The King of Mechanic Repaired A Broken Diesel Pump Came-shaft with Using Old Mind.....

Рет қаралды 1,667,557

Жыл бұрын

The King of Mechanic Repaired A Broken Diesel Pump Came-shaft with Using Old Mind.....
#kingmechanicrepaircameshaft
#howrepaireddieselpumpshaft
#pkprocess

Пікірлер: 472

@abduldarr3920 9 ай бұрын

Mashaallah nice and neat, job done well

@khankashif3791 8 ай бұрын

Done fabulous job 100% good skills

@grantreid8583 9 ай бұрын

I have worked in a machine shop in a third world country where we had to do repairs similar to this you do what you have to do to get the thing running again. Although our lathes etc had coolant and we had centre drills etc it is a bit dodgy drilling a hole with a drill poking out that far without using a centre drill first. The finish would have been much better with coolant rather than all whiskery. One of our most common repairs was arc welding conrod journals on crankshafts as they had been worn down so much usually on 1 journal only that you could not buy undersize bearings to suit. I made cyl head valve inserts out of old truck axles. You do what you have to do.

@abduldarr3920 9 ай бұрын

Anybody can work with new parts and machine,but job done with whatever you have,is ability of mechanic,tool maker and machinest I salute you sir for job well done

@albinklein7680 8 ай бұрын

It will not last more than fifty miles and after that the whole pump will be trashed beyond repair. That blue lobe lost its case hardening, will get eaten away by the plunger and the shavings will absolutely destroy the pump in minutes.

@juliabernardes2468 8 ай бұрын

EXELENTE trabalho de restauração de ponta de eixo Carlos cuiabs

@rajaramkajale1659 8 ай бұрын

Very nice great👍👏😊

@tahirrasheed9740 10 ай бұрын

Fire fighting! Great جُگاڑ good workmanship 👍

@miladinrankovic3655 8 ай бұрын

Bravo majstori, to Ameri, Britanci, Francuzi, Nemci i dr Evropske zemlje mogu samo da gledaju.

@donooetomo5213 10 ай бұрын

SEMUA MEKANIK SEMUA ENGINEERING DARI PAKISTAN .. JENIUS DAN SMART DAN HEBAT HASIL GARAPANNYA DIJAMIN MUTU/MEMUASKAN + DAN SEPERTI : ASLINYA/PABRIKAN H E B A T TIADA LAWAN A M A Z I N G THE BEST GOD BLESS

@SuPeRbOmBeRmAn4 10 ай бұрын

making the thread for the nut impressed me.💣

@mikekerezsi9672 10 ай бұрын

Nice work

@philliplopez8745 5 ай бұрын

BRAVO ! may it last forever .

@syedbaquarhusain 10 ай бұрын

Good Job 👍👌

@gvvggvgjj6724 10 ай бұрын

Greeting and peace from MOROCCO to these men YAFID MOHAMMED/ KENITRA / MOROCCO /

@keithgarland3404 9 ай бұрын

Skilled lathe work, decent looking finished item, to all you armchair precision turners criticizing, yes this could have been done in a different way, but this may be good enough to get the job done.

@albinklein7680 8 ай бұрын

No. It will totally destroy the pump in mere minutes if anybody is dumb or crazy enough to install that thing. I hate those fake "repair" videos.

@stevefoley1021 10 ай бұрын

Brilliant work

@TheXilya Жыл бұрын

Don't take this video seriously. This is just an entertaining video that shows man's skills. 100 percent this is not an actual repair. Not even that it will not hold but the polishing not done properly. But I personally love watching this videos

@josephgarcia676 10 ай бұрын

Those things are made precision wait balance everything there’s no way this is gonna work, but it is entertaining I get it

@BigMike-tx7uf 9 ай бұрын

Good work

@MrKhurramking 9 ай бұрын

Well done

@ryshaerinna7016 9 ай бұрын

Well trained by experience

@jimwalker3039 10 ай бұрын

Very skillful

@victormedina177 10 ай бұрын

Кулачкам сразу похорошело после напильника. 😂

@fbilgrami 10 ай бұрын

Amazing work guys. Thanks for sharing. Perhaps leave the original audio in for people who can understand what is being said.

