ZIPPED!!! Husqvarna 395XtraPower ANNIHILATING A Stock 395xp

Рет қаралды 15,260

3 жыл бұрын

Filmed in March 2021.
This was a standing dead Ponderosa Pine. Growing around 4000'. Somewhat wind blown, not to far off the prairie edge. Some will understand what this means.
As eluded to, a redo on the modded saw. Slight glitch on the owner's part. Gave me an opportunity to try a little tweak I thought of while looking at the innards of another saw on the operating table awhile back. Appears to be helpful.
The "ZIPPED" saw is the Psy-Ko S version zippkit (5½ on the list of 6 levels) with my "patented" "Torque Tweak" added into the mix. The modded 395 is heard running slobbering rich. Nowhere even close to being "carb-a-tooted" correctly tuning wise. Seen here laying waste to the stock version.
Looking at the timed runs -
Bone Stock 395 tuned to 12,480 went 22.60 down and 23.10 up
Psy-Ko S 395XP tuned to 12,600 went 17.30 down and 17.88 up
Again, pulling HARD on the zipped 395 coming up as seen coming out of the cut. No real audible difference in the engine sound as compared to going down.
I'm well pleased at how the Psy-Ko S zippkitted 395 turned out. With any luck, so will the owner.
I'm currently available for custom saw modifications. If you are interested, please shoot me an email.
danger_cat@rocketmail.com
Thanks for watching
Hello. Timed runs, albeit embarrassing for the stock 395, are posted in the description. Along with some additional information, as usual. Pursing the description might answer a question or two beforehand.
Thanks for watching.

Пікірлер: 45

@hotsaws101 3 жыл бұрын

Hello. Timed runs, albeit embarrassing for the stock 395, are posted in the description. Along with some additional information, as usual. Pursing the description might answer a question or two beforehand. Thanks for watching.

@isaaclay5510 2 жыл бұрын

How can I get ahold of you to send you my saw

@kraftzion 3 жыл бұрын

I've watched a LOT of saw videos on you tube, yours are far and away the best. Stock vs ported seems like a no brainer to me if you port saws yet you are the only one who does it. Really like your disassembled comparisons too. No real wood to cut here in Florida, still like chainsaws. Bought a German made 7900 many years ago, had to sell it after couple of years,needed the money. Just bought a blue copy of my second favorite saw last week(372xp).

@dcvariousvids8082 3 жыл бұрын

That Zipped saw really flies in the cut! Can’t see the owner being disappointed.

@lumberjack24.a.theoldschoo24 3 жыл бұрын

Yeah there's nothing better than a dang 395 special on Jack builds it yeah keep up the good work you're building dang good saws

@dinkoterzic Жыл бұрын

394 395 💪💪💪💪

@ironcross13 3 жыл бұрын

Same wether in Nehalem Oregon.🤘🙏

@Robbie..Ha-Navi 3 жыл бұрын

all i run are 395s . saws are total badass

@bulletholesbobby Жыл бұрын

Awesome!

@PuskwaskaOutdoors 3 жыл бұрын

That’ll be a lot of fun turned up another 1-1.5k...

@scottalan4034 3 жыл бұрын

Jack, in your humble opinion who would come out in top? Your torque monster 481 or this zipped 395? Would be an interesting comparison considering the 461 gives up almost 20 cc's

@dinkoterzic Жыл бұрын

395 💪💪💪

@hotsaws101 Жыл бұрын

The zipped 395 would win. My 461 would not be to embarrassed though. Thanks for watching.

@benredmond8271 2 жыл бұрын

What is your opinion on the 395 made in Switzerland over Brazil?

@jimjackson5836 3 жыл бұрын

Jack you must be speaking of the new 592 and the tach situation? Hope it's as good as they say.

@hotsaws101 3 жыл бұрын

Jim hi. There are two "big kid" saws in the wind as far as I know. 585 & 592. The 390 replacement has been spoken of for at least 7yrs that I know of. The 395 "upgrade" is about the same. Either, neither, both, will, might, possibly be available at a dealer near you this fall. That may, or may not, be all I know. Thanks for watching. .

