How to Replace a Lower Ball Joint (short, quick version)

Рет қаралды 7,427,740

10 жыл бұрын

Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below.
Press out a Ball Joint (In-depth): • How to Replace a Ball ...
Here is where to get the ball joint press: www.amazon.com/gp/product/B002...
Torque Wrench I use: amzn.to/1N65Maz
Socket Set I use: amzn.to/1BlL0Tj
How to check your ball joints to see if they are bad: • How to Check if a Ball...
In-Depth Version: • How to Replace a Ball ...
Upper Control Arm Replacement: • How to Replace a Contr...
How To Press a Ball Joint: • How to Press a Ball Joint
How to Change a Wheel Bearing: • How to Change a Wheel ...
Torque Specs are for my 2001 Mazda B3000
(each make and model will have different torque specs so check your service manual for proper torque specs.)
-Lower Ball Joint
83-113 ft-lbs and tighten to the next slot for the cotter pin (don't back the nut off)
-Upper Control Arm Ball Joint
35-46ft-lbs
-Caliper Bracket Bolts
85ft-lbs
Link to the part:
www.autopartswarehouse.com/sku...
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday*
-Website: www.ChrisFixed.com
-Facebook: / chrisfix8
-Twitter: / chrisfixed
-Instagram: / chrisfixit
-Subscribe Here: kzfaq.info_c...
-KZfaq Channel: / chrisfix
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

Пікірлер: 1 600

@bryandixon1830 3 жыл бұрын

I did it! My 2001 B4000 now has new lower ball joints, upper control arms, shocks and camber bolts. I took it in for a professional alignment, but everything else I did myself - with your help! Thanks so much Chris. You made all the difference. I would not have done this without your channel. Keep up the great work!

@krijntoet8446 7 ай бұрын

Nice work Bryan, I know the feeling ☺

@spelunkerd 10 жыл бұрын

This kind of snappy, well edited and condensed video is the ideal format for DIY videos here on KZfaq. The message, from author to listener, is that you respect my time. I wish all authors understood that. Thanks!

@chrisfix 10 жыл бұрын

Thanks for the feedback! I try to edit ever second of the video to make sure it is as concise as possible. I hate watching how to videos where the person talks on and on about random stuff or even stuff related to the job and you are 5min in and still havent seen it.

@chrisfix 9 жыл бұрын

Jim Marcum Thanks Jim! I appreciate the feedback as well!

@Jsroca89 6 жыл бұрын

Hey man! My Moog lower ball joint I got doesn't have a spot for the pin like my oem joints. They are "self locking". Is this right/safe. Should I go oem?

@claudiarangel5653 6 жыл бұрын

spelunkerd tjxgx

@kinjalpatel7094 6 жыл бұрын

spelunkerd 9924271247 coll?.

@spicytuna62 Жыл бұрын

Chris has probably got one of the most useful channels here, and a lot of the content doesn't really age because suspension technology hasn't really changed much on regular cars in the last couple decades.

@chrisfix Жыл бұрын

Thanks and exactly!

@mobileterminaluser 7 жыл бұрын

my wife knows your vids by just your voice. That's how much i like watching your repair vids. Thanks for making them🖒🖒👏

@BLADExARTx5160 5 жыл бұрын

"Honey?! Are you watching Chris fix again?!" 😂😂😂

@johnmcgowan2348 3 жыл бұрын

Always a well crafted instructional video. No lame rock and roll intro, no babbling. Clean and concise.

@babuljannattv8537 2 жыл бұрын

I am your New friend love for Pakistan

@noah4878 8 жыл бұрын

Hey Chris, thank you so much! I was driving the other day and the right ball joint on my car completely fell apart. So I investigated and found out I needed to replace the lower ball joint. I have wrenched on cars before but I've never really touched the front end/suspension before. After studying this video and tackling the replacement I successfully replaced both sides lower ball joints on my car. I cannot thank you enough for the excellent quality and straight forward how to videos you put out on this channel. Thank you!!! A shop wanted $320 per side and I spent $60 on 2 ball joints!!

@rushisom7349 6 жыл бұрын

noah4878

@jeremiahfisher6994 5 жыл бұрын

They want 800 to do mine. Christ 2hrs watching his video I can do this

@TheDeviousDave 5 жыл бұрын

One shop wanted 320 for both & another wanted 190 for both... The choice here is obvious but holy shit thats still expensive just for some little ball joints

@grimmkaosify 5 жыл бұрын

Do you have to get a alignment after doing this

@TheDeviousDave 5 жыл бұрын

@@grimmkaosify No you don't, that's usually for tie rods

@D_R_Martin 6 жыл бұрын

Very useful video. I just replaced my upper ball joints on my pickup and will need to do the lowers the end of the month. The pace of the video works well, and the fact that the tools are relatively simple makes it all that much better.

