@@dxankor4136 yea, used to be a pretty good place to go for the weekend, we were walking by the ticket booth and heard them say $85 for a day pass and we told the people there it wasn't worth the money this year.

That's due to the bed Flex on the truck itself. It's obviously exaggerated when it's 4 and a half feet further from the Pivot Point. So far no issues, but only time will tell with anything. I had the same amount of flex with my old setup with my canopy and rooftop tent

@@upper_left_adventures figured some of it was bed flex but couldn’t really tell if it was bouncing. Looking forward to seeing more content!

I drilled three holes. Two for bolts and one for wiring

Yes, baja design lights with the mounts I sell on my etsy

thanks

With my oversized tires, I'm getting around 21-24mpg right now

5/16 drill bit will work as well

Didn't know they had different sizes, just watched their video, I see what you mean. Definitely won't be able to get into the lower bags on anything aside from the midsize truck version. Takes about 2 seconds to drop the table down to access them though.

@@upper_left_adventures I think there's probably a few different ways to make it work. Could lower the bags down on the Mole portion and lose some of that cargo space, could adjust the size of the table to clear the lower bags or maybe even drill a couple holes and move the mounting bracket up just a little bit.

Still no major issues. Have had no issues in winds. I've had it set up in 30ish mph winds

The go to my roof, they are limb risers, keep branches from smacking my windshield and breaking it

Can't speak on xm radio, as I don't use it, but have no issues with regular radio (I listen to podcasts 90% of the time)

Alucabin is 3x the price, and I've had 2 friends who purchased and sold their alucabin after not liking them. On paper, the only think the alucabin has over the lonepeak is the rear door setup

Solid, only the upfitters have raved about alucab. Most end users have moved on to other options. Ty for the mad quick response.

My interior is built with 2020 extrusion, the camper is built with custom extrusions Kyle had made. Unfortunately, they have one major flaw. I believe they did it on purpose, others dont. The extrusion he made is custom, and as of yet, have not found a single source other than lone peak directly to buy t nuts. Its the size of m10 t nut track, but uses m8 bolts.

Ive never slept inside another camper, so dont have a direct comparison. But I can tell you its miles ahead of a go fast camper, and not another camper out there has the passthrough space, and room inside. And price cant be touched by any of the competitors. Camper, if ordered today is about $7500 with all my options.

It's been great so far, only issues I've had they have seemed to fix on the campers being delivered.

Don't run an antenna on the truck, havnt for a few years and havnt had any issues. I do run a ghost antenna for my gmrs and a long rang antenna for my weboost.

Appreciate the order! Will go out tomorrow!

With the diesel heater going, none. Havnt spent any nights in it yet without it going

Up near cle Elum WA

Why do you say that? Lol

Ovs 270

I've got a second printer on order and should be here next week. I definitely thought that I'd have him up for a couple days to sell the few that I made and they all sold within an hour. I'll have some more up on Monday or Tuesday and once the new printer gets here I should be able to keep up with demand a little bit better

@@upper_left_adventures looking forward to it!

​@@4wDegenson etsy, only 5 sets of covers available until next weekend when the new printer is here.

@@upper_left_adventures hell yeah, got my order in! Thanks for the heads up!

@@4wDegens appreciate the order, will go out tomorrow

Planning on making more. Thought they would be up for a day or 3 and sold out in under an hour. Ordering a second printer so I can get more out.

Ye same. Wanted to pair it with the diesel port as well 😢

@@jtaco66 should have both restocked at least a few of them this weekend

​@@jtaco66both up on etsy, only 5 sets of covers available until next weekend when the new printer is here.

on etsy, only 5 sets of covers available until next weekend when the new printer is here.

It's a short bed, so believe it's just over 5'

Most likely from the loose bolt. Will see if I have any more issues now that eveything is tight.

Table is a tailgater tire table, Gaia I usually run the Overland overlay, sometimes the satellite one, and sometimes the usfs overlay. I'd say good weather 55% of the year lol

@@upper_left_adventures interesting info about your 'table' but I was wondering about your "tablet" haha...😁

@@NigelNaughton totally read that wrong lol, playing with the kids haha. Tablet is just a cheap Samsung tablet I had in the drawer in my office collecting dust.

@@upper_left_adventures I always prefer an Android tablet, especially for this application as you can expand the storage easily. As long as it has built in GPS (LTE models). Thanks!

@@NigelNaughton luckily, all Samsung galaxy tablets have GPS even the non-lte ones which is what this is. Think it's a tab a7

Think I'm going to loosen all the bolts a little, get the fitment right, and then tighten it all again and see what happens.

I have had my Lone Peak since December with no issues of sliding. I also purchased two extra pucks. I have a Tacoma so it uses a different mounting system compared to the Chevy.

Just a random Chinese diesel heater I grabbed off Amazon 3 years ago

I cut a 1' chunk off a strap, took a lighter to a nail and put a hole through both ends, and attached it with one of the screws already in the tail gate.

Yeah, it's fully possible. I'm going to bring it up to them when I see them at the Overland rally in June

Boost auto with all the options at the time (3 years ago)

Im planning on going up to the scales on Friday on my way out of town to get a packed weight. Will be in my video next week.

Hopefully will be offering them up forsale, but will make a post on the fb groups as well as on here if we do.