@tjsogmc 8 ай бұрын

Rolls-Royce could learn a thing or two from these fellas about precision and quality control 😂😂😂😂

@angageperera247 10 ай бұрын

Superb...

@robertopablovizcarra3023 7 ай бұрын

Buen trabajo, se hace lo que se puede con lo que se tiene. Espero que dure un buen tiempo.

@tarakrohoman7321 10 ай бұрын

Nice bro

@marionboucher3155 7 ай бұрын

great job

@martinclark3140 11 ай бұрын

Awesomeness great work as hard as disaster skill ! Respective it .. ❤

@robbinperers8526 11 ай бұрын

Good job. Sometimes westerners forget that what is available two states away is nothing compared to two or three provinces away...provinces the size of some countries or larger. Bic-lighter "throw away and get another" people have a panel truck delivery from their favorite seal and bearing shop. You make do with what you have to work with. Outstanding skills. Those skills don't have free shipping. They certainly do not have a grade-8 Fastenal shop & watehouse in the next town. The original part and original part replacement is always the best. Better than this reworked part. Westerners can go get it like buying chewing gum. Of course this is not going to last as long. Yes it will break again. But you know what, for now it works. For now it gets the owner out of a serious pinch. For now it buys him a little more to enable "free shipping." He still makes a living while waiting for overland express. Good job!!!

@martinkazako2292 10 ай бұрын

👏

@NeonAstralOfficial 10 ай бұрын

Worth waiting a for a few provinces away, this camshaft if explodes could destroy the engine which is 1000$ more expensive than this part

@BOEHHO89 11 ай бұрын

Its nice to see a work area that's clean for a change .

@mauricelevy9027 8 ай бұрын

He's probably going to knock up a "new" chuck key so He can really knacker His chuck looking at massive abuse the chuck had had . Hitting that poor cam to attempt to reduce run out was hilarious ,also filing to cam lobe Mind You his centre was a real work of at for friction welding. .Sorry ,this is chuck awful practice

@user-je9ke2wt1t 8 ай бұрын

Молодцы, при безвыходном положении. А так все это лечение заклинанием гонореи дома на кухне.

@Clapaskiller 10 ай бұрын

Fantastic work.

@MrLentiscais 8 ай бұрын

Center drills are OK to use for work like this. That long series drill hole could be any size.

@Silverfox1111 9 ай бұрын

Much respect.

@ruberitogusmao7216 Жыл бұрын

EXECELLENT TURNER.

@carlobellucci1196 9 ай бұрын

Bravissimo.

@robertomijango6207 10 ай бұрын

un buen trabajo me delecto ver estas persona trabajando

@user-dw2mn2oi7c 10 ай бұрын

Кто-нибудь, скажите ему, что повозюкать напильником и наждачкой - это не полировка кулачков распредвала. Это нарезание стекла кувалдой и топором.

@gennadiykolomiyets 4 ай бұрын

Це жесть. Художня цінність може . буде ніжка до столика тільки треба пофарбувати .Як запчастина це металобрухт. Распредвал цементований та та закалка ТВЧ. Може це для осла щоб біг краще

@landog59 10 ай бұрын

Good field work, that's it!!

@muhammadejaz9995 Жыл бұрын

Good work I like 👍

@sergiokrm1 Жыл бұрын

Испытал культурный шок.

@mohanddah9194 10 ай бұрын

Bravo, bon travail

@Alex.369 11 ай бұрын

Antes era una pieza masiza y se rompió, ahora tiene menos material de conexión por la espiga de ajuste. Seguro se vuelve a romper...