@bdrichardson403 7 жыл бұрын

Great job of teaching...good filming, easy to understand what you do and I can understand every word you say.

@chuckdecarlo4456 9 жыл бұрын

Straight-forward and to the point! THAT'S How to do an instructional video. VERY well done Chris.

@chrisfix 9 жыл бұрын

chuck decarlo Thanks Chuck! That is how I like to make my 'how to' videos! New automotive 'how to' videos every Thursday and most Mondays so stay tuned!

@averyalexander2303 6 жыл бұрын

What happened to uploading videos on Monday and Thursdays? I really enjoyed watching your new videos! :(

@MegaDealDays Жыл бұрын

@@chrisfix l0

@chriscusick6890 7 жыл бұрын

This video is so thorough and well made. Very professional with the novice mechanic in mind. Not like a video made in the dark or missing steps. No wonder you have almost 1.25 million views. Also using quality tools on a clean subject! Congratulations on a superior job.

@chrisfix 7 жыл бұрын

Thanks a lot Chris!!!

@rachelhancock6833 8 ай бұрын

Chris, could you tell me if I need to change them on both sides if only one side has gone bad? And is it true that you need to change your tire rod and have an alignment after doing the ball joint? And is it best to change the upper and lower at the same time even if only one or the other is bad? I’m such a mess since my truck broke down and I want to make sure we do everything right 🙏🏻❣️

@ianno3 7 жыл бұрын

Your videos are by far the highest quality I've seen on KZfaq. You're doing a huge service to everyone. Thank you so much.

@bishbosh7728 7 жыл бұрын

ianno3 I like his videos alot also as most of his repairs are on the same truck I have so very helpful.

@williamcraigdavis3231 2 жыл бұрын

Simplest explanation of lower ball joint replacement. And the bonus is a clear view how to use the ball joint tool.

@Marc9889 7 жыл бұрын

This is no doubt the most well-produced auto fix it video I have ever seen. Thanks for taking the time to do such a good job making it.

@chrisfix 7 жыл бұрын

Thanks!

@nickphillips4398 4 жыл бұрын

You can tell by how easily it all comes apart that he’s not in the Midwest lol

@williamallen6802 4 жыл бұрын

Yea im from wi myself and my lower ball joint needs to be pressed down looking at the new one but the castle nut is towards the top not the bottom so this doesn't help me. My 99 s10 2.2 rear wheel drive doesn't have a cv shaft like you see in all of these videos. I did get m factory rivets out of my upper ball joint though ^^.

@steelisthemeal 3 жыл бұрын

Especially the Joliet Illinois area. Salt for daysssss

@Masoncakes97 3 жыл бұрын

He's in NJ, believe me everything is rust here. He probably just got lucky

@BroadwayLTDProductions 3 жыл бұрын

In Michigan we deal with salt but because our roads are so bad, nothing has the chance to seize up before a massive pothole destroys your suspension system again. Lol

@baconqot8324 3 жыл бұрын

@@BroadwayLTDProductions you're not wrong, these roads are brutal

@6SPDLS162 3 жыл бұрын

By far the best auto repair guy on KZfaq. Very informative and thorough. Keep up the good work man it helps many of us

@darrinsiberia 11 ай бұрын

"hey guys this is a short summary video" *still shows a way better video than 99/100 YT'ers...* You're the man ChrisFix!!!!!!!

@bushcarftsurvival-life4195 5 жыл бұрын

Chrisfix I just want to say thank you for sharing your videos that is so cool of you to explain these videos like you do I am 48 years old still learning and you explain these so well I hope you keep making videos of working on cars and trucks you make it look so easy I love your KZfaq videos I hope you don't stop making these cool videos because people can learn so much and I'm sure you will get rewarded in some way thanks again Chris fix that's all I can say or I could say more.

@chrisfix 5 жыл бұрын

Thanks a lot and I’m glad you’re learning a lot!!!

@odeogbole2297 4 жыл бұрын

By far the best video on Ball joint, thanks.

@Harloha 6 жыл бұрын

Thank you again, I'm a plumber by trade and been looking to change my lower ball joints myself, I have basic skills but just want to be 100 percent positive before I start the job. After watching dozens of videos, I was starting to give up, then I came across your videos, instantly subscribed. Thank you sir for taking time to make these videos. Much Aloha.

