It pays to be patient with those chips! Lol after a couple times redrawing to clear chips it starts to get annoying real quickly lol Obviously bad idea to act like they don't exist 😂
@douglasskinner21 күн бұрын
Best demonstration of Jacot tool I've seen on KZfaq. Thanks for the advice about the tapering problem and stepping down the grooves as a way to minimize it. This is not mentioned in most demonstrations. I don't seem to be able to find qbstuff. Are they still in business?
@gendernicАй бұрын
This is a really helpful series, thanks for doing this!
@GilbertoAmezquitaАй бұрын
Good video. I cannot find part 2.
@home-dp6oh2 ай бұрын
I feel your pain brother. 2 things I hate the most: fitting roller jewels and hairspring work.....
@user-rq9po2zv4k2 ай бұрын
Дуже важливо знати 😊❤
@douglasrivera38923 ай бұрын
I would like to fix my rolex 1500 it seems to have problems I am from Puerto Rico if I have to send the watch let me know thank you
@timmy11toes3 ай бұрын
Thank you so much for such a clear in depth tutorial into the Jacot tool and burnishers. Iv just purchased a clean full set and awaiting their arrival. Your content will help me no end and you now have a new subscriber.
@wmbchristie3 ай бұрын
I love the (higher grade Waltham) American grade and Amn grades! Your desire to restore this, as you said “basket case” movement impresses me considerably. I will be following your progress with interest!
@jeffreyyoung41043 ай бұрын
When I first I saw the device, I thought it was a thumb lock! But then the real explanation made it clear!
@dcsmit314 ай бұрын
I just wanted to thank you for all of your watch repair videos. I have learned much from watching them and it has helped me advance my watch repair skills. Your in-depth explanations are a valuable asset to all learning this amazing craft. Thanks again.
@zachary42254 ай бұрын
I just started collecting pocket watches. I got a really nice one I need to get going
@robertbrandywine5 ай бұрын
I'm confused. I thought the purpose of those screws was to adjust the balance of the wheel. Why would you need to lighten one?
@georgepanagopoulos14156 ай бұрын
I love the chain with the leather connection. I’m assuming you bought that new for this watch. Where is it from? would love to have one for my Illinois pocket watch
@radoslawjocz29766 ай бұрын
Burnisher is rolling the surface not filing. It will reduce the diameter of the spigot but not removing material or removing it very little.
@horstb297 ай бұрын
Congratulations good job
@horstb297 ай бұрын
Thank you for taking the time and effort to show us the pivot reconditioning procedure.
@quaarjet7 ай бұрын
You can take some metal polish and polish the new and old jewels in the plate and you won't even able to see the difference
@avianfish87328 ай бұрын
Hi, how much total weight did you remove?
@Donnybrook108 ай бұрын
I had the same problem with a Waltham 220. The star was completely rusted and the screw on teh bottom was also rusted. I successfully freed it up with wd40 and it all cleaned up nicely. Replaced the star, blued washer and screw.
@Donnybrook108 ай бұрын
well done...those tools are insanely expensive but we need them.
@wildernessofzinn178 ай бұрын
Wow...thanks for this video. Thank you so very much. These is the kind of stuff I'm talking about!. Good man! You are only one of a couple who even bother showing these important matters. All most want to do is just video themselves cleaning, oiling, slapping it on the Timegrapher and all is perfect. That almost never happens. For instance, understanding what the Timegrapher is telling us is what I need. The prognosis/diagnosis thing. e.g. I had a watch I cleaned, oiled, and it seemed to run well. I put it on the Timegrapher, and it showed a huge amplitude drop from horizontal v vertical position. Why?. What is that a sign of?. See...that is what myself and many other newbs out there need to know to learn to be good watchmakers. Thank you so every much for these detailed videos on dynamic poising. This is what I have been wanting to learn and practice but there is little info out there for us rookies. Thanks. Thanks. Thanks
@johnhannon9 ай бұрын
Thanks for the video on the Jacot tool! Unfortunately, those pivot gauges are going for almost the same price as the jacot tool! Yikes... Would it be possible to just buy a set of jewels of different sizes and make one?
@andriych26009 ай бұрын
Super! Nice!
@MrVinman9 ай бұрын
As always you are very informative...great video.
@MrVinman9 ай бұрын
Great video...I appreciate it.
@MrVinman9 ай бұрын
Awesome job on this video...thanks.
@victorlozano77389 ай бұрын
Question: What kind of alcohol are you using on that video?
@paulkuziel786911 ай бұрын
Do you take watches in for repair from the general public?
@runelisether6256 Жыл бұрын
Thank you! Very clear and informative.
@danielowens4789 Жыл бұрын
I have an old CYMA PW with the exact same style of settings and jewel broken 3rd wheel bottom plate, I purchased another movement with good jewels. My question, is it possible to push out the setting and jewel complete from one movement and install into the other, assuming piviot hole size is correct? Thanks!
@quaarjet7 ай бұрын
Yes
@danielowens4789 Жыл бұрын
It’s nice having the correct tools for the job. Good job!
@sylversyrfer6894 Жыл бұрын
Excellent narration! Really appreciate your detailed commentary (e.g. lifting the hands straight up from ceramic dials - never heard this before but it makes sense). Also, explaining certain terms (e.g. end shake and side shake - hear it a lot but no clue what it meant)!! So THANK YOU!!
