I have worked in a machine shop in a third world country where we had to do repairs similar to this you do what you have to do to get the thing running again. Although our lathes etc had coolant and we had centre drills etc it is a bit dodgy drilling a hole with a drill poking out that far without using a centre drill first. The finish would have been much better with coolant rather than all whiskery. One of our most common repairs was arc welding conrod journals on crankshafts as they had been worn down so much usually on 1 journal only that you could not buy undersize bearings to suit. I made cyl head valve inserts out of old truck axles. You do what you have to do.

Don't take this video seriously. This is just an entertaining video that shows man's skills. 100 percent this is not an actual repair. Not even that it will not hold but the polishing not done properly. But I personally love watching this videos

Anybody can work with new parts and machine,but job done with whatever you have,is ability of mechanic,tool maker and machinest I salute you sir for job well done

SEMUA MEKANIK SEMUA ENGINEERING DARI PAKISTAN .. JENIUS DAN SMART DAN HEBAT HASIL GARAPANNYA DIJAMIN MUTU/MEMUASKAN + DAN SEPERTI : ASLINYA/PABRIKAN H E B A T TIADA LAWAN A M A Z I N G THE BEST GOD BLESS

Mashaallah nice and neat, job done well

Fire fighting! Great جُگاڑ good workmanship 👍

Done fabulous job 100% good skills

Bravo majstori, to Ameri, Britanci, Francuzi, Nemci i dr Evropske zemlje mogu samo da gledaju.

EXELENTE trabalho de restauração de ponta de eixo Carlos cuiabs

Skilled lathe work, decent looking finished item, to all you armchair precision turners criticizing, yes this could have been done in a different way, but this may be good enough to get the job done.

making the thread for the nut impressed me.💣

Обалдеть: в токарке чистый пол, станок убран - первый раз такое! Но дальше все по-прежнему. Кривой индикатор, сварка на станке, неподвижный центр в задней бабке, сырой приварыш, отожжённый кулачковый вал - всё в банку.

Кулачкам сразу похорошело после напильника. 😂

Кто-нибудь, скажите ему, что повозюкать напильником и наждачкой - это не полировка кулачков распредвала. Это нарезание стекла кувалдой и топором.

Greeting and peace from MOROCCO to these men YAFID MOHAMMED/ KENITRA / MOROCCO /

Good Job 👍👌

Brilliant work

Nice work

BRAVO ! may it last forever .

Buen trabajo, se hace lo que se puede con lo que se tiene. Espero que dure un buen tiempo.

Good job. Sometimes westerners forget that what is available two states away is nothing compared to two or three provinces away...provinces the size of some countries or larger. Bic-lighter "throw away and get another" people have a panel truck delivery from their favorite seal and bearing shop. You make do with what you have to work with. Outstanding skills. Those skills don't have free shipping. They certainly do not have a grade-8 Fastenal shop & watehouse in the next town. The original part and original part replacement is always the best. Better than this reworked part. Westerners can go get it like buying chewing gum. Of course this is not going to last as long. Yes it will break again. But you know what, for now it works. For now it gets the owner out of a serious pinch. For now it buys him a little more to enable "free shipping." He still makes a living while waiting for overland express. Good job!!!

Very nice great👍👏😊

Испытал культурный шок.

Amazing work guys. Thanks for sharing. Perhaps leave the original audio in for people who can understand what is being said.

Awesomeness great work as hard as disaster skill ! Respective it .. ❤

Antes era una pieza masiza y se rompió, ahora tiene menos material de conexión por la espiga de ajuste. Seguro se vuelve a romper...

Well trained by experience

un buen trabajo me delecto ver estas persona trabajando

Meus parabéns, Deus abençoe a todos vocês pelo seu belo trabalho, outro dia eu assisti a um vídeo seus em que se recuperava um eixo gira-brequin, aqui no Brasil eu nunca vi um trabalho igual ao seu, e olha que sou mecânico bombista a uns 40 anos. A minha pergunta aos senhores é: a têmpera do material dos eixos (aço) não fica comprometida ? Quando puderem, por favor me respondam. Felicidades a todos vocês.

Interesting to note the colour of the cam lobe after the welding process ((blue..) not to mention the weld spatter. Could this process have affected the original hardness of the cam face, I wonder? Respect is due for a workable short term repair with well worn out tooling! Keep up the good work, boys!

Fantastic work.

It looks good shape after welded and machined. However, it will break pretty soon at the same spot due to weakness of the join causing a disastrous damage to the engine.

Молодцы, при безвыходном положении. А так все это лечение заклинанием гонореи дома на кухне.

Its nice to see a work area that's clean for a change .

siete incredibili , con quel poco che avete fate miracoli ,complimenti😇

Good field work, that's it!!

Un régal de vous regarder "œuvrer"! Merci pour la vidéo!

Mesmerisingly good to watch. Cutting the thread by eye too.

