There is a special place in heaven reserved for you for the tape trick. The map lights are BY FAR the trickiest of all the lights.

Dude!! I have been dealing for 2 days with the mapping light.!! You save my life with the tape recomendation!!! Thanks a lot!!!

Thank you for the tape tip!! I've been trying to take them off for about an hour now. Thank you, thank you, thank you, thank you!

Hands down, the best video on KZfaq for this!! Too bad I found it AFTER I watched a dozen others and did my install. Everyone else was in a hurry or wasn’t thorough enough. Thank you.

Great video! Lot's of detail on the removal & replacement of the lamp housings and covers. This made my LED conversion project quick and painless. Thank you!

Thank you for this much needed video; especially the puddle lights

Thanks guys! Made it super easy installing my new LED bulbs and I didn't break anything!

Clear and precise. Need more tutorials like this.

Excellent video, it was greatly appreciated

Awesome video and description! You guys make it look easy. I only had trouble removing my passenger trunk light. In the end all bulbs replaced with LED’s! Ordering headlights and dogs! Thanks for posting these videos! 2019 4Runner!

I know this video is old, but helped me a great deal today. Thankyou. ( using tape was genius, I tried everything). Cheers

this is a great video, i bought LEDs off amazon and then found your video for instructions. wish i would have bought my bulbs off you just for the free tools. thanks for the info.

That mapping light was a brilliant solution and I had to comment to say thank you. This was an incredible video.

Great video. Using the tape for maps lights alone saved me time and aggravation

I just got the full Precision LED kit installed on my 2016 4R, and I have to say I couldn't have done it without your terrific install video Phil. Just a world of difference with the increased lighting output as I live in a snow state. Terrific work! Just a couple of notes I'd like to mention from the install: 1) I had trouble removing the courtesy light fixture from the light housing (the part where you have to push on the tab). I found out that it was much easier to slide the plastic housing forward instead of simply trying to pry it apart with the pointed trim tool, and that came apart much easier than simply trying to pry them apart. And they slide back in easily with the lovely "click" sound. 2) One of the trunk light LEDs (as there are two on the 4R) is not as bright as the other. I will have to see if it was an error on my part on the installation or maybe one of the LED bulbs got damaged during the shipping. Either way, the lights are much brighter now when I'm loading the trunk with groceries after work in the evenings. Just can't rave enough about your product! 3) The plastic trim removal tools are AMAZING. I cannot give you guys enough props on that. I may have to purchase another set as the pointed tool got damaged quite a bit during the install, and I would like to have a backup one for future interior modifications. Just amazing and terrific tools from PrecisionLED! Thank you again!

great work, been wanting to upgrade my interior lights. This certainly makes it much easier to complete, thanks for making the video!

by far the most informative video on youtube about this subject, great job and please continue making videos like this.

Guys, GREAT video. Thank you for putting this together. Just ordered a kit from your website.

Smart presentation! Best explanations on KZfaq so far

thank you for the detail instructions !!!

Thanks a lot for making this video!

Love your attention to detail. Thank you!

THANK YOU!!! made my life alot easier great video quality and content thanks again

Excellent Video!!!.I juts picked up a Trail Premium last week and will be doing this ASAP.

Just finished installing your premium kit in my 2015 4Runner. The LED's were a great upgrade. Most notably, the puddle lights are actually usable now! Thanks for the excellent tutorial!

Excellent tutorial video! Keep it up sir!

This video was a BIG help!!!

That map light was a b. Thanks for the tape trick. Definitely help LOL

well done... been looking at 4runners and if I do get it this is a must do/buy :) thanks for the video!

Legit easy to understand video. My only suggestion is when re-installing the mirror, leave the top part off and use the hole in the housing to connect the mirror heater first then snap the mirror in and install the top part. This removes the squeezing your fingers in behind the mirror. Thanks for the awesome product and video!

thanks for the great video - helped out a ton

Excellent, thanks for the video.