@roadshowautosports Жыл бұрын
Good video! Wish you had shown the under cutting process in more detail as I’ve never seen it done and believe most of us hasn’t. I assume that you’ve used a bow to turn the screw? I always thought e should use the screwdriver as turning mechanism but completely wrong I presume was I.
@WatchWithMike Жыл бұрын
What a great demo! Nicely done.😊
@weaves1962 Жыл бұрын
Nicely done. Really well explained. Just one question that I have trouble finding an answer for. What grit abrasive emory/wet & dry do you use to pdress the abrasive "teeth" on the burnisher?
@RandomRestore Жыл бұрын
Thank you for sharing 😊
@spartan076 Жыл бұрын
This series was awesome. I’m still not ready for this kind of watch regulation/adjustment but, I’m glad I have access to these videos when the time comes! Great work! I hope you can make more watch videos in the future!
@johntaylor-oe8fi Жыл бұрын
Do work on watches
@tomc4851 Жыл бұрын
Excellent tutorial video. FYI at 12:22, you use the large barrel of the bench mic for final measurement. If the micrometer nut is properly adjusted and the lubricant not dried and thickened, using the small barrel or knob at the end generally allows easier repeatability. I expect you have more than enough dexterity and attentiveness to use either portion of the barrel. For me, the small barrel provides an additional layer of consistency against my hand being tired or caffeinated. Again, excellent video.
@timelyvintagewatches Жыл бұрын
Hey Tom, thanks, that is a really good comment. You're right, I am pretty undisciplined about using the fine knob. I am trying to rely on it more. A very good point! I am frequently overcaffeinated or tired or both.
@frodriguezpc Жыл бұрын
Great stuff, and a lovely blue dial Raketa as well!
@PilgrimLad Жыл бұрын
Nice job, I'm learning a lot. I also like hearing the birds.
@boydsargeant7496 Жыл бұрын
Hi, nice job. Did you push out the old pin (how?), and then I assume you could measure it, or did you measure the good pin? I don’t have a lathe, do you know if it’s possible to purchase tapered brass for such a job? Ta.
@timelyvintagewatches Жыл бұрын
Hey Boyd, I can't remember exactly how I got the end out. My best guess is I used the staking tool to drive it out. I did measure it, but when turning it in the lathe I did not try to get it to that diameter exactly. I just did a taper pin and filed down the excess after I inserted it in the hole. I think you can buy tapered pins from CousinsUK, but whether they have something that fine, I'm not sure. All good questions!
@jenjiemanalastas5303 Жыл бұрын
Its very informative,nice work explanation,learning a lot
@Mars-zgblbl Жыл бұрын
Thanks for this. Any idea why the impulse jewel should be aligned at 90° to the balance arms? Provided the hairspring collet is aligned properly relative to the impulse jewel, the alignment of the balance wheel shouldn’t matter, unless this is a convention to make it easier to remember where the hairspring collet should be pointing.
@timelyvintagewatches Жыл бұрын
I agree this is likely just convention. I can't remember what I said in the video but I don't think I have ever heard a very compelling reason. One might be that you don't want the impulse jewel under an arm, because you may want to view the escapement action. Another would be that you want to do as little poising as possible, so you should put it back as originally constructed, i.e. 90 degrees from the arms. But I agree that is not in itself a compelling answer why it was set up that way in the first place.
@Mars-zgblbl Жыл бұрын
@@timelyvintagewatches That makes a lot of sense
@Mars-zgblbl Жыл бұрын
Thanks for this! I particularly liked the way you checked end shake for various wheel combinations. Another KZfaqr checked the original internal diameter of the broken jewel with a taper gauge before it could fall apart, and then checked the existing depth of the broken jewel using his Seitz tool, before pressing it out. This way he had a ballpark setting on the Seitz for the new jewel (assuming it’s the same thickness). This might save you a little trial and error
@timelyvintagewatches Жыл бұрын
Hey thanks, those are great suggestions! I will try both of those next time.
@Mars-zgblbl Жыл бұрын
@@timelyvintagewatches Hope it helps. I’m still reading Fried and De Carle and slowly acquiring a few tools, but would assume the “right” way to size the jewel holes is to first polish the pivots using a Jacot tool, then measure the polished pivot with a micrometer, then custom-size the jewels to fit
@timelyvintagewatches Жыл бұрын
@@Mars-zgblbl Yes, 100 percent that would be the right way. One or two hundredths won't be the end of the world but certainly if you were planning on reducing it a lot then you would want to plan ahead that way!
@Mars-zgblbl Жыл бұрын
@@timelyvintagewatches Hi again - here’s another ‘Tuber’s jewel replacement: kzfaq.info/get/bejne/r75-iaxy2bPTpZc.html - now all I have to do is sneak a cheap jewelling set past the purse holder. Cheers
@timelyvintagewatches Жыл бұрын
@@Mars-zgblbl Haha, that's the hardest part. Next to that watchmaking is child's play.
@igorcabrera8123 Жыл бұрын
Best video I found about this subject. Cheers and Merry Christmas from Canada.
@timelyvintagewatches Жыл бұрын
Thanks Igor. Happy New Year - also from Canada!
@stevemahrer7097 Жыл бұрын
As a recently retired engineer, Watchmaking is my new passion. Your clear, honest and intuitive progression of the examination, mechanical triage, clean and repair is very well done. Visual learners like myself find this hugely helpful. Watch repair is a dangerous rabbit hole to venture down, but fun! Thanks and well done.
@timelyvintagewatches Жыл бұрын
Hey Steve, that is a really nice comment. Thanks very much and good luck on your journey!