Rolls-Royce could learn a thing or two from these fellas about precision and quality control 😂😂😂😂

Штатный хвостовик отвалился, а приваренный к чугуну отвалится через пять минут. Мастера блин.

Very nice repair using limited means 👍

This is what you do when precision is not a concern.

Very skillful

Much respect.

Well done

Good work

Good job thank you

Center drills are OK to use for work like this. That long series drill hole could be any size.

It’s just beautiful to see the repair work. Grew up in a company that had a lathe machine, and we made almost any thing. This art is being lost due to the cheap manufacturing and sales pitch. Lots of material is wasted by having to dump the broken pieces, either to land fill or smelter. But, it’s the modern world now, progress ent?

EXECELLENT TURNER.

SKILL and TALENT on display for everyone to see. WOW just WOW !!

Good work I like 👍

great job

bravo tornitore anche io li ricostruivo cosi ..........usavo x il comparatore x essere piu preciso .cmq bene cosi lo stesso

Người thợ giỏi lấy được độ đồng tâm nhanh chính xác.

Superb...

I think that dead centre is getting overheated as everytime the cutter goes down that end it's smoking badly! You are meant to use some grease and hold it with light pressure not force it in until it smokes!

C'est le travail d'un bon bricoleur. Un vrai tourneur aurait procédé autrement.

Eso definitivamente se va a volver a romper mucho antes de lo previsto

Пять лет работал токарем, но смотреть как работают другие, интереснее. С центрами в задней бабке таких проблем не было.

😅Finally, a Pakistani workshop that seem neat and tidy.

BRAVO !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Bravo, bon travail

❤شكرا لجهودكم في جمع هذه المعلومات القيمة

Do not be a party pooper ,it will not brake ,the weld is harder than the steel was used. Good job , well done.

Nice bro

Looks like the last repair did not last ,timing spot on correct.

Деталь в музей на полку😊👍

Desde Panamá es usted un maestro en la tornería. Saludos

Excellent Brother.

ingenuity and skill can fix a lot of stuff as proven here!

Bravissimo.

King of the scrap heap, at the most

I had 2 cups of coffee this morning.

Thanks for the video, its a different world out there, methodology is different it works then fine, if it breaks it comes back, more work to keep busy and more money. These are guys who work by experience, Vernier is close so why use micrometer?

Amazing talent ! Thank you for sharing. ❤️

This gentleman has made the best job he could with tools at his disposal. Excellent job all round,

great work.. i wish we had creative and capable machinist in my area that were able to do such quick turn around and i am sure very reasonable prices as you do

I got a double over head twin cam need two of these done. LMAO 🤣

looks good to me

It's like watching red green fix something but with out the duck tape lol

That part won't last long. The weld is always a problem. The seam is harder than this cast steel and the cast steel was not preheated either, which makes it porous and will sooner or later burst. The work has been carried out in a completely pointless and absolutely catastrophic manner. The dimensions must fit to the thousandth or the bearing point will be disturbed. But since the accuracy of the machine is also in doubt, the time is wasted

Excepcional !!!

Good grief, not a micrometre or dial gauge in sight and with their skill can perform such work. Bit hit-n-miss here-n-there but the final result looked promising.

Świetna jest zrobiona ta cała robota pozdrawiam twórcę tego filmiku serdecznie 👍👍👍👍👍

EXCELENTE TRABAJO.

alter Verwalter, wasn Pfusch... Spitzenhöhe ausweija .... Plandrehen ohje......Längsdrehen naja und Bohren ohne Zentrieren.... das kann der Praktikant besser..... und die Späne dunkelblau..alles Super und richtig gemacht ....

Ndoshta do ishte më mirë nga ana teknologjike , të bënte fileto femër ke aksi dhe mashkull ke bishti

عمل جميل جدا جدا وعاشت اليدي

Desenho à mão-livre...

I know they are poor but a centre drill really would work wonders instead of a normal drill to start off. They also seem to not worry about safe practice against body injuries>

best part, puts the file on top of the cam !!! 17:29 omg

¿Cuanto va a durar ese trabajo si el metal ya perdió el templado correcto ?

3 palabras,...Broca de puntos...

That was interesting to watch. They could have used some cutting oil to prevent some of the heating of the part and make it easier to cut, but it turned out OK. The weld rod material is the same as the camshaft so it should hold. I would have started the drilling with a smaller drill to pilot the bigger drill and that would have made it easier to drill out. Nice job otherwise.

Как новая!)))

Excelente, mis felicitaciones 🎉😢

Nagyon ügyesek vagytok. A nyugati emberek már ilyent nem tudnak. Nem javítanak már meg semmit csak kidobják. Újra cserélik. Ez elmondható a párkapcsolatukról is. Régen nem így volt itt sem. A nyugati ember már elfelejtet javitani.

Bravooooooo bravo

Exllant job saves a poor man money.