Timing belt replacement 01 ford focus 2.0 zetec dohc

Рет қаралды 64,953

Spank Tank

7 жыл бұрын

Timing belt

Пікірлер: 39

@MrWhitey1010 2 жыл бұрын

Just watched your video on the ford focus timing. Finally someone who will give you Good tips without explaining there while life story first. Thanks brother

@peterdatechmen5506 5 жыл бұрын

Nice to see a diy job done as when we techs post we tend to show an easy job, but this depicts the few struggles you get when new on the job and its not a daily task.

@fundaandkady 5 жыл бұрын

I’ve used him for a 02 Audi A6 and she’s running perfect

@tyronemillions4794 Күн бұрын

My buddy did a head gasket and the block is top dead center but the head is not. I’m not sure how to adjust the head to top dead center

@EdwardHomerVIC 4 жыл бұрын

Great video thanks. When you order the timing belt kit from Car Whiz do you get the special tools needed for the Ford Focus? I don't see them listed. Do you order them separate, can't find them listed. Thanks.

@spanktank6582 4 жыл бұрын

Oh yeah I brought the tool off eBay it a Ford timing tool

@TheCoatneyadkins 6 жыл бұрын

what kinda gear wrench was that you used on the crank bolt to turn it? look nice

@spanktank6582 6 жыл бұрын

TheCoatneyadkins its a duralast combination wrench from AutoZone

@firstnamelastname-ed9zz 2 жыл бұрын

Put some respek on my name!! Sound like Birdman.. damn good video!

@piscesmikey 7 жыл бұрын

Do you run a shop in Durham, NC? You sound exactly like the guy who did the EGR on my crown vic. ..

@kurtiscal3msetccdwell618 5 ай бұрын

Do you put the engine at TDC on the 1st cylinder compression stroke or did you worry about that?

@spanktank6582 5 ай бұрын

Yes u do I already did before I make the video I'll just showing y'all how to but that year was a non Inference engine

@johnchapman1767 4 ай бұрын

Is the 2002 2.0l dual overhead cam a interference engine

@jacobdavidcunningham1440 4 жыл бұрын

3:24 oh yeah...

@williamvest8581 5 жыл бұрын

do you have to move the cams if you not doing the seal? I have a 02 ford focus 2.0 dohc se wagon

@spanktank6582 5 жыл бұрын

No you don't

@williamvest8581 5 жыл бұрын

thank you what about a torque wrench for the idler and tensioner I don't have one.

@Juan787ful 7 жыл бұрын

hey buddy Im trying to put my 03 focus on timing and I got few quentions.

@spanktank6582 7 жыл бұрын

Juan787ful what's up

@Juan787ful 7 жыл бұрын

Chester Hancock Jr. when you put the plack behind the cam shafts, do you put the gears on timing with the plack on?

@Juan787ful 7 жыл бұрын

im having a hard time tu put on time, 03 ford focus zetec is off time and and have no timing marks on

@spanktank6582 7 жыл бұрын

Juan787ful you got to get a timing tool

@spanktank6582 6 жыл бұрын

Juan787ful yes u do

@JC-oz6xn 3 жыл бұрын

Wish you lived close by, I'd run my zx3 in there and have you re belt it!

@atlred 4 жыл бұрын

Where are you from bro, I lived in Ga. 23 yrs...if you want to get to the store, go down the street turn left after you turn left you going to see a big tree with no leaves on it, look to your right in the store be right there.

@lightningvolt1273 4 жыл бұрын

How much would a job like this cost at a local mechanic shop??

@spanktank6582 4 жыл бұрын

Probably around 800 to 1000 bucks or more

@hillyardwp 6 жыл бұрын

Do u need the special tool to do the timing belt can I get her done without it?

@spanktank6582 6 жыл бұрын

hillyardwp u can but i rather have the tool you can go to your local autozone or orelly to rent the tool its a ford timing tool after you finish with the tool you take it back and they will give u your money back

@anthonyarmstrong9939 7 жыл бұрын

Wiy don't u Loren to top sprockets bolts to get even tenchone on the help pal .is it a short cut please email bk doing won in the next week.

@mybestieischloer2401 2 жыл бұрын

dude, learn how to spell.

@johnnyfivealiveable 4 ай бұрын

Why won't the front cam stay in alignment

@spanktank6582 4 ай бұрын

I got to have the cam tool

@johnnyfivealiveable 4 ай бұрын

@@spanktank6582 I have everything aligned but when I take the alignment tool out the front cam shaft rolls back not straight anymore am I off a tooth or something

@spanktank6582 4 ай бұрын

Yep