PERFECT VIDEO MY FRIEND YOU SAVE ME A LOT OF MONEY... THANK YOU......🇲🇽

The upper center console around the map lights is designed to be pulled down to replace the bulbs from the top. The come out and go back in with a quick quarter turn. Mr. Toyota designed it this way.

Thank you for the great demo! I'd only add 2 things: a) Use packing tape for the map lights and roll the tape into a tube to make removal easier. b) The door lights have little arrows that point to where to insert the tool. If you can spot them, it takes the guesswork out of the tool placement.

Orders my kit looks great inside and out

Awesome video. Great job!!

Used a small strip of gorilla tape on the maps. Slick!👍🏻

I would love a video for the actual hard stuff! Front Signal Light and Fog Lights. Otherwise I agree, one of the best videos with good camera work and detailed explanation!

thanx a lot the video was really helpful. and the bulbs gave the car amazing look :) also when i was buying leds i made a mistake and ordered 2 instead of 1 but they wrote me and asked me if i wanted 2 and returned me money :) thanx a lot once again ;)

Love the lights and very helpful video on the installation of each light. I will say I don't know what kind of black magic voodoo tape you people have for removing the map lights but I had no success in just pulling those out in my 2017 4runner. I ended up removing the overhead console and switched out the lights that way, and only took about 5 minutes. They all look great!

Thanks it was a nice video I'm sure it'll help

Killer job bro 👍 subbed

Great video !

Perfect description of details, thank you. Do you mind explaining how to change the glovebox lightbulb?

Great instructional video guys. A couple of points to maybe make it easier for the next guy. The clips to remove the mirror caps are the same color as the cap itself. So if you have a black cap it may be harder to see. Also, when you remove the piece around the mirror housing you don't have to remove the built in indicator signal. Last point: when doing the map lights, if you have big fat fingers like mine, be patient! The tape is a good idea. I ended up using duct tape to get mine out...

2:30 tape to the halogen bulb, GENIUS IDEA!!!! I couldn't figure out how to get that bulb out without damaging anything.

Awesome video!

Excellent video

The tape around the bulbs was genius, thank you! Have you swapped the glove box bulb?

When doing the puddle lights, I found it was easier to reconnect the mirror heater if you leave the back color keyed trim off until after mirror install. There’s a convenient space to then plug the heater cable into place. All you have to do then is snap the color keyed trim piece back on. Finished.

This is a great video and product. Just finished installation and I have two comments; 1) I used pieces of heat shrink over my needle nose pliers to remove map lights. Much easier that tape, 2) the courtesy door light assembly removal instruction is a bit unclear. Where the clip disengages depends upon driver side or passenger side thus be very careful not to force its removal. I used a bit too much and broke the lense clip. Otherwise super cool. Can' t wait until dark to see the difference.

This video was very helpful, especially with the mirror puddle lamps. Even with this video, they were still horrible to change. One of the clips broke when removing the mirror.

If anyone is looking for how to replace the puddle lights like I was on a 2013 4runner, its about a 2 minute job vs the 2014+. Just remove the mirror glass like they show you in this vid and unscrew 2 Phillips screws right below the white disc that the mirror snaps onto... once the screws are out the lens can be pulled downward, then just twist the balast from the lens. replace bulb and put back together. your welcome.

Tape doesn’t work on my 2015. So frustrating. Finally got tape to work on map lights. Thanks

Best video I seen, have a question but not sure if your model compared to a 2016 ltd is the same. Driver and passenger light under dash that is very dim but lights up where you feet go under the dash area, How do get access to it and type of bulb? Thanks

Very thorough tutorial! Do all the bulbs dim as they turn off like stock? In particular the puddle and interior dome lights. Also do the brighter back up lights interfere or wash out the backup cam?

Thanks for this video. It was very helpful. I’m just not that confident in myself on changing the bulbs in the mirrors.🤣 I’d rather pay a professional to do that part. My luck, I would drop the mirrors and break the exteriors.

