Terrible camera, gang. So sorry. Just fwd 3:20 to 4:57. Not sure how I missed removing this useless footage before I uploaded.
Пікірлер: 27
@SaleenDriva3 жыл бұрын
Thanks for the helpful video, I couldnt figure out how to get the key shank out!
@CaptainSeamus2 жыл бұрын
Thanks for this video. Just got mine fixed and works great again!
@blutospartan76522 ай бұрын
Heat the side you're cutting with a heat gun or hair dryer, the glue will let go. Just clean off the excess glue and it will reassemble like new.
@Bigtime_mcalpine2 ай бұрын
F m…wish I would have thought of that. Thanks.
@inogomez60 Жыл бұрын
The one thing, and the most important one, is where to get the replacement part???
@frederikboersma2 жыл бұрын
since you are going to use a brand new replacement fob housing, you dont need to spare the FOB - the only thing is to spare the glass transponder. Once you know which side that is on (the keyblade side) you just open the other side with a screwdriver and appropriate force, the fob will burst open in halves and the transpodner nicely exposed so you can take it out, including the keyblade. No sawing needed!
@CaptainSeamus2 жыл бұрын
Not always... I did mine just now - and the glass capsule was glued in from the factory (original 2004 key). So I had to do a bunch of very delicate scrape and cut work to get it out.
@andybauer96895 жыл бұрын
dermal drill with a skinny cutting disk works the best
@Bigtime_mcalpine5 жыл бұрын
andy bauer hmmm I’m not sure about that. You might end up cutting too deep and too fast.
@CaptainSeamus2 жыл бұрын
That's how I got into mine - as OP mentions though, be very careful not to cut too deep. Also, I noticed how the glass reinforced plastic on the fob tends to melt and harden on the disk as it's cutting - so be aware that you might end up cutting a little and then not at all until you remove it (or break the discs like I did)
@florinnecula3650 Жыл бұрын
Bravo
@seannewman17613 жыл бұрын
So... I crushed mine too get the key out. Fob didn't work anyway. Now car won't start. Please help.. same fob
@Bigtime_mcalpine3 жыл бұрын
What exactly did you crush? Hopefully not the little transponder...
@Bigtime_mcalpine3 жыл бұрын
Assuming transponder is good just hold it hear the ignition cylinder while you use the key turn turn engine over.
@seannewman17613 жыл бұрын
Yeah I feel pretty dumb now, but I learned something not to do in the future. I taped the transponder right next to the ignition, bingo👍 thank you
@1gbsebslp4245 жыл бұрын
How did you fix it?
@Bigtime_mcalpine5 жыл бұрын
kzfaq.info/get/bejne/kLanZs9htd_epI0.html
@renatograziteamo97232 жыл бұрын
Boa tarde amigo .como programa esse controle no carro?
@Bigtime_mcalpine2 жыл бұрын
No programming is possible. Only dealership can do that. You must have a chip that is already recognized by your car. Hope this helps.
@renatograziteamo97232 жыл бұрын
@@Bigtime_mcalpine a chave tá funcionando ..eu comprei o controle novo de abrir e fechar o carro...preciso programar apenas o controle
@donow84647 ай бұрын
lol, or live with a floppy key
@ahhgea3 жыл бұрын
Could do without the 3 minutes of nothing.
@Bigtime_mcalpine3 жыл бұрын
Yeah wish I kept the original footage so I could fix...
@TheBeemerfan4 жыл бұрын
fell asleep?
@Bigtime_mcalpine4 жыл бұрын
Mario Lemoine haha, yeah I only noticed that bit a few months after posting and I’ve since lost the footage. May have to see if I can download and edit. In the meantime I certainly won’t be quoting my day job.