@Rocketman88002 10 ай бұрын

😂😂😂

@giuseppegalliano494 8 ай бұрын

bravo tornitore anche io li ricostruivo cosi ..........usavo x il comparatore x essere piu preciso .cmq bene cosi lo stesso

@tellyonthewall8751 8 ай бұрын

King of the scrap heap, at the most

@dean825 10 ай бұрын

This gentleman has made the best job he could with tools at his disposal. Excellent job all round,

@adullahsum4773 Жыл бұрын

Good job thank you

@irlanmartinstavares3112 5 ай бұрын

Meus parabéns, Deus abençoe a todos vocês pelo seu belo trabalho, outro dia eu assisti a um vídeo seus em que se recuperava um eixo gira-brequin, aqui no Brasil eu nunca vi um trabalho igual ao seu, e olha que sou mecânico bombista a uns 40 anos. A minha pergunta aos senhores é: a têmpera do material dos eixos (aço) não fica comprometida ? Quando puderem, por favor me respondam. Felicidades a todos vocês.

@houariboubker4459 Жыл бұрын

C'est le travail d'un bon bricoleur. Un vrai tourneur aurait procédé autrement.

@andykeri8370 10 ай бұрын

Do not be a party pooper ,it will not brake ,the weld is harder than the steel was used. Good job , well done.

@SilverSergeant 8 ай бұрын

Laughable.

@yvon501 10 ай бұрын

Un régal de vous regarder "œuvrer"! Merci pour la vidéo!

@padraiggluck2980 Жыл бұрын

Very nice repair using limited means 👍

@v.volynskiy Жыл бұрын

Обалдеть: в токарке чистый пол, станок убран - первый раз такое! Но дальше все по-прежнему. Кривой индикатор, сварка на станке, неподвижный центр в задней бабке, сырой приварыш, отожжённый кулачковый вал - всё в банку.

@X_Killer. Жыл бұрын

Т.е угандоненная станина тебя не смутила?

@v.volynskiy Жыл бұрын

@@X_Killer. Давай так: меня НЕ СМУТИЛ только чистый пол и отсутствие стружки на станке. Всё остальное это одна большая беда.

@X_Killer. Жыл бұрын

@@v.volynskiy 🤝 однозначно категорически поддерживаю Вашу позицию😁

@zeekwolfe6251 Жыл бұрын

😅Finally, a Pakistani workshop that seem neat and tidy.

@robastore9192 8 ай бұрын

Looks like the last repair did not last ,timing spot on correct.

@osvaldorivero4242 Жыл бұрын

BRAVO !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

@butong-ongbut457 Жыл бұрын

Người thợ giỏi lấy được độ đồng tâm nhanh chính xác.

@jackbarrie6007 Жыл бұрын

But he is not good at his job you can't know what is good or bad if you comment like that

@myselfnet5876 8 ай бұрын

Bravo, excelente trabajo.

@aedwards4496 Жыл бұрын

Mesmerisingly good to watch. Cutting the thread by eye too.

@morenonap58 Жыл бұрын

siete incredibili , con quel poco che avete fate miracoli ,complimenti😇

@Crowplain Жыл бұрын

Interesting to note the colour of the cam lobe after the welding process ((blue..) not to mention the weld spatter. Could this process have affected the original hardness of the cam face, I wonder? Respect is due for a workable short term repair with well worn out tooling! Keep up the good work, boys!

@rumenivanovtzonchev4072 11 ай бұрын

Rarely shoddy work. They do not use coolant. The diameter of the welded part was measured by eye, not with a micrometer. Finally he ran the rasper over the friction surfaces of the shaft, which are specially machined to produce a hard layer - he injured this layer. The metal he uses for the extra part is soft and don't work. If he is going to use a weld (which weakens the metal anyway) why not weld the original part? If I had a worker like that, I would fire him immediately

@whitefreeman5798 11 ай бұрын

@@rumenivanovtzonchev4072 yeah here in america we have the option to just buy another pump for a few thousand dollars and bolt it on then hope it isnt junk and thousands wasted with another few thousand wasted at the shop to have it put on.. it works for them and they are keeping equipment going so maybe they are the ones doing things the smart way while working with what they have

@rumenivanovtzonchev4072 11 ай бұрын

@@whitefreeman5798 That's right, but putting in a water pump and a hose to run coolant doesn't cost money. Separately, why didn't they weld the two pieces of the broken part?