@chrisfix 6 жыл бұрын

Awesome! I am glad the video was helpful!!!

@ephraimcamacho9600 3 жыл бұрын

I have to say Chris all these years you have made some of the best videos and Info!!! You are a great teacher!!! Thank you so much for your help!!

@kevinowsley1602 3 жыл бұрын

Chris, well done, as usual. Your cinematography and timing are super clean and you obviously have a knack for 'fixing' things. Good job my friend.

@jackstroup2039 8 жыл бұрын

cool video I just did my ball joints on my Dana 44 and it was a task. keep them coming

@kevinwest9263 7 жыл бұрын

Wenever im about to start a project, i always research it on youtube. Your videos are always the best and most informative. Keep up the good work, bro.

@JeremyWilliamson 5 жыл бұрын

THIS is such a GREAT tutorial, informing, detailed, easy to understand, but also not boring either... MAKE MORE!!

@GrzegorzDurda Жыл бұрын

This video is excellent and ALSO underscores the importance of regularly washing the underside and all suspension components so they never reach this level of crust and crud. It'll extend service life and make it much easier to work on when needed.

@sergiozamorano6413 5 жыл бұрын

Is very important to replace this ball joints. They can become dangerous if not replaced when needed. Thanks for the video

@jamaalharmon6305 4 жыл бұрын

sigh. :O i can't afford to replace my right now :

@ll_sch1zophr3ni4_ii9 4 жыл бұрын

@@jamaalharmon6305 try to find some of a good quality at a junk yard . They are not expensive new, if you do it yourself you can save a lot of money . Is not easy but try it there's a lot of videos on how to do it

@stepanbychkov7710 4 жыл бұрын

I agree with that

@clarencezeman192 8 жыл бұрын

I liked this video because he cut out all the small talk jibber-jabber & turned the camera off in between procedures. Told us what we need to know in short quick version.

@chrisfix 8 жыл бұрын

Thanks!

@JesusGodHolySpirit3 5 жыл бұрын

Not really in depth he talks way too much as well this is a 9 minute video way too long could of been 7 minutes.

@TestAccount-uu9vp 4 жыл бұрын

you dont need one of those g clamps to get it out, my dad uses the weight on the car to push out the ball joint, if you drop the jack fast enough it pops right out

@dudihsalahudin6507 4 жыл бұрын

@@TestAccount-uu9vp 7

@matthewc4025 4 жыл бұрын

This guy literally does the BEST basic auto repairs videos on KZfaq. Seriously great videos man!!!! Your tie rod video saved my ASS😂😂

@johntrauger68 7 жыл бұрын

Thanks for stressing the importance of torquing. Several video's I've watched for this same task never mentioned a word about it. From an old industrial maintenance technician.

@gordonkearney7356 6 жыл бұрын

Hi Chris I'm becoming addicted to your channel. For a young man you are so informative and impart a great deal of knowledge in an easy to understand manner. I would fly all the way from Scotland to attend a summer school if you did such a think. As said I drive a 38 year old classic and the old adage is if you want it done right do it yourself. As there are so many shops will take your money and do a half hearted job at best. I don't believe that you would ever take a shortcut with any job. All the best Gordon

@MeiGunner 7 жыл бұрын

Good video ,, short , informative and Simple .

@jromero1840 8 жыл бұрын

Great vid, clear and concise.

@thenonoman 5 жыл бұрын

One of the best edited tutorial videos I have ever seen. Great job.

@ddggttyy 5 жыл бұрын

I love your videos. Your making sure we can clearly see everything everything you do parts and all is priceless. I've been a subscriber for a couple years and after watching a few videos from other channels it makes me appreciate you even more. thanks!

@pmor5992 5 жыл бұрын

your vids are concise and to the point excellent;-)

@chrisfix 5 жыл бұрын

Thanks

@nickblake1674 9 жыл бұрын

Great job mate! nice one. Will be following this vid when I change out the ball joints on my Pajero in a few weeks.

@akarobbass9469 7 жыл бұрын

Your videos are best because you stay on course and are short and concise. Most all other videos have way too much talking. Thank you!

@pgo301 4 жыл бұрын

GREAT, I've got a B2500, so it's probably close to the same. But the big thing is that this can be done, but not to take it too lightly. Realize and respect what you are doing and you can safely and successfully accomplish this with your help videos. I always take my time when doing something along the lines of major automobile operation. Thank You !!

