Pete swearing in front of glen’s customer 🤣poor old mrs bouquet 😆😆

Thanks for the shoutout Pete !! What a way to end the weekend 🔥🤝 I only install like I do after seeing PB’s work years ago so all credit to this guy .. like this video for me everyone 👍🏻

@ pb plumbing. If you fit a small cutting of 4” pipe into the bent pan connector (size of slip) then put the pan connector into it. It will seal a lot better than just rely on the fins of both pan connector to make the seal

I love the way your pal was using the torch on his phone and then light on the Impact driver to look at the waste. Can’t you get him a few discount Unilite products. Brilliant pipe bending on the job with Marcus.

It's a pain in the ass, but found even more leaks if you stand in the shower and run the hose round. A bit of weight in the shower can reveal a whole lot more sometimes. Great vid this week as always Pete. & Marcus.

Your videos are still far better than any other youpube videos 👍👍👍#❤️❤️PB

Another Sunday and another great vid from Pb keep up the great work my man

Loads of pheasants in that field. 2 peasants in that van . 😂😂

Good video peter one of your best. The pipe bending was awesome.

A snapped screw nightmare when fixing back ..makesure you remove before fixing back guys...good videos chaps

Great content again Pete. Interesting to see that direct thermal store. Haha loved the old cheque story. I had this once and got them to makr it out to my wee girl.

Great vid again Pete! A nice long one, sweet!! I genuinely look forward to the P.B KZfaq notification!! 🥰👍🏼

I love you neat and clean your pipe work is my brother. Awesome work!

Our community is better because you’re in it.

Great as always. About time P.B brought out his own T.shirt range. I would buy one. Nice to see Marcus back again doing all the work again lol. Only joking before people have ago at me P.B always is doing some think or going some where. Well done all

Great video this week PB! I’m actually on the HHP video! He’s an awesome guy 👍🏻 so thank you 👌🏻

Marcus complained about overflow not been piped anywhere then fitted the toilet back the same way. It could have been piped into the top of the toilet pan bend with the other pipe

Very nice low loss header set up on the last job with the leak. The grounds remind me of the places my father took me to growing up while he was looking after homes like that.

Nice jobs Peter well done mate 🙂❤️👍🏼

Top video absolutely brilliant watching everyone made my Sunday 👍

Thank you for helping out bro

Great job 👏

All about the gains🤣🤣🤣 great video mate

Marcus seems quite proficient with lube! 🤣🤣 PB to Milady....so yeah, this is where the water will piss out! 🤣🤣🤣

Great boiler room there. Such a great way to do a large system. It would be class if you had time if you could do a drawing of that boiler room to show how it works just in case I get a job like that to work on! Top level work as always

I’m from the states, it’s great seeing someone bend pipes like like wish we can do it here more often

Couldn’t you of cut the old bent pan con and fitted a bent flexi 1 maybe I’m sure they do them ? 💪🏼👍🏻 love the work PB guns for days 💪🏼💪🏼🤣

Great work lads 👍

I watch these vids each week without fail. I'm not even a plumber! Make me feel like I'm doing a bit...

Screw the KZfaq trolls Pete. Great video again 🤟

Close couple pan can be a nightmare and those fortic combination tanks when you trying to change the ballcock and it’s close to the ceiling happy days

Pete, Love where the Propane is stored 🙈🙈

Pete the word is not piss out, its cascades and pours out " dear boy"!

Got 2 knicks on my fingers . 48 hours later was getting my skin scraped off to the tendons and wrapped up in bandages to prevent sepsis.One was a small knick and one was a wet wooden splinter.

Looks like is stainless/inox coming out, we're told not to put compression fittings onto it since it doesn't bite properly into it. We press onto it. That's how it's here in Denmark anyway

Yes! Shout out to Nick, fantastic electrician who’s literally up the road from me.

love the wee bit at the end 😂😂😂 It's so true with the older generations you try to do them a favour and the next thing you have a check for £10/£20 🤣 It costs more to drive around trying to fine a frigging bank nowadays 🤦🏼‍♂️

Internal overflow and that syphon in the first bit

Another wonderful video! Always good to see Marcus too :) By the way, was that lady in the huge house just waiting around the corner to comment on everything?

You are a brave man I would be a bit nervous on screwing clips onto the side of the cylinder pete

Just subscribe. Love the work. I am also a plumber. Self employed like yourself. Love how I can relate with all the bullshit that comes with the job. My favourite is oh just why your here could you just. Hahaha. Or when people reckon a boiler service will fix there crap heating system or boiler fault. Or when they ring to say ever since you’ve been my toilet doesn’t flush and you fitted them a new rad. Tough job this plumbing lark

Well, I guess that's the advantage of our north American electric water heater. There's 2 pipes, both above, with flexible connectors. Your average home owner can easily unscrew the flexible pipes, roll the thing out and roll a new one in.

Here waiting for the unvented discharge police 👮‍♀️ 🍿 😂

The dream team 😃

Fascinating episode and even more than usual that I felt compelled to comment! Great work filming the lengths you go to for the bends in all the copper pipe - this is not a skill and confidence level every qualified plumber will have! Rip all that push fit waste out it should be banned it is so subpar it's unreal! Thumbs up.