@whitefreeman5798 11 ай бұрын

@@rumenivanovtzonchev4072 so they could get a better weld and have more surface area to weld and so it would be the right length

@jessefinneman7680 9 ай бұрын

Many people weld cams for more lift 😉

@robertbutler8004 Жыл бұрын

This is what you do when precision is not a concern.

@MrLittlewasp 11 ай бұрын

the precision one broke too...

@mauricelevy9027 8 ай бұрын

Yes,well it's ONLY a camshaft eh ???

@kriber5154 7 ай бұрын

This is what you do when you want something to work again without having to throw it away.

@user-bb5hy7vz1s Жыл бұрын

عمل جميل جدا جدا وعاشت اليدي

@loisanellivedralev 10 ай бұрын

Eso definitivamente se va a volver a romper mucho antes de lo previsto

@Rocketman88002 10 ай бұрын

😢😢😢

@irlanmartinstavares3112 5 ай бұрын

Saudações meu caro amigo, você acredita que pensei na mesmíssima coisa ? Escrevi para o rapaz, perguntando a respeito da têmpera do material, se não enfraquece a dureza do aço ?

@user-cm6bu3yh4j 11 ай бұрын

Деталь в музей на полку😊👍

@manonwong8742 10 ай бұрын

It looks good shape after welded and machined. However, it will break pretty soon at the same spot due to weakness of the join causing a disastrous damage to the engine.

@benovision6325 10 ай бұрын

Yes that's correct. The cam shaft is a forged metal component with a very definite arrangement of the metallic crystals, nothing of which you will have in a chaotic metal weld! Its doomed to fail and very naïve engineering.

@alexanderSydneyOz 10 ай бұрын

It is not 'doomed to failure', and neither of you two have any reason to say that. Every time one of these videos is posted, there are 100 'experts' saying 'oh it won't work', or 'It'll break', and so on. Well, this is a camshaft. It really isn't subject to much torque, so I see no reason to say it will "break pretty soon". Why would it? Most likely this shaft broke due to some other part of the motor seizing and apply WAY too much torque to the cam in the process. ie atypical forces.

@dmitripetrov5536 10 ай бұрын

This a camshaft, NOT crankshaft . There is not too much stress on it.

@benovision6325 10 ай бұрын

@@dmitripetrov5536 So why did it shear off then. Its a forged part for a reason. Im happy for you to put it in your engine. Maby it should be cast from plastic. Can you give me your torque calculations for the high pressure diesel fuel pump.

@thepubliceye 10 ай бұрын

@@alexanderSydneyOz This cam is out of an injection pump, there is a lot of torque on it. The other issue of intolerance, he just eyeballed the end.

@user-nb7md7jc2g Жыл бұрын

❤شكرا لجهودكم في جمع هذه المعلومات القيمة

@ttinnovations3310 9 ай бұрын

best part, puts the file on top of the cam !!! 17:29 omg

@edgarcornette6387 10 ай бұрын

SKILL and TALENT on display for everyone to see. WOW just WOW !!

@allmysteryangelo01 11 ай бұрын

alter Verwalter, wasn Pfusch... Spitzenhöhe ausweija .... Plandrehen ohje......Längsdrehen naja und Bohren ohne Zentrieren.... das kann der Praktikant besser..... und die Späne dunkelblau..alles Super und richtig gemacht ....

@tonychana1623 Жыл бұрын

Excellent Brother.

@grumpyg9350 Жыл бұрын

I had 2 cups of coffee this morning.

@juderamnarine5617 10 ай бұрын

It’s just beautiful to see the repair work. Grew up in a company that had a lathe machine, and we made almost any thing. This art is being lost due to the cheap manufacturing and sales pitch. Lots of material is wasted by having to dump the broken pieces, either to land fill or smelter. But, it’s the modern world now, progress ent?

@RAMNARESHSINGH-iv8nr 9 ай бұрын

@SilverSergeant 8 ай бұрын

Very inferior strength.

@melockavich9596 Жыл бұрын

looks good to me

@user-bk8fg1mh2e 11 ай бұрын

nice

@chantalrubino337 10 ай бұрын

Precision work in Birmingham UK.