Are these 6000k or 6500k? Awesome video as usual thank you!

Wish I had seen the tape trick for the map light before I crushed them with a pair of needle nose pliers trying to get them out!

please do the head,tails,and DRLs for the 2013 and below please?

Thank you for the great tutorial, so helpful for the un-informed. One question please? Are the led's on the dome and rear interior tail/dome lights the same bulb as all the rest? If not, and I suspect that is the case, what is the bulb name and number as I'll need to order them? Do they come in different watts/lumens and what is the recomended brightest light compatible with a 2016 4 Runner? Thanks so much.

Can the small light between the map lights be changed? I believe it's just a mood light that casts a little lighting on the center console and center stack.

Very good!!! Do you have a video on a Nissan Xterra 2012 Pro4x ?

👍👍👍

after installing the led bulbs for the reverse lights, did u notice a drastic better visual illumination feed from the back up camera?

Which LED's did you use, crystal white or cool white? It would be nice to see a video that compares the two colors.

What about the glove box light

How about LED DRL ,Breaklights, Turn signal and Headlights for 2013 4Runner?

Could you please do a video on how to replace the glove box on a 2014 Toyota 4runner?

This kit link is no longer valid. The existing 4runner kit for 2009+ has the trunk lights listed as optional but no item selection. What is the product ID for the trunk lights? Same bulb as the dome but the only way they are identified in the Toyota manual is "8 watt double end".

what color are these in the install?

I think the guy in the video did a great job of explaining and has a real talent for making videos. However, I do agree with Chase K that it would be better without the music and allow us to concentrate more on what he is saying. Question: how many MM long is the Dome light bulb for a 2011 4Runner ?

Does someone make an entire kit for a 2016 trd pro 4Runner for all these lights ? Getting my headlights installed tomoro and want a full upgrade . Thanks

The 2013 4runner puddle lights was easier to replace, I only removed the mirror and couple screws.

You don’t have to remove the mirrors.. you just squeeze the corner inside piece in the front and pull it to the front! Waaaaay easier than removing the mirror

How do I do the glove box light?

Gotta ask since its not covered......what is the light in btween the map lights and how does that get changed? Thank you.

Do you have a video in the 2011 4R limited or it is the same?

I'd assume that this would work with a 2018 TRD Off Road? Am looking to purchase your premium package. Thanks!

Quick question for anyone who has done this install, how much brighter are the new bulbs than the halogen ones? LED's would be nice but these almost seem blindingly bright. Any feedback would be great!

For the 2011 4runner you don't have to take off all that plastic for the side mirrors. All you have to do is remove the glass and unscrew two screws that hold the light. The light simply pops out. Here is a link to some pictures. www.toyota-4runner.org/5th-gen-t4rs/62252-interior-lighting-mod-4.html

Hi would this package fit my 2021 Toyota 4Runner?thank you

Hi so when I started to install the led dome lights I was having and issue with it.. The light was working and couldn't lock it in.. Now none of the lights work after just running .. I'm looking for a fuse blown but not having any luck with a good description of which fuse it would be..

about the glove box?

What's the difference between the premium and non-premium package, aside from the price?

Trying to find the puddle light on the website but I can't find the led? Is it part of the interior base package?

Please show a Ford Cmax or let me know what video to watch. Do you offer an HID kit for the Cmax headlights?

Hi I had a 2019 Toyota Tundra and I had LED in the truck would they fit this new Toyota 4Runner 2021?

2020+ 4runners use 28/29mm length for the dome NOT A 31mm.

2015 models work the same?

Anyone find the dome light doesnt sit properly ? I can fit it in and it'll turn on but the bulb itself doesnt look straight. It fits in a bit of a slant

Are you using the 6000k or 8000k lights in the video?

Hi is there anyway you can a shortage?

Any one how to switch out the glove box light?

Is this 6k or 8k conversion?

How do I change the glove box light?

How about glove box light?

Was this 6000K or 8000K????

Would be great if you showed the finished project at night.