How To Remove Ball Joint Rivets

Рет қаралды 5,488

klowny1969

2 жыл бұрын

In this video i show how to remove upper control arm ball joint rivets, the same can be applied to lower control arm rivets. This particular car is a fourth generation camaro but it can be applied to any car with rivetted ball joints. How to replace a ball joint with rivets.
check out my channel for more videos:
How to change a tire pressure sensor (TPMS) yourself:
www.youtube.com/watch?v=PDpDm...
Dakota digital dash Install (1982-1992 Camaro)
• Dakota Digital Dash In...
How to install a 4L60E transmission:
• How To Convert a Stick...
How to Wire A Switched fuse block:
• How To Wire A SWITCHED...
Complete Brake Overhaul:
www.youtube.com/watch?v=TVA0t...
Vintage air serpentine setup:
www.youtube.com/watch?v=ByVdD...
How to Upgrade your fuel pump:
www.youtube.com/watch?v=8-7sB...
How to install an electric vacuum pump:
www.youtube.com/watch?v=i1n3b...
How to build a camaro from top to bottom:
www.youtube.com/watch?v=5twT_...
400 Cubic inch small block Dyno testing:
www.youtube.com/watch?v=eavm4...
How to Clock an Alternator:
www.youtube.com/watch?v=_I24m...
How to Replace a u-joint:
www.youtube.com/watch?v=QQsXs...
How To install a trans pan drain bolt:
www.youtube.com/watch?v=zXFCB...
How to install subframe connectors:
www.youtube.com/watch?v=9n1Yc...
How to do a quick wheel alignment (toe in toe out):
www.youtube.com/watch?v=Ycdoo...
klowny1969 - best car mechanic on youtube
Only clown mechanic in the world ! Uses for an air hammer
This video can be applied to chevy, ford, mustang , impala , camaro , corvette, truck , toyota, lexus , honda , nissan. etc.. volvo cadillac gmc astrovan truck blazer silverado turbocoupe thunderbird clown clowny69 klowny69 GMC Savana 2500 Siera 1500 Sonoma isuzu hombre GMC desoto mopar vice grip klown garage restoration old school relics will it run barn find hasn't started in 45 years 1930 1940 1950 1960 1970 1980 barnfind

Пікірлер: 27

@blockhuggerdoeboy357 2 жыл бұрын

Don't miss doing this, too the shop it goes!

@klowny1969 2 жыл бұрын

I hear ya!

@stringbender11672 2 жыл бұрын

Hell yeah. Old school but still fast. Took me waaay longer to do this job a couple yrs ago on my 79 camaro. But I got it. This will get saved to my camaro Playlist. Thanx Klowny🤡

@klowny1969 2 жыл бұрын

Sometimes you gotta go old school LOL

@budsodalsky 2 жыл бұрын

Awesome! this is the type of video we need that the dumb magazine guys dont show you - juss an easy way to do ball joints removal for the little guy with hand tools - thanks clowny - hey i noticed that this time - you suggested red ANTI-butter sauce!

@klowny1969 2 жыл бұрын

Lol antibutter sauce..I love it!!

@budsodalsky 2 жыл бұрын

@@klowny1969 You should have that one sidekick on again too- that guy you said something to - about "smells like aunt so and so" he helped you with the 2.8/3.1 water pump

@baxojayz 2 жыл бұрын

Nice work. I hate riveted ball joins, but this reminds me that it is not too bad.

@klowny1969 2 жыл бұрын

Yep..just have to take your time

@fls360 2 жыл бұрын

Das Klowny went all out cut and drive style!

@klowny1969 2 жыл бұрын

Dis is whut I do!!

@fls360 2 жыл бұрын

@@klowny1969 And when you done with it you can say "Dis is whut I dids".

@tamarajohnson3576 2 жыл бұрын

Hi Klowny 1969 I had a question about a 1991 Oldsmobile Delta 88. My friend changed the battery and bought a new battery. The car wouldn't crank it does turn over though. Could you tell me what could possibly be the problem. I also want to know if I can use 1997 parts of a Oldsmobile Delta 88 and put them on the 1991 Oldsmobile. Thank you so much for being awesome with cars. You helped me a lot

@klowny1969 2 жыл бұрын

If it turns over by hand then check to see if you are getting power to the s terminal on the starter..could be a starter relay or fuse..for the parts, go to rockauto.com and see if the part numbers are the same for those years..thanks for watching