I HATE INTERMITTENT FAULTS! SOMEBODY HELP ME!

I HATE INTERMITTENT FAULTS! SOMEBODY HELP ME! | Life of a Mobile Mechanic

Рет қаралды 22,932

8 ай бұрын

Dark days are coming, just like how I felt with this last job!
We first started with an 2003 F9Q Vauxhall Vivaro. The vehicle was showing symptoms of many many things including faulty EGR, Faulty Injectors and the worse one of them all, intermittent start. This puzzled us. I thought it was the injector but it wasn't! Diagnose it once, and diagnose it correctly. Our customer is hopefully going to have the injectors done at some point!
We then replaced brake disks and pads for this Vauxhall Insignia. This one was definitely MY FAULT. My old ways is now finally hunting me down!
Now, the best job of them all, Audi A4 in for a 'faulty' Blower. Unfortunately with this one, it wasn't faulty when we arrived. We tried to replicate what the customer said, nothing; we tried 'bench' the blower motor, nothing. We tried many things, nothing.
The custoemr will then be in-touch again for us to go back for when it gets worse. If you have any suggestions on what it MAY be, please leave it in the comment section
Kingbolen K7 : amzn.eu/d/drm01ZW
Kingbolen Website: kingbolentool.com/collections...
Please like, comment and subscribe to see more contents like this!
Thank you for watching!
If you have any enquiries, or want to get a quote for a job, please send us an email on admin@marvelous-cars.com or visit us on
www.marvelous-cars.com and fill in our enquiry form.
Follow us on:
Instagram: marvelouscarsmobilemechanic
Tiktok: marvelouscars
www.marvelous-cars.com
2003 Vauxhall Vivaro Diagnostic | Vauxhall Vivaro Crank No Start | Vauxhall Vivaro Struggles to Start | F9Q Struggles To Start | F9Q Intermittent Start | Vauxhall Vivaro Intermittent Start | 2003 Vauxhall Vivaro Crank No Start | Renault Trafic Diagnostic | Renault Trafic Crank no Start | Renault Trafic Struggles To Start | Renault Trafic Non-start | Vauxhall Insignia 2012 Rear Brake Pads Replacement | Rear Brake Discs Replacement | Vauxhall Insignia Rear Brake Disks Replacement | Vuaxhall Insignia Rear Brake Pads and Disks Replacement | Audi Diagnostic Fail | Diagnostic FAIL | Audi Blower Motor | Audi A4 Avant Blower Motor Not Working | Audi A4 Not Blowing Air | Audi Not Blowing Air | Audi Not Blowing How AIr | Audi A4 Not Blowing Hot Air VLOG | Lifestyle VLOG | Mobile Mechanic

Пікірлер: 117

@HenryHoover187 8 ай бұрын

16:02 customer is turning the radio volume nob thinking it’s the blower control 😂

@MrXyzasdf 7 күн бұрын

@9:48 Bendix is an American company. All drum brake systems in today's modern passenger vehicles are base on the 1950s Bendix design. In the U.S. Bendix is a tier 1 supplier and I've used brakes pads from them without issue.

@gavTFSi 8 ай бұрын

All variable speed (electronic climate ) VAG fans use current detection when starting, if the control module detects overcurrent it isolates the fan. Once the behind dash area warms up the motor can then work on subsequent starts. They suffer sticky bearings / brushes when old.

@Samanthahodgins 8 ай бұрын

Another great video from Marvelous! ✨

@brianhume4743 8 ай бұрын

Brilliant video again 👏 just saying from North of Newcastle 🇬🇧

@mossiejonas8534 17 күн бұрын

As for Bendix brakes, I have never used them myself but look what I have found...

@Donkeys_Adventure 8 ай бұрын

A4 will need blower motor chances are brushes are worn down, and they stick intermittently.

@alanearls1282 8 ай бұрын

The blower motor behind the glove box in all VW Audi Skoda group develope an intermittent fault, had to replace mine 2 weeks ago, 100% it's the motor

@rizla6220 8 ай бұрын

Hi, Keep up the good work :) I do like these HVAC issue's (NOT) In your case I would check Fan relay then both temperature sensors, then I would be checking the switch gear.

@Lurkajol 8 ай бұрын

Once this happened to a friends Vauxhall Vectra, owner kicked it at got it going again for nearly half a year, it had gotten moisture to the bottom of the blower motor and the drain hole in the motor was clogged. The moisture made a mess of the brushes and the motor burnt out.

