Thanks for the great video! Following your example, I just took mine apart, gave it a nice clean and polish, put it back together, and it is running!!!!

Nice work. It's good to see a man that is skilled with intricate details like a diesel injection pump. I'm sure that you will always have plenty of work to keep you busy, and keep the $$$ rolling in.

Is there a vidio showing how you removed this..

Hat mir geholfen meine Pumpe wieder richtig zusammen zu bauen. Vielen Dank.😀

UH O,,, unscrewed the wrong one!!! Lol!!! Just kidding,,, thanks for the tear down vid,,, it’s people like y’all that take the time to make these videos help out a lot of do it yourselfers,

Thanks malaking tulong yan boss .natapos ko yung ganyang project ko kanina

Very thoughtful and very useful and very clear

Great video. This is going to help me tremendously. Thank you!

Grazie x questo video, molto bravo complimenti, ciao

Hello friend, I have been watching your channel for some time and I can learn a lot from it. I have a Kubota B1400 tractor with a D850 engine and I have a question about how to set it up idle speed in this engine? The engine runs very slowly, and the revolutions fluctuate. When the engine is running, after opening the inspection cover in the pump casing, you can see that the spring and the rod that move the toothed rack, which is in the form of a cylinder, moves to the rhythm of the waving revolutions. When I move the rack with my finger and increase the revolutions, the engine works normally. when I let go, the revs drop and the engine cuts out. What is the cause of rpm fluctuating? the rack link should probably be stationary while the engine is running? On the opposite side of the pump's gear rack, there is a small cover screwed on with two screws, underneath which there are concealed locking pistons. There are three pivots, the central one which is stationary and two side ones which are mounted on the eccentric, can they be adjusted? what are these two side eccentric pins for? Do they regulate idle speed? I will be grateful for your response.

Did you have the tractor on TDC Since you TDC the injection pump. I heard it a pain. I have the same problem with my B7610. I have done my 4020 JD with roller master injector pump.

Thanks for showing how these are assembled!! I took mine apart and cleaned it but wasn’t sure how to time the gears. I’m still not 100% sure how to align the plungers ? Looks like they need to be aligned properly, what am I looking for to properly align ?

Un GRAND Merci , thank you very much indeed , Muchas Gracias

What an awesome video, amazing footage , keep it up brother

Thank you. Thank you. Thank you!

What is in the pan that you keep dipping the parts in before you reinstall them??? Is it parts cleaner or diesel? Thanks. Very good video.

Hola , tengo un tractor con ese tipo de bomba, tira mucho humo a los 10 minutos de esta en marcha y olor a gasoil , creo que hay que adelantar un poco la bomba , podrias comentarme como se adelanta este tipo de bombas ? Gracias .

I found the video! I’ll watch it today and follow your steps!! Thank you so much for taking the time to show your rebuilds and repairs!! Where are you from?

Great video. Is a Westerbeke pump the same as the Kubota you showed us? I think my plungers are gummy after sitting for over 6 years. I think I'll let an expert rebuild my Westerbeke pump. Just in case.

❤❤❤I love your videos

You're the best👍

What is the model/part number for this pump so that I can source spare parts - excellent video - worked for me.

Very nice work. Im having trouble getting the injection pump out . The shaft in the middle is stuck in the fullest out position and making it impossible to pull the injection pump upwards. Any ideas how to solve this?

Nice video thank yo so much, I have a question for you I found shims that goes under the rocker and have the inscription 375-370- and 365, do you thing where they goes respectively, I think 375 goes for piston 1, 370 goes for piston 3 and 365 for piston 2, regarding firing order on my tractor, the 375 is thicker than 370 its self thicker than 365, I think the thickness gives 1.2 degree between each injection time. thank you so much .best regard from Canada

Hi @tractors&marine MECHANIC, i have a Mitsubishi L3E engiene and the Fuel Injection Pump 094500 is very simular to this on your video ? I need the O- rings for the 3 fuel nossel i have one leaking after dismantle , do you know were i can get that ?

I’m trying to rebuild the same pump but am in need of some control sleeves. Mine are stripped. Do you sell spare parts or where would you go to get control sleeves?

gute Arbeit, vielen Dank

Very very good thank you

Hello. Would this cause excessive smoking?

These videos are very helpful, thank you. I am about to rebuild a yanmar injection pump (John Deere part AM101403). What is the cleaning solution that you use?

احسنت بارك الله فيك

Good job !

Hi, thanks for detailed video. I had the rack stuck a fews years ago and had to do that. The gen was a few years working with no major issues until now that get high rev all the times and I had not find the way to restore normal RPMs for work. When I started it go to full acceleration and I had to cut the fuel for turn off. Could be the rack governor loose in any way and stuck in high RPM? Any advice? Thanks. Is a Cummins onan 7500 with kubota 3 cylinder engine

Impressive boss

I tried to disassemble and clean my pump quite similar to yours. When I test it without the lines connected (only diesel in-line), it only delivers diesel in two of three lines. What can be wrong?

many Thanks for sharing

I have a 2cyl pump Can't get one of the assemblies to align and place the screw to lock in place, if I do, I can't open and close it jams...and the spring and roller stay jammed seems like everything is align and proper position any idea what I'm doing wrong?

Hello sir. Same lng po ba ng injection pump sa lahat na na bangit sa engine ? From 1802 to 2601? Same lng injection pump nila sukat?

What are the two bolts on the back? The ones under the data plate.

Pump testing tool hi kya

what are you using a solvent / cleaner?

Where can new springs be purchased?

Great video, but terrible background music or sounds !!

What are those parts inside pump called??i wana do a rebuild on mine.does it have to have 12v to work?

Wow

parehas ba cla ng plunger ng 3d84-1fa boss?

Hello sir. Nag leleaking po injection pump ko. Tuma tagas ang grudo pumupumta sa engine oil ko. Ano po kaya problema ng injection pump ko sir . salamat sa sagot sir

leopard same 85 exp

Ano possible na sira sa PTO bumabalik kc Yong second gear sa nuetral

Hi, I need help fixing a Yanmar engine. Please help me. Do you have a phone number?