@RickStewart1776 7 жыл бұрын

Damn Chris, you made that look easy and almost fun .. almost.

@dahltonguilbeau4354 8 жыл бұрын

great video. You really simplified things for me. Be blessed.

@galeonad668 6 жыл бұрын

Dahlton Guilb

@dylang7468 5 жыл бұрын

Almost 5 years later and this video is still helping people out!! Can’t wait to do my ball joints and tie rod end!

@danielruvalcaba6174 6 жыл бұрын

Love the editing and the brief but purposeful talking, great job!

@ayodeledavidakinpelu7936 7 жыл бұрын

Hey Chris love your work brother!! Do you have any videos on inner or outer tie rods/ tie rod ends, living in the motor city, the pot holes destroy our suspension man.

@jimmydawd2619 7 жыл бұрын

this video is great like some arts. you doing great job

@missinglinq 7 жыл бұрын

This is one of the best DIY videos I have ever seen. Well done!

@johnmichaelignacio8167 6 жыл бұрын

I learned a lot by just watching your video. I can easily determine what my clients are looking for. Keep it up

@ImaLoneWolfintheWoods 8 жыл бұрын

The real skill here is you actually can make great you tube videos while fixing things lol

@andrewstarkey4604 6 жыл бұрын

Evelyn Castañeda

@Punk_fluffy 6 жыл бұрын

true that!

@boosted_spirit 3 жыл бұрын

Id be too busy cussing at the fuckin thing im trying to fix

@itzpro. 2 жыл бұрын

@Holly Labus 🤣🤣🤣

@cobra60six 8 жыл бұрын

Good Job, you put a great vid together :-)

@chrisfix 8 жыл бұрын

cobra60six Thanks a lot man!

@idrisbabangidasuleiman2637 7 жыл бұрын

ChrisFix is it just me or you sound down / under the weather?

@deanwill14 6 жыл бұрын

can you use a ball joint seperator or do you have to have a press

@davidm3210 11 ай бұрын

Old boy was flexing on that axle nut! Nice tutorial as always, thanks & best wishes.

@FireEater 7 жыл бұрын

Chris you make some of the best videos on auto repair that I've ever seen Tks from Queens NY.

@mondotone73 9 жыл бұрын

A simple trick before installing the ball join is to put it in the freezer (or use can of air upside down right before installing) the night before so it'll shrink oh so slightly and be easier to install. Oh and blast everything the night before with PB Blast. If it's a classic car then PB Blast it a few days in a row before doing the work. I take this back. dont use PB blast. use half acetone & atf fluid. it's a whole lot better and way cheaper. i use the old atf. and you dont have to wait either. learned this the hard way. used pb blast on exhaust studs. 1st one broke and then the rest came off with ease after the new penetrating oil formula.

@chrisfix 9 жыл бұрын

mondotone73 Awesome Tip! Thanks for sharing!

@mykenwood830 8 жыл бұрын

great vids Chris. Your fish vids are great too !

@chrisfix 8 жыл бұрын

mykenwood830 Thanks a lot!

@alviktor2715 8 жыл бұрын

+ChrisFix DUDE YOU'R THE BEST. *****

@EnvoyExpress 6 жыл бұрын

I have been doing mechanical work since the late 1980's and I like the way you do your videos.

@johnefever5905 5 жыл бұрын

One of the best instructional vids I've seen on KZfaq. I might just give it a try!

@cakeentertainment9655 6 жыл бұрын

This guy legit!

@ImpactedWorld 6 жыл бұрын

1:01 "Suck it." Great videos! i've watched the majority of them

@gerardreed613 4 жыл бұрын

Great video. Easy to follow, precise instructions, easy step by step illustration. Thanks for the info.

@bookoobeans 8 жыл бұрын

You do some of the best how to vids, produced very well too, with just the right level of detail to show the how and why. Thanks man!

@chrisfix 8 жыл бұрын

+bookoobeans Thanks a lot! I spend a lot of time trying to make them concise and easy to follow!

@jayhockley8841 3 жыл бұрын

I always place the wheel that I removed , under the vehicle along with the jackstands , etc . Its cheaper to replace a Rim , Than a Limb .

@chrisfix 3 жыл бұрын

Good point! That's why I always make sure any car I jack up has backup safety in case something fails!

@Bushcraft242 6 жыл бұрын

Awesome learning

@FerrisNikki 5 жыл бұрын

Hey thanks for these videos! I'm able to work on my Tahoe with no problem the way you explain things! Much appreciation!

