Husqvarna Chainsaw bike

Рет қаралды 26,412

3 жыл бұрын

Chainsaw bike 2.0 is an updated version of the original chainsaw bike. It utilizes the same 51 husqvarna chainsaw engine. The frame is a men’s 26” bike stripped down no crank or shifters. It uses the modular bike rack from the 40v e-bike. The biggest improvement was the addition of a jack shaft that allowed for a little over 19:1 final drive ratio. #chainsaw #motorbike #chainsawbike
#husqvarna
original chainsaw bike - • Chainsaw bike (the build)
40v electric bike - • BUILDING ELECTRIC BIKE...
mounting sprocket on wheel - • Mounting sprocket on b...
how to make a sprocket - • How to make a sprocket...
jack shaft - • Making jack shaft from...
dual chainsaw bike - • Dual Engine Chainsaw B...

Пікірлер: 54

@aliaslam7613 3 жыл бұрын

Awesome!! Love it when you open it up and hit 30mph! Great upgrade...and that 3D Pen technique is pro.

@JGD16 3 жыл бұрын

Thanks! I think I can hit about 35 mph but unfortunately we started getting snow before I could get there. That pen is really coming in handy thanks for the recommendation.

@edyallreadygalaxy717 2 жыл бұрын

Awesome!

@builds_from_scratch3491 3 жыл бұрын

Great build! What is like the max. rpm your chainsaw has under load like 9000 ?

@lukassyrovy9081 7 ай бұрын

how fast could you go before changing up the ratio? thanks

@MrJwolf989 Жыл бұрын

I'm going to attempt the same with a 55cc Redmax Chainsaw motor. You've inspired me to move away from the scooter build into something a little more practical.

@JGD16 Жыл бұрын

It is a lot of fun to build and ride. Good luck on the build

@beytullahyavuz7127 3 жыл бұрын

How much hp?

@peterherrington3300 2 жыл бұрын

Fun little build . You need a motorcycle fella , you're gonna love it 😀

@jca110 Жыл бұрын

I agree 😂 although, I already have motorbikes and I still really wanna build one of these

@kaangoncu2167 9 ай бұрын

for more torque you can fit a smaller rim at the rear. I think put 16inch kids bike rims on the back. get a thread of the same diameter as the rim and weld it to the rim.

@JGD16 9 ай бұрын

Thanks for the recommendations

@calebmarsters5602 10 ай бұрын

80cc with no limiter gonna go brr

@allmycircuits8850 2 жыл бұрын

At 7:13 it sounds like in Pink Panther's episode "Put-put Pink" which is nice :)

@JGD16 2 жыл бұрын

Thanks for watching! If you enjoyed this, please support the channel by clicking that like 👍button and for more content subscribe and hit that 🔔

@jbstepchild 2 жыл бұрын

Very cool just imagine what could be done with the right gearing for the right job or all round gearing good torqs an good hp ie great take offs an great top speed bet with the right gears could have it doing 80mph but with an assisted take off

@bryanharoldfuller8330 Жыл бұрын

@stepchild , I was thinking that too but you'd have to upgrade the size of the tire Get those fat boy tires and like 29" rims On a normal mountain bike 30 miles an hour is fucking fast and you're hitting speed wobbles Anything faster. But with the larger tires and rims you could easily do 45-50 mph ,I don't know about 80...

@jbstepchild Жыл бұрын

@@bryanharoldfuller8330ols I bike faster than that without a motor but serious your always gonna find the weakest link from vibrations to top speed take offs blah blah blah an sound sound is always an issue

@Alb969 2 жыл бұрын

Sound kurakkan pattumo

@prestonCo. 3 жыл бұрын

Next get a bike with a suspension, mount chainsaw then make a trail video It would be exciting to watch

@bryanharoldfuller8330 Жыл бұрын

Nice 30 miles per hour on the mountain bike that's fucking fast. Any faster you need bigger tires or you get speed wobble probably, But if you get larger fat boy tires Until 29 inch rims, I bet you could do 45 -50 mph no problem

@someonesomeone9991 Жыл бұрын

what chainsaws/engine size and power would you recomend for this?

@JGD16 Жыл бұрын

I used a 51 husky the bigger the engine and the clutch the better off you’re going to be. With a smaller engine you’re gonna have to gear it down a lot which in return you will lose top speed. I also use some electric chainsaws which are a pretty good option 80volt chainsaw e-bike ⚡️ kzfaq.info/get/bejne/rK9iqdCH19i-hmQ.html

@l1nked16 2 жыл бұрын

Hey I have a problem so I welded the sprocket on the outside of the clutch and I’m using the stick 7 speed on my rear wheel so when I hooked it all up I couldn’t pull start it unless I lifted the back wheel up because it was to hard because of the chain so I had to lift the back wheel up but when I did that the chain fell off cause it was loose, do you think that’s cause I need a chain tensioner?

@JGD16 2 жыл бұрын

Two parts to a centrifugal clutch. The inner mechanism connects directly to the engine crank and the outer piece spins freely. the free spinning one is where the sprocket should be connected. As far as a chain tensioner if you have a very short amount of chain you can get away with no tensioner but if it’s a long length of chain you definitely want a tensioner

@mattparker9726 2 жыл бұрын

that's pretty dang awesome! I wonder what you could do with a 66cc 2 stroke kit from China?

@bengrinberg7042 2 жыл бұрын

Ive got a 92cc Stihl 660 clone I'm going to use to make a bike, hope it doesn't maim me

@slender1357 Жыл бұрын

@@bengrinberg7042 what were the results?

@bengrinberg7042 Жыл бұрын

@@slender1357 the chainsaws carburetor got unreliable I'm trying to get it fixed. But with a 30:1 gear ratio it seems like it'll be a safe ride

@2345bcde Жыл бұрын

Can you set this up too use the gearing on the bike

@bryanharoldfuller8330 Жыл бұрын

@supergoose123 ,Yeah you can actually I'm supposed to link to another video that shows how he did it then just combine the 2 ideas. kzfaq.info/get/bejne/g86JabSLx7XMm5c.html

@milosveljkovic6168 3 жыл бұрын

I have a problem. I made a Chainsaw bike but my clutch smokes and creates a high temperature. Do you perhaps know to what extent it could be a problem. The chainsaw is the same power as yours.

@JGD16 3 жыл бұрын

You should check your drive ratio. That’s how many times the clutch spins per one revolution of the wheel. My bike is running close to 20:1 and the clutch seem happy. Anything lower than that you need to change the sprocket sizes and or install a jack shaft.

@idfk223 Жыл бұрын

what if you got a really small sprocket, and hooked it up to the derailleur?

@JGD16 Жыл бұрын

You could do that but the bike would not takeoff very well and you would probably burn out your clutch pretty fast. Most important thing is the gear ratio you want the engine to turn over roughly 20 times for every one time the wheel turns that seems to be the sweet spot for my chainsaw.

@JGD16 Жыл бұрын

@grassygrandma Жыл бұрын

What makes this one better than when you had the chainsaw all on the left side of the bike?

@bryanharoldfuller8330 Жыл бұрын

@Oliver Ries , more balance being centered Rather To the left or right of the frame, Would be my 1st guess Then having it behind the seat compared to in between the frame above where the Pedal sprocket was Reduces the chance of burning your legs Or Heating up your nuts.