@GC_6 8 ай бұрын

I’d recommend inspecting the blower motor resistor. Could be on the way out but best to wait for complete failure instead of jumping to conclusions or you’ll be chasing your tail

@Flishlakv2 8 ай бұрын

I’m sure you don’t need to put the brake into service mode on these Vauxhalls as the e brake is not on the calliper it’s a motor that pulls on the handbrake cable. Regardless great vid and excellent knowledge keep up the good work ❤

@renebox4609 2 ай бұрын

Definitely blower motor. Common issue. They develop a mind of their own when they go bad. Replaced mine recently as it would only work when it felt like it.

@mikee081 8 ай бұрын

The brake pads might have been cheap, but the other 3 pads were perfectly fine, the knackered one just got hot from being seized and started to fall apart. Mintex Ceratec grease is what you need, I've used it for years 👍

@themarvelousvlog 8 ай бұрын

You saw the other pads, right? The material was falling apart. Don’t think that one was due to heat soak 🤔

@keith2507 8 ай бұрын

Love your videos they have saved me a few quid being able to do some repairs myself thanks to your videos. I would like to see a more professional side to john with more input on the videos

@Arounadabout 8 ай бұрын

This channel doesn't show how to do repairs it's a follow me as I work type of channel

@themarvelousvlog 8 ай бұрын

I will make another channel to show repairs. Just depends on difficult it will be in the case of editing etc…

@keith2507 8 ай бұрын

@@Arounadabout it’s a good watch along as I have done basic repairs myself through watching your channel that I otherwise wouldn’t of attempted

@bobdring8857 4 ай бұрын

Intermittent problems need a different diagnosis method. I come from mainframe computer repair and this is how i would attack your problem. Im just DIY with cars… 1 what could the problem possibly be? What can’t it be? 2 if it could be either the fan or the resistor replace the cheapest one and wait for recurrence. Then at least the customer got something for the money. And next time it happens you know what it isn’t. 3 temporally attache an indicator light to the motor and get the owner to observe it when it fails next. Move the light if needed. Even so, I have an intermittent can bus fault at the moment and it has got me struggling. It been OK now for a week but last week it faulted with loads of U type dtc’s several times a day for days. Only happens on the road not in the driveway… especially after rain…

@melpunks5797 8 ай бұрын

New subscriber here. Love learning new shit.

@duxmyman555 3 ай бұрын

I had an Audi A3 with the same problem. get in and no fans. sometimes a good whack under the glove box was enough to get it working again, but eventually changed the blower motor and all was good.

@breakz187 8 ай бұрын

Maybe final stage resistor for the fan? Get the same on BMWs. Can start acting up, then goes full poweere or just stops randomely.

@froilandmarqueses3489 8 ай бұрын

Corrosion or bad solder on the blower fan resistor, at times you'll start losing different blower fan speeds.

@BB.33 8 ай бұрын

Replace blow motor and resistor together, common issue when working in main dealer

@GordonBlachford-ut7ts 23 күн бұрын

Hi great videos, the cost of the jobs would be of interest as the high cost of car repairs varies so much.

@kashkhan6425 8 ай бұрын

I would say that caliper has been sticking, that disc has got hot which then compounds the problem which then I turn causes the pads to stick. I wouldn't be surprised if that happens again on that side, the caliper seals will be shot as they've got too hot.

@rthompson938 8 ай бұрын

Akebono pads are top quality if they do them for that vehicle failing that I always use Brembo.

@tsd550 6 ай бұрын

18:35 “He started kicking under the glove box and it worked fine”. That’s your clue. The carbon brushes in the motor were not making contact with the commutator, probably because they have worn with age. Any physical shock to the motor that is enough to dislodge the carbon brushes, just slightly, so they again make contact will make the motor run again. Further physical shocks almost never make it stop working, only more wear will do that, and it takes time. Sometimes, the braided tails from the carbon brushes are not dressed properly within the motor and do not allow full movement of the brushes as they wear, giving a similar effect.

@themarvelousvlog 6 ай бұрын

Thank you for your help. It hasn’t stopped working since we visited this vehicle last, funnily enough. Owner is still waiting for it to completely fail 😅

@mossiejonas8534 17 күн бұрын

That King bolen K7 is rather fast..!!!

@EZ-D-FIANT 5 ай бұрын

I hate customers picking parts, If Im going to warranty my work im choosing the parts I fit simple as.....👍👌👍

@themarvelousvlog 5 ай бұрын

Always mate 💯

@hardytch8264 8 ай бұрын

it's a Blower motor brush , lots of dust over the time been used build up and loosing connection, that happened on my car 2 year ago , I opened it and cleaned it then started working again till last week stopped again then I replaced happy day.

@themarvelousvlog 8 ай бұрын

Not dusty at all when I checked. I thought that too but definitely not. I will be checking voltages and resistance for when we re-visit

@jeremycanning8934 8 ай бұрын

Check ohms resistance on the motor and resistor to make sure they are in spec. Will be surprised if it's not the resistor

@themarvelousvlog 8 ай бұрын

I will be going back there at some point. Will check on that. Thank you for your suggestion!

@jeremybrambles7992 8 ай бұрын

Sorry to be saying this but from being in the motor trade for over 40 years I would like to give you a bit of friendly advise. Never use wd40 on rubber parts as you did on the the dust seal to lubricate it as wd40 tends to make the rubber swell up causes it to deteriate which then defeats the seals purpose. Regards jeremy

@Kendoddsdadsdogsdead532 8 ай бұрын

Agree.....i made the mistake of putting WD40 on a caliper i was trying to wind back. It killed the rubber.....it swelled up. I had to put a new caliper on in the end so no harm done. Each to there own anyway.

@volt8684 8 ай бұрын

Oh bummer I’ve used it on my rubber sun roof seals for year wonder if that’s why they leaked. Thanks

@johnjacob6570 8 ай бұрын

I would agree but all depends how quickly the rubber is cleaned after the oil application , rubber soaked in oil for long period of time 100% yes

@Arounadabout 8 ай бұрын

Wd40 will dry out rubber and cause it to split

@andrewthompsonuk1 8 ай бұрын

Skope voltage accross vs current on a long timebase and wait for it to fail. Volts and no current means bad motor or the motors connection.

@MrDaniPak 8 ай бұрын

Can you guys move to Toronto?! My car needs fixing, by good mechanics!! lmao

@michaelmcgrath4348 8 ай бұрын

final stage resistor for the fan

@clarky4492 8 ай бұрын

You can get cut conduit thats good for wiring

@HenryHoover187 8 ай бұрын

11:16 two bob uncle roger…. 😂

@razvanturcu9871 8 ай бұрын

The thing with this king bolen is that you won't get bidirectional control with it, unless yoy pay 50$/ year for each make. So, if you are a mechanic, it is not worthy, because it gets way more expensive than more capable scantools (50$ × 7 makes= 350$/ year)

@hosiemali4562 8 ай бұрын

My friend on the insignia it not the cheap pad to be worn that made it wear like that, It's the car wash using wrong chemicals The car wash chemicals, stays in the brake pad friction materials It takes a very long time to dry, specially if you are not driving the car much So it's not your fault

@clarky4492 8 ай бұрын

I reckon thats the resistor breaking down

@andrewhurden 4 ай бұрын

Blower motor for sure

@leewright6101 8 ай бұрын

yeah resistor pack failure, or motor brushes i has same issue turned out it was motor had failed, but do easiest first,, resistor pack if still does it ,, brushes on motor have failed,

@silverfox57 8 ай бұрын

The resistors for the fan are suspect. It should work on low and high but not the other settings. Thats how you know its the resistors.

@Kendoddsdadsdogsdead532 8 ай бұрын

Re the brakes......if your customer has driven 16000 miles pretending to be Lewis Hamilton then those old brakes look about right. It's the heat that kills them..... Poor drivers cause early component failure as well as poor quality parts. They usually go hand in hand. Caliper is also probs on the way out .......

@aduia4 8 ай бұрын

Resistor for sure on intermitted operation

@scwarzewaffe85 8 ай бұрын

Could that intermittent blower be an issue with the loom connector at the blower resistor?

@SteveN-pw4dj 8 ай бұрын

My diesel car with the DPF stripped out produces less smoke than that.

@Tubecraft1 8 ай бұрын

Motor brushes most likely good work

@breakz187 8 ай бұрын

Look at the state of that battery voltage!

@themarvelousvlog 8 ай бұрын

Only because its actuating the pistons but yeah, its under 12V 🥲

@MaxMoment2023 8 ай бұрын

Blower motor resistor gone bad

@martincraig-je4vo 8 ай бұрын

Blower motor needs changing 👍

@pauljones-gt3fn 3 ай бұрын

Any idea what would cause strong diesel smoke on start up for about 20secs, also sometimes difficult to start on cold mornings, 2008 transit connect tdci No faults logged in the system

@froilandmarqueses3489 8 ай бұрын

I didn't quite see in the video you pumping the brake pedal to set and align the caliper piston with the inner brake pad before the re-cal. Failing to do that can cause the misalignment and brake pad to kink, maybe have cause the Bendix inner pad to have the type of wear you described. My experience with these types of brake systems the aggressive wear on rear brake pads is sometimes caused by the active stability control(traction control), where via the ABS activates the brake calipers. It's a combination of the driver's driving style and design, as the traction control is designed to wear the pads so manufacturers can sell more parts(for inexperienced driver's safety). I'm a mobile mechanic myself and I've been in the industry for 17 years... I enjoy your content and keep up the good work.

@thindo 8 ай бұрын

What did you do to John.... He looked happy the whole video 😅😅😅...

@clarky4492 8 ай бұрын

Do you have a relay tester they may test that better as it keeps latching them etc and will detect a fault better?

@ALs_Autos 8 ай бұрын

Those insignias eat pads mate, I worked at the dealer when they were new and it was a daily occurrence changing them

@m60kaf 8 ай бұрын

And the right too, which always seems strange

@Aidan-LM02 8 ай бұрын

That van should go into the ulez zone definitely ulez 😂😂

@themarvelousvlog 8 ай бұрын

I had to make sure!

@Aidan-LM02 8 ай бұрын

@@themarvelousvlog😂😂 old vivaro sadly won’t be compliant

@themarvelousvlog 8 ай бұрын

Don’t even think it will pass LEZ 😂

@Aidan-LM02 8 ай бұрын

Definitely not

@mossiejonas8534 17 күн бұрын

Is Bendix any good? bendix pads are just as good as any other brake oad out there. My friends dad is an engineer for bendix, He knows a TON about brakes, they have a nice aggressive pad which works wonders and never have any noise.20 Jan 2006

@onesies101onesie8 8 ай бұрын

could this of been my issue i had on a w205 c class 2.0 56k miles......? p001685 takes and extra secound to crank and a slight smell on petrol in the oil? runs fine.

@christophergraham9726 8 ай бұрын

If all electrical supply test on a4 blower motor pass . Then id recommend pulling blower motor out and replace with new. classic sign of worn brushes when you give it a whack, and it starts up. assuming all connections are tight and free from corrosion. sometimes you just have to make the call.. Loving your channel, wish i had your energy.

@Aidan-LM02 8 ай бұрын

I used eicher pads on a car the other day the quality was cheap but the customer wanted the cheaper option we normally fit Pagid or brembo

@themarvelousvlog 8 ай бұрын

If they don’t ask for the ‘cheapest’, straight Pagid/Brembo

@Aidan-LM02 8 ай бұрын

@@themarvelousvlogI agree it’s always Mann Mahle Bosch

@jameshakizimana9831 Ай бұрын

Tell me about it bruv. Same here I have an annoying intermittent noise whenever I release the clutch pedal. Funny how on the days I switch off the radio /music in the, try hear the noise, that day, night or morning drive, I won't hear it at all. It happens once or twice in a week, 4 day's maybe, or some days it doesn't happen at all. Any idea what it might be bruv?

@lilseezy8123 8 ай бұрын

Have you tried turning it off and on again

@Aidan-LM02 8 ай бұрын

I’m sure elec parking brake are push back

@burningsoul1365 8 ай бұрын

id check motor carbon brushes and resistar

@Badger66 8 ай бұрын

We all hate intermittent faults!!! Absolute infuriating little buggers!

@combatkiller7881 8 ай бұрын

You are wrong and i feel the need to correct you about using BENDIX brake pads. Im not going to go into too much detail about but ill try and keep it brief. I live in Australia and bendix was a well known and used brand here and i had discovered because of this a lot of counterfeits were out there on the market. Even legitimate companies would supply fake bendix parts without realizing it. I new a spare parts guy very well and he would sell me at the time 2000'sh era a pair of front bendix brakes for roughly $80 to $120 depending on the model of the car. Someone told me that there was a spareparts shop that sold top quality parts for very low prices, so i went to check them out and this is what i found. My friend the spare parts guy would sell me these pads for $90 something dollars and this place would give me the exact same for roughly $35. To cut a long story short, i told my friend this and he was shocked, so he started his own investigation on how it was possible. He and then I found out that they werent proper bendix bads and they were a counterfeit pads, my friend said he contacted the main supplier in Australia or head office of Bendix and it turns out that this was a huge issue and was aware about counterfeits entering the black market. There were small tell tale signs on how to tell the difference, like the logo wasnt printed right, the shade of blue was very slightly off, etc... All i know is that we couldnt spot the difference and we thought this particular shop was somehow getting these pads off the back of the truck, so to speak. It wasnt until speaking with the official bendix person that we could tell the difference. ive been out of the game since 2010 so i dont really know how bad it is now, here in australia with counterfeiting, but perhaps you just was unlucky and got either a faulty or counterfeited bendix brakes, as i have been buying them all my life and have never ever had an issue with them at all. but here in Australia they are expensive.

@sheffcitys2forgedinsteel255 8 ай бұрын

Brief, 🤬ing hell that's a script ( laughing )

@combatkiller7881 8 ай бұрын

😃@@sheffcitys2forgedinsteel255 yeah kinda got carried away

@imapadlock 8 ай бұрын

I’m watching this video, let’s just say.

@FromMetayou 8 ай бұрын

Using the gizzmo to re program brakes does that mean a diy,er cant do there own brske pad chsnge any more without diognostic tool

@stephengolds9679 8 ай бұрын

Blower motor switch?

@jesseplaylist 8 ай бұрын

Be nice to know how much you charge for these brake jobs that are a pain.?

@robsmith7430 8 ай бұрын

Simple lesson, don’t use copper grease on anything that moves and you’ll be fine 👍

@volt8684 8 ай бұрын

Can u say why, when I worked in motor vehicle at college they advocated mucho copper grease on brakes except sliders to prevent squealing, thanks in advance

@robsmith7430 8 ай бұрын

@@volt8684 as you have said what happens to copper grease after a while it turns back to metal essentially due to movement so I’ve been told whereas just on a nut and bolt it’s fine

@themarvelousvlog 8 ай бұрын

The reason why IMI and other institutions is releasing new courses/refresher courses is because of new findings. It’s likely that colleges are still using old findings. Best to have refresher course every 3-5 years just in case. I’ve taken a whole lot now and to be honest, because of it, I’ve saved myself time for following new guidance

@robsmith7430 8 ай бұрын

@@themarvelousvlog forgot to say absolutely loving your channel and learning a lot from you 👍

@billysalter8734 8 ай бұрын

Actuator motors on Audi are shit mine dose the same

@marcparry2131 8 ай бұрын

What do you use instead of copper grease?

@themarvelousvlog 8 ай бұрын

Ceratec by Textar/Pagid/TMD. Actually made for brakes

@marcd7463 3 ай бұрын

I wont fit customers parts full stop

@motiejusselenis5598 8 ай бұрын

what do you use instead of copper grease?

@themarvelousvlog 8 ай бұрын

Ceratec by Textar/Pagid/TMD. Actually made for brakes

@christopherwilson4003 8 ай бұрын

So did you give this customer some money of for using cheaper parts last time .and causing this problem...?

@scorchio70 8 ай бұрын

Came to the comments to see if this has been asked .

@jasperbarlow2582 8 ай бұрын

Auto electrician, i realise you know your stuff, but sometimes a fresh set of hands can help, i ,m ok with mechanicals, but electrical faults can be frustrating.

@pammy5260 8 ай бұрын

Why are electrical faults more frustrating when this is what you specialise in?

@jasperbarlow2582 8 ай бұрын

I was recommending an auto electrician at the very beginning of my reply, i don,t specialise in electronics, i myself am a motorcycle (AND occasionally a car) mechanic and thankfully, encounter very little electrical problems@@pammy5260

@RedStar89 8 ай бұрын

I want a LETS' JUST SAY T Shirt

@themarvelousvlog 8 ай бұрын

Hahaha! That’s coming. I’ve noticed I say it A LOT!

@joncooke479 8 ай бұрын

could be the brushes sticking, could be the wiring connections back to the fuse board . you have to get out of the van and apply yourself

@waynelittle5583 8 ай бұрын

No sound bud

@themarvelousvlog 8 ай бұрын

This is youtube. Wait about 30 mins. Sorry!

@offbeatwarble 8 ай бұрын

@@themarvelousvlogsound working now

@simplemechanics246 4 ай бұрын

You made bad job and customer did not service the brakes yearly. Yes, these need every year service, even if pads and discs does not need the replacement. Nobody cares, that is the result and it can kill easily somebody

@iancarrier-pd8cu 8 ай бұрын

You don’t need a scan tool to release electric handbrake on insignia. You talk bollocks the calliper is clearly sized why hasn’t the other side worn the same? Also a faulty cam sensor would not make a vivaro smoke like it did obviously the injectors are fxxked