@frantic1380 Жыл бұрын

Good video. Great production value. You spent a lot of time cutting out the fat. Excellent

@mr.bluegrass9723 2 жыл бұрын

I just got home from getting a estimate to have this done , now I will do it . by the way 350.00 per wheel was the estimate. thank you

@dnb_gaming2588 2 жыл бұрын

Same here

@jasonletzelter6863 2 жыл бұрын

Also same, doing it in about 30 minutes with my dad- best of luck my guys!

@emmanuelgen196 2 жыл бұрын

@@dnb_gaming2588 yj

@emmanuelgen196 2 жыл бұрын

@@dnb_gaming2588 imjhm

@anon8638 2 жыл бұрын

@@jasonletzelter6863 how did it go. Parts cost?

@bB-vh4vh 7 жыл бұрын

nice to see someone use a braker bar first and not destroy there ratchets

@richmac918 7 жыл бұрын

I agree - he uses his breaker bar all the time - something I am guilty of not doing and ruining my ratchets. I have to start doing it the right way.

@justindevore1832 6 жыл бұрын

Chris you are by far the best KZfaqr that shows how to fix stuff if I ever have trouble I know I go to you and watch your video

@cjcapp2993 8 жыл бұрын

Great vid Chris, precise and to the point without the useless and boring monologue, thank you very much.

@tripjet999 6 жыл бұрын

You should only LOOSEN the lug nuts before raising the vehicle. Removing the lug nuts before raising the vehicle is a recipe for disaster!

@emanuelpitian8696 4 жыл бұрын

tripjet999 actually, the wheel is held in place by the downward pressure of the weight of the vehicle, even with the lug nuts removed, it won’t fall unless you shake it very hard. But to be on the same side, I just loosen them slightly.

@andrewsemel-defeo3395 3 жыл бұрын

I am not a mechanic but it is my understanding that loosening and removing the axel nut but before jacking can damage your bearings. I know some of these rules are just nonsense but any feedback is always appreciated.

@TheRealChirpy 11 ай бұрын

Best way is to not lift the vehicle but have some pressure on it so if the wheel does come off the jack will catch it

@terryevans6977 8 жыл бұрын

your video on lower ball joint removal was the only one of four by others that used any type penetrating oil or lube, myself use brake fluid in a spray bottle, good quick videos without all the mistakes I saw the others make trying to use an air impact wrench. oil very important part of a disassembly and assembly!

@les5386 6 жыл бұрын

Great job on this video buddy. I have an 2001 B2300. Mine only has 49,000 miles but it's getting a little crusty from the road salt and I need to replace the ball joints and tie rod ends as soon as the snow melts. This is the best video on the topic that I've come across so far. Thanks.

@garyiverson 3 жыл бұрын

Thanks Chris! I always like the short version. You hit all the high points.

@babuljannattv8537 2 жыл бұрын

I am your New friend love for Pakistan

@pickadilli 7 жыл бұрын

You have saved my A$$ more than a few times, this being one of them. Keep up the good work man, there are a lot of people who appreciate it.

@F.Krueger-cs4vk 4 жыл бұрын

Wow, that's amazing. Here in Australia, auto repair shops dont lend/lease workshop equipment out to anyone. Great informational video, thankyou for sharing. 👌🏻👍🏻. I'd love to move to the States.

@kawh8719 6 жыл бұрын

that was so helpful! Thank you not only showing me how to fix it, but what the parts are and what a bad one looks like!

@ahmedmualla9390 6 жыл бұрын

Thank you Chris you for all these so helpful and comprehensive videos .

@bertgrau3934 Жыл бұрын

I realize this is an old video, but you teach more about the correct way to use tools than many others. I need to do that to my 2001 Lincoln Town Car. I know I'm going to need a ball joint tool, and do have a good idea on how to use it. You Sir, have confirmed my idea on HOW to use it correctly. However I will use an air impact because I have them, and I'm all for doing it the easiest way possible. Thank you Sir, for such good videos. 👍

@normsalisbury7201 6 жыл бұрын

Great video, it's much appreciated.Looking at replacing ball joints on my Exploder with some confidence now!

@0kewl 5 жыл бұрын

Growing up in a family of mechanics, I knew the $400 charge on a single ball joint replacement was way more than the cost of doing it myself. Each lower ball joint for my 89 chevy stepside was $50, and the ball press was $40. I saved $700 thanks to vids like this. Thanks.

