Very helpful video with clear instructions. I had the E01 F03 code and I needed to reset it otherwise the drain pump would keep running. Thank you very much for sharing your knowledge!

Thanks for the video. I have a LG Refer # LMXC23746S/01 Date: April 2018. Linear Compressor (pink label) FLB075LBNA. I have checked everything as mentioned on this and other videos. I tested CAP at 19.89 micro-F; #3-way valve is bumping at startup; start relay has continuity; all fans work in Test Mode#1. No blinking led from Printed Circuit Board (PCB). Coil was not dirty. Compressor runs quietly without being hot. Checked voltage CON201 [COM to POWER] under normal plug-in at 123.5 volts AC. Unplugged, disconnected CON201, re-plugged/power, measured voltage ramping on [COM to Power] on PCB at CON201 during Test Mode #1. Ramps up to around 120 Volts and then drops off after about a minute. In this time, the Error LED flashes 3-times (red); this is likely due to disconnected CON201 male plug. Unplug unit, reconnect CON201 Male and power up unit with no error LED, same Compressor mode with no cooling. No heat or cold on compressor tubes. My questions are 1) Should I get some cooling at or near 120 volts to [COM to POWER] leads to compressor at PCB posts? Does my troubleshooting point to a bad PCB and Compressor Failure? Should I fix or buy new?

I replaced the hall sensor, and it throwed off the same code immediately

I wish I would of know there was a spring to the drum would of saved me so much time knowing why it wouldn’t stick 😅

Can I just say how grateful I am that you showed how the belt goes back on, cause you made it SOOOO much easier for me to reassemble my now heating dryer? Thank you!!

Can you please provide the link where to purchase?

I performed a test and the ice maker spun around and out came a thick block of ice. No way that block of ice was going to be dispensed. I looked at it several times throughout the day and the ice tray looked normal. It was deceiving. Getting rid of that block fixed the issue of it not dispensing ice. Thank you.

First , thank you for this video. I found a stupid fault on a similar model. I had to remove the burner top to get the control panel out. What I found, was that 3 controls had had the mounting screws come loose, leaving the controls free to rotate, and not turn on a burner. I found more loose mounting screws. i put them all back with Locktite.

I have an LG LDF5545SS dishwasher. I'm hearing a noise similar to this: kzfaq.info/get/bejne/gcCZjbODmtm7lWQ.html&ab_channel=BrianHawkins. I suspect the motor is going out as I've had the unit for 4 years. I found this part number in my searching (ABT72989206) and I wasn't sure if you'd be able to confirm this part is compatible with my model. Thanks!

Thank you very much It saved me a big headache Keep it up

Had a old green cleaner pad clogging the filter of the drain trap + pennies, rocks, srews and gunk! Had hard time to figure how to srew the trap back in place, you have to put the right part of the filter at the bottom and top, but finally did. No more error code! Thanks!

My LG is not cooling to the set temps. Fridge or freezer. I ran the test and both fans came on full blast. But, out of test mode, nothing again. Thoughts?

I have the same model. It is 4 years old. I bought a new motor/pump for $294. Easy peasy to install.

Your instructions to clean the little air bladder and the trap has completely solved my problem , I thought I needed a new machine. Alarm is cleared and machine works great again. Appreciate you!

This video was amazing from start to finish as a sports mom or 4. I've never once a day in my life thought I would be taking apart my dryer and did it step by step with the video. Thanks for making. The only thing it cost me was $25 and about an hour. And my element from Amazon came with extra thermostat and other parts

Hi there, I got the same E1 F9 error code. I have emptied and cleaned out the drain filter- a dime, an old money clip and hair ties inside. Tried running the quick diagnostic and it stopped again at C7. Drained it again, this time popped off the pressure switch hose and black bladder and it was full of gunk. Cleaned it all out and re-attached. Ran a spin and drain cylcle with no code thrown, but the washer was empty.....Then I ran a normal load and it stopped at min 34 out of 43 and same code for Long Drain. Would you advise a new pressure switch and hose or should I just go for replacing the drain pump? I suppose I will look into ordering both parts since my manual doesn't really tell me how to decipher between the two possible problems..... Any Suggestions? Thanks for the great video!

Thanks for the video! I see all the cockroach bodies and poop lol ... seen that a million times on refrigerators, yuck!

I have a code that keeps popping up E1 F9 do you know what that is

We replaced a rotary switch 6 months ago and now we have burn marks on the new switch and it's not working properly again. What could cause some burnt marks on the new switch and wire connected to the switch?

Yup every single. Day. You get pretty fast at it. Lg refrigerator compressors and washer pumps etc get pretty simple after a 1000 of them

Hello sir! Thank you so much for the tutorial, why do you need to replace the pressure switch hose if it is the two other hoses rubbing together? (I replaced the two hoses and now I’m having other issues, think it’s because I didn’t replace the pressure switch hose)

Hi. My washer is leaking some brown slime from below the control panel, do you know what it is?

Thanks for this video. Instructions were super easy to follow

So the same relay board can cause the fan to not operate as well??

I can’t recall ever seeing one of those switches go bad however I have seen the black hose gets smashed at the very top bracket from the heavy lateral movement It’s just as bad as having a restriction it gets flattened. Thank you for posting this too because I forgot how to clear codes on this model and someone removed the Bible ( tech sheet) smh😢

These lg fridges are terrible. Ours just died after exactly 6 years. $2,000 junk. Never buy anything LG.

When 5 minutes job you want to do in 1 hour ? 😅

Thank you. Replaced my heater assembly with you walking me through the process. Much appreciated.

Awesome job. Thanks for sharing. Plus . I learned about shortn out .. even tho it's plugged out

My lock is clicking a few times before the de2 error shows up. Does that still mean the locking mechanism needs replaced? Or does that point to something else?

Great video, however I just saw another internet video that avoids removing any panels. Instead, you disconnect the power and two water lines feeding water to the washer (at the washer). Drain the filter tube. Remove the cover in the filter tube area (as shown in this video). Then position the washer so you can tilt it backwards approximately 30-45 degrees; enough to allow you access unearth the washer. Then remove the three screws in the front of the pump (if all three are present, mine weren’t) and the screws underneath. Then you can remove the pump and all attached parts easily from underneath. The biggest caution is bracing the washer so that when you tilt it, it cannot slide and fall. Mine is leaning against the wall.

Thank you very much! I followed your steps and changed very easily. Thank you very much once again.

Awesome video!! I'd love to attempt this but I live in a condo without much space & I don't have the tools. It would be great if I could take it to a space with tools & some help to complete the repair. I could easily buy a new dryer but I don't like adding to landfill for no reason. I called 2 appliance repair companies & they won't return my calls after I tell told them that the unit is stacked on a washer & it's in a closet. I offered to help move it.

I wanted to take the time to thank you. I have the same dryer. Had it for about 3 months.. and then it stopped heating. 😫 Did some basic research and decided it was either the thermal fuse or the thermostat itself. I found your video and followed it step by step and I was able to replace both and my dryer is back!! Thank you again!!

Thanks I have a stacked unit. Will the back come off while the dryer is on top?

Thanks, your video 0:31 was helpful & it was an easy repair. Your suggestion and hands on with video made a big difference when doing my job.

Great video. I have a similar GE fridge and have been having issues for 2 weeks. Initially the fridge wasn’t cooling as much so repair guy changed out the fan. Now fridge is over-cooling. Thermostat, sensor, and damper were all replaced. Still have the over cooling issue for the fridge. Only have