@treystewart544 2 жыл бұрын

@@hotsaws101 those saws are awesome

@chocryder 2 жыл бұрын

Hey nice working saw. I got a 395 and I can’t get to rev 12500. I can turn the screw all the way in and won’t get there. Any idea what might be wrong?how many turns out should get the right rpm?

@hotsaws101 2 жыл бұрын

chocryder hi. In stock form they have limiter caps preventing more than a turn of rotation on both the high & low speed needles. I think that the factory states optimum rpm for that saw in stock form is 12.5. In stock form it sounds like they are going to explode much above that rpm threshold to me anyway. I would put more emphasis on the screen color. Dark brown and it's about right. Probably won't blow it up from a to lean condition either. Best of luck & thanks for watching.

@chocryder 2 жыл бұрын

@@hotsaws101 I have the limiters cut off it.

@hotsaws101 2 жыл бұрын

Then there is some sort issue... Could be a charge flow issue, whether it be air or fuel, or both. That could a restriction on the exhaust side as well It could also be an ignition coil snafu. I've seen where they are bad when new. I'd also check the air gap. It's is about impossible to tell what's wrong "over the phone". You might have to bust into the piggy bank and hit a reputable shop fir a little diagnostic session, lol.

@chocryder 2 жыл бұрын

@@hotsaws101 I had a a new hyway top end on it and thought it might be the problem. I since taken that off and put a oem cylinder with the hyway piston. Do you think it could ever be the carb? I did a carb kit to Thanks

@TonaldDrump686 2 жыл бұрын

@@chocryder hyway commonly have more quench distance than oem, this will give lower compression and less than oem performance. .005 brass sheet makes a suitable base gasket rather than removing it all together. Maybe measure it (squish) and and have the appropriate amount machined off the bottom of the cylinder. A guy shouldn’t have to put that kind of effort to regain stock performance but, it is what it is.

@VinnyMartello Жыл бұрын

I have a true Husqvarna 395 with dual port muffler. Really wanna port the jug.

@batmantiss 3 жыл бұрын

I'd pay ya!

@brianandrade1689 2 жыл бұрын

You run square grind or round file?

@hotsaws101 2 жыл бұрын

Brian hi. Square grind and/or file. Thanks for watching.

@uncletony3674 3 жыл бұрын

Where can I get that compression tool?

@hotsaws101 3 жыл бұрын

Uncle Tony hi. Is it the tachometer you reference? The saw shop is where I get mine. Thanks for watching.

@prescribedfire1953 3 жыл бұрын

Jack what elevation are you at?

@hotsaws101 Жыл бұрын

This was 2800 or so. Thanks for watching.

@mr.fridggyyy5826 3 жыл бұрын

If you build saws for people, or have time to rather i would like to get in contact with you. Thanks for the video.

@stephanmackie5281 3 жыл бұрын

Mr Beelar is a badass. Super nice I’ve talked to him on the phone for 40 mins on the phone one night. He definitely knows his shit. He’s got much respect from me.

@stephanmackie5281 3 жыл бұрын

If he doesn’t respond send him an email

@mr.fridggyyy5826 3 жыл бұрын

@@stephanmackie5281 I watch alot of his videos and I am thoroughly impressed. Granted, I dont understand all of it but it sure sounds good LOL. What is his email adress?

@BenOfficial94 3 жыл бұрын

@@mr.fridggyyy5826 danger_cat@rocketmail.com

@stephanmackie5281 3 жыл бұрын

@@mr.fridggyyy5826 look under his description. It’s dangercat something something. Under description of the video. He’s got a lot written there. Bottom bit has his email

@maninaboysbody 3 жыл бұрын

I think the "394 sleeper-aka ugly betty "just got spanked!! lol. I ain't tellin her. maybe with this stimulus check I could get my 288xp "Torque Tweak"ed? Ill let u know thanx again.

@hotsaws101 3 жыл бұрын

Roy hi. Yah, no. LOL. Ugly Betty would be not winning here. What we see here in the zipped 395 is not run of the mill type work. Win the Lottery,,, then CALL me! We will get you fixed up, hahaha! Thanks for watching.