@JohnBuckley 8 жыл бұрын

Excellent Video, great editing and thanks for showing people(and some mechanics) that they need to finish with a torque wrench

@chrisfix 8 жыл бұрын

+John Buckley Thanks John!

@stevenanzelc1440 6 жыл бұрын

Very excellent. Best video teaching I have seen in very long time. Keep up the great work.

@commanderjank9060 7 ай бұрын

This video really helped me, though my all joints press the reverse way. The video enlightened me as to what I needed to do and what tool to use. Thanks.

@davidcarmona9250 6 жыл бұрын

Dude, I've never left a comment before this but ALL your vids are SPOT ON, NAIL HEAD HITTING, BARE BONES KZfaq greatness for DIY'rs. I hope/know you/you'll do well in whatever you choose to do in life. For now, thanx for these vids and great job man, great job...

@jaimesustaita285 6 жыл бұрын

Thks for responding, your the only one did, jimthecarguy, dannerscanner,mechanic oc,south main auto Eric o,& several others never did thks again chris, love watching your vidoes my favorite, u show exactly how to do the work on whatever it is that your doing, learned alot watching them. ...thks again.

@johnr.timmers2297 6 жыл бұрын

The amount of work you must put into your vehicles makes make truck jealous. Seriously, who has wheel wells that clean!

@TheTruthBeToId 7 жыл бұрын

So smooth you make it look easy. Very well composed video.

@somerton123 8 жыл бұрын

Thanks mate for the video no messing around straight to the point and you know what you are doing. I am about to do ball joints springs and shocks and it is a confidence booster to watch this, thanks. from down under .

@chrisfix 8 жыл бұрын

+somerton123 Awesome! Good luck and let me know how it goes!

@joshobrien4451 6 жыл бұрын

Man idk if you’ll get this since these videos are from a few years ago but I just wanted to say how amazing these videos are and the details you’ve shown to get these jobs done! Just bought a 99 b3000 and EVERYTHING i need to fix it on here so thanks for that man! Haha save me a load of money and time 🤙🏼🤙🏼🤙🏼

@2CabrasLocas 7 жыл бұрын

very impressed your using hand tools only in your vids! all great stuff! thanks for your effort!

@georgethomas9436 5 жыл бұрын

Hi ChrisFix. My 1999 Lincoln town car needs upper and lower ball joints. I went with eBay for parts. OEM Detroit. A lot less dollars. Also have to replace the pinion due to sloppy stearing. You videos are the best on youtube for doing vehicle maintenance. Thank you very much.

@joker2712005 6 жыл бұрын

One of the best videos i've watched. Thank you for all the tips and tools used. GREAT JOB !!!! I also love that you made two version short and detailed. Sweeet!!

@chrisfix 6 жыл бұрын

Thanks! I’m glad the video was helpful!

@killerdudecris 5 жыл бұрын

Awesome video! Excellent editing, clear audio. Thanks!

@itsflunkytime1805 6 жыл бұрын

Getting ready to do this on my 98 Mustang. Looks simple enough to me. But I'll probably find more problems once I start lol thanks Chris for all the videos your tips are awesome and I try to use them as I work on my cars and my family's cars too.

@sitatt 7 жыл бұрын

Another really clear and concise tutorial! Thanks mate!

@danielmckenzie6858 4 жыл бұрын

THANKS AGAIN CHRISFIX, I LOVE THAT YOU ARE TO THE POINT AND CLEAR EXPLANATION IN YOUR VIDEOS, NOW TIME TO GET CRACKING ON MY C4 CORVETTE AND REPLACE THAT BAD LOWER BALL JOINT!

@chrisfix 4 жыл бұрын

I'm glad the videos have been helpful!

@danielmckenzie6858 4 жыл бұрын

@@chrisfix I had to go to South Bend last week and I have a mechanic friend there, I chicken out last Friday, that lower ball joint was direct pressed on and even my guy was saying choice words when he was pushing that new one back in, I was glad to pay him $100!

@cdbrown30 4 жыл бұрын

It’s great to see videos like this for anybody wanting to DIY!

@matthewwarner5050 8 жыл бұрын

This video was great at helping me replace my lower ball joints! thanks!

@Komas03 5 жыл бұрын

Wonderful video very efficiently and very effectively recorded showing the captioned task without wasting time slots that leads to boredom in many other's productions. For your kind heart that wishes to serve the public in this manner the Almighty must provide you with good health, happy home and sufficient wealth. We will pray for you too. Glad to know there are people like you on this planet. You must part time teach in some college evening courses on these topics. You have excellent art of teaching within short time.