pivektv5041 5 ай бұрын

6 times torn key and will caunt from 6 to 1 and automaticy go in L mod (LEARNING)

@user-hp2qs2wr1w 10 ай бұрын

Why not feed a piece of wire through, tape it to the indicator and wiggle it through ?

@thesaunders 9 ай бұрын

Certainly would have worked better in hindsight.

@teodor.N Жыл бұрын

Man, it worked for you?

@teodor.N Жыл бұрын

I did exactly the same wiring but it stays the L flashing.. it doesn't appear 1 at all.. I waited a lot with the engine on..

@teodor.N Жыл бұрын

I think the green one should have been wired to the dark grey one.. i don't know but it won't work for me, yamaha r1 2005 rn12

@thesaunders Жыл бұрын

I’ve done it the same on 2 different R1’s. I don’t know why it wasn’t working in yours.

@goncalofreitas9641 Жыл бұрын

Why that can't be connected to the battery to give power to the gear indicator

@Tjerk_010 Жыл бұрын

How is your wire so long?!🙈😂