@sheridanbaldwin8629 11 ай бұрын

It's like watching red green fix something but with out the duck tape lol

@miloudibarjane8233 10 ай бұрын

Bravooooooo bravo

@ZuTez2023 10 ай бұрын

Как новая!)))

@renekoesler4704 11 ай бұрын

ingenuity and skill can fix a lot of stuff as proven here!

@albinklein7680 8 ай бұрын

It's not fixed. It's a piece for the shelf. Nobody in this world is crazy enough to install this pos.

@marvstrickler9573 9 ай бұрын

Two little marks past the big mark, with high-polish and deep scratches.

@florenciolopez9312 11 ай бұрын

Desde Panamá es usted un maestro en la tornería. Saludos

@mariodeker1983 10 ай бұрын

Velika pogreška!!!varenje na tokarilici je ne primjereno !!! Krivi naputak!😂😂😂😂😂😂zbilja za plakanje!

@mukhtarsingh4091 11 ай бұрын

Exllant job saves a poor man money.

@royschmidt675 11 ай бұрын

Amazing talent ! Thank you for sharing. ❤️

@GWAYGWAY1 10 ай бұрын

I know they are poor but a centre drill really would work wonders instead of a normal drill to start off. They also seem to not worry about safe practice against body injuries>

@chachacheng9380 Жыл бұрын

Why not use Krazy glue ?

@manarroper 11 ай бұрын

3 palabras,...Broca de puntos...

@leonalfredourzolaestrada4760 Жыл бұрын

EXCELENTE TRABAJO.

@alexdeggel8767 Жыл бұрын

Штатный хвостовик отвалился, а приваренный к чугуну отвалится через пять минут. Мастера блин.

@rumenivanovtzonchev4072 11 ай бұрын

Я редко видел настолько некачественную работу. Они не используют хладагент. Диаметр свариваемой детали измеряли на глаз, а не микрометром. Наконец, он провел напильником по фрикционным поверхностям вала, специально обработанным для получения твердого покрытия; этот слой был поврежден. Металл, который он использует для дополнительной детали, мягкий и не работает. Если он собирался использовать сварку (который в любом случае ослабляет металл), почему бы просто не припаять оригинальную деталь? Если бы у меня был такой работник, я бы его немедленно уволил.

@user-mh8xk3lt5z 11 ай бұрын

Штатный уже был сделан по такойже технологии!😂😂😢

@mikhailbudnikov 10 ай бұрын

Судя по зонной закалке, стружке из под резца это всетаки сталюка❤

@GjergjiNNikolla1952 11 ай бұрын

Ndoshta do ishte më mirë nga ana teknologjike , të bënte fileto femër ke aksi dhe mashkull ke bishti

@bignasty3274 Жыл бұрын

I think that dead centre is getting overheated as everytime the cutter goes down that end it's smoking badly! You are meant to use some grease and hold it with light pressure not force it in until it smokes!

@Watchyn_Yarwood Жыл бұрын

Amen bro!

@aussiehardwood6196 Жыл бұрын

Nah.... that's the way they do it in India, they get chit done...and its cheap.

@Fellafoe69 Жыл бұрын

thats normal as the machining makes the material bloody hot with no coolant

@bignasty3274 Жыл бұрын

@Gringo! I do a lot of turning, and not once has the dead centre overheated like that!!

@Andrew_Fernie 11 ай бұрын

It's the first time I've seen anyone put a drop of oil on the centre, nevermind HP grease.

@andrzejporeda7281 Жыл бұрын

Świetna jest zrobiona ta cała robota pozdrawiam twórcę tego filmiku serdecznie 👍👍👍👍👍

@domingosneves3179 11 ай бұрын

Desenho à mão-livre...

@358oleg. 19 күн бұрын

У них таких роликов много,это заработок а не ремонт.

@jorgefernandez-mv8hu 5 ай бұрын

That was interesting to watch. They could have used some cutting oil to prevent some of the heating of the part and make it easier to cut, but it turned out OK. The weld rod material is the same as the camshaft so it should hold. I would have started the drilling with a smaller drill to pilot the bigger drill and that would have made it easier to drill out. Nice job otherwise.