Thanks for video - explains a lot

thank you very much for the video you are a pro please you can explain to us how to make a basic setting with vcds thank you very much

Thank you very much for your video - help. Very important

Thank You !

Thanks bro 👍👍👍

After positioning the flaps manually, did you do the basic settings in VCDS with the servomotor mounted in position or out of the working position?

Thank you

how did you remove the plastic bracket that holds the v113 motor?

@golfWagen mine makes the sound @8:20. Is it bad?

What are the symptoms of bad v71 motor? My heating will only blow into cabin if i press recirculation button🤔 no air blows when when recirculation is off but I can hear the motor for fan running

My Golf 5 2005 has two actuators here. Common problem. I had to changer 2 DC motors(Bosch) and 1 potentiometer (AliExpress) on all flap actuators in car. And three DC motors in door lock part...

HELLO I HAVE GOL7 MANUAL CLIMA AND ON RIGHT SIDE EXIT ONLY COLD AIR WHEN I SWITCH HIGH TEMPERATURE ,ON LEFT IS OK . COULD BE THE SAME PROBLEM ?

I have new fan on full I hear it but no air coming from vents any help ?

Thanks for helpful video ,when I scan my car seat ibiza 6j I have two errors the first 01087 error code base sitting and the scand 01272 ServoMotor central flap V70 ,when I checked it i think the same problem as in the video ,help me please

Prosím ťa, na Superb 3 mam ten istý problém, musím vymeniť motorček, lebo ten potenciometer ktorý je tam neviem zohnať. Inak motorček sa točí tam a späť, ale iba keď nieje zapojené do funkcie. Keď to namontujem a urobím kalibráciu normálne ide a ide aj vymazať chybu s diagnostikou, ale po chvíly už zase nefunguje a zostanu klapka otvorená.

Thanks for the helpful video. I tried replacing the V71 motor on my 2008 Skoda Octavia MK2 Estate, which has the exact same motor assembly and climate control unit as the golf pictured here. I thought the motor was broken because in normal operation the motor pulls both flaps open, then closes them and then it pulls the little white wheel completely to the other end, which opens both flaps again. In other words, the motor always goes through it’s full range of motion, so as a result the car is always in recirculation mode, regardless of the setting on the climatronic. I checked the measuring block in VCDS and it does give a reading of the flap position, but the actual position of the flap is way off. Do you have any clue what the problem might be?

i get 01272 "positioning motor for central flap (v70)" error, would you give tips on how to reach it and have it replaced on a 09 jetta? Thanks in advance!

I find no security access for air conditioner module vcds it's good 20103 to do basic setting thank you very much

Hello, is it center drill air motor v71? There are not cold and warm air center drill but sides is ok. Can i change it v71? Thank you

What ist this Sound ? 23:02 „tak tak tak tak“

I kindly ask your support! I changed the motor with new original one. But the error V71 remaining, even after basic setting and cleaning fault codes. The motor is doing only partial movement. without motor everything is fine and mouves properly. Before to quit and go to the dealer, do you have any idea? Thank you so much!

Ciao ...come si fa a smontare l attuatore che comanda il parabrezza? grazie

There are no problem solving steps.

the v425!!!

The whole disassembly looks hard

Was the electric motor broken?

Is it 4.7kOhm resistor?

Really out of any help! Comments are in 3 or 4 different languages, I guess that gent have no ideea about how to measure a feed-back potentiometer. Remove from place, connect ohmmeter to any 2 terminals and turn slowly the middle moving part. One measure should read constant, other 2 measurements constant increase and decrease of resistance. Any drop of value means a damage of resistance portion of potentiometer. Without solid knowledge of electronics to repair, means you will need a new one.