Haha I’ve worked in that big house along time ago when I used to work for someone . The copper work in the floor in the w.c / boot room had all pin holed in the floor replaced it all

Nice weigh in.

good skill toilet out no damage mega neat heating system happy customer nice to do it properly good show this week I am instructing apprentices i will recomend they watch and follow PB

Nice vid - you recommend those Gledhill Stainless ES cylinders? I was thinking of getting one of me old combi gives up the ghost. Nice of you to work on that plumbers mansion ;)

Ask Glen to treat himself to a torch 🔦 😂

37:02 that shit cracked me up lol what the-

Hey PB, happy new year sir to you and family, what brand thermal store is that towards the end of the video, thanks mate

Fans in flats are like torture devices 😫

хорошая работа

Lol, Gordon off Thomas the Tank Engine.😂😂

The first job- unvented cylinder …. Was a 300mm vertical drop before bend after tundish achieved ?😂 looks tight

Can you do a video on how pipe bend the complicated bends like these

54 mins! must have been a bad week lol

Nice one lads,hope you used stainless screws on that cistern so the next guy dosnt have the hassle....cheers

Marcus has the brains pete has the brawn 😂 What’s the rules on connecting a tpr to a soil stack as I thought it had to be proven to be capable of high temps. Asking as i never thought of doing this

Thant's me, paying by cheque from now on.

Dear Sir I just wanted to ask your opinion on wether it makes financial sense installing a heat pump if your refurbishing a property and installing underfloor heating or should i go for a boiler?

Mate if I was built like u I'd d work without a top on 🤣🤣 never too tight unless you have a beer belly and the bike holder hanging out the back

54:29 LOL, so fucking true and you don't wanna say I i will pop by tomorrow and pick up the tenner instead, putting her on an errand to the post office in the morning.

Hi, if the cold supply is 15mm income mains can you achieve enough flow of water for a direct electrical heated unvented cylinder? Thanks

49:28 Pheasant feeder.

Which lever valves do you prefer to use?

Great video Pete. Do you go round working for other heating companies every day or something? I’m confused lol

£££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££££ in the MANSION

marcus straight man

That's the kinda house you should be living in Pete with all your business as a plumber.

15:00 vein on bicep 🤣🤣highlights

Awesome work Pete!, how do you get away with running relief valves into pvc pipes and into the toilet connector? If we did that in New Zealand we’d be raked over the coals for that, we have to run the relief drains in 22mm copper outside over a gully 😊

Fantastic so much good stuff in this video, Just a quick question how come your press fitting most off your copper now the fittings are so much more expensive ? Thanks 😊

This is my first comment ever but I’ve got to ask , 1 how do you know the cylinder is full being open vent without a visual of the water level , as I can imagine it’s very easy to go over the open vent (since it’s within the cylinder ) and due to evaporation of the cylinder being hot almost continuously wouldn’t the home owner have to top it up from Time to time as it has an open vent, I’m assuming it’s acting like a usual F/E tank without the automatic top up

👍👍

Boys, get ye sen some slipon overshoes so you can keep ye boots on 😜 or a pair of slippers 😂

Ps Austin is a great city and I was there in mid 90s and plumbers could make big bucks there.

With an open wound. “I don’t give a fuck” is classic. Us Americans aren’t much different from our brothers across the pond. ✌🏼

Regarding the t shirts ...as you already mentioned its a tight large or baggy around the wasist x large. Please chose the x large as most men would. You already have a particular vibe and trust me tight t shirts dont help. I really dont mean to be disrespectful.

Do you need a non return valve on the PRV where it goes into the toilet waste? Wouldn't want your toilet flushing into the tank 😂

Good videos. The prv is connected to the toilet pan, but I did not see a trap. Don’t you have an issue with sewer gas potentially coming into the cylinder room?

Wheres the shotgun when you need one pheasant for dinner

🤘😎🤘

Super 🇫🇷👍👍🇺🇦💪

Push fit waste under the floor Noooo . Solvent weld only please

Hi. What wall thikness of 15 and 22 cooper pipes you work with? It's 1 mm? Or less?

@ 18:01 ? What did U do 2 resolve the toilet overflow pipe...

Do powerfool mate deliver to Northern Ireland

And that's why i don't do domestic.

Where does the overflow of the reservoir go xD

Soo... where did you plumb the toilet overflow ? Into the pan waste too ? And if so ,was there possibly a pipe dropped away from the original overflow pipework... and if thats so, wouldn't the flat upstairs flood in here if their toilet overflowed ?? I'm not a plumber... I'm here to learn 🤗

Cut through the pan connector extension! No need to take toilet out! Also shouldn’t orb discharge where it can be seen???

THE WATER LINE IS LEAKING ! NOT THE WASTE OR THE SHOWER. if she said its never used its the only thing it can be

It would cost over 13K to fill that oil tank at that big house! What did you do about about the overflow on the bog that didn't go anywhere? (on the unvented job)

What size screws did you put in cylinder?

Hi Pete how come the power tool mate code never works on there site

That type of heating system doesn't rely on room stats?

Is that solvent weld pipe for the PRV pipe? I thought it had to be push fittings only?

If an unvented cylinder, why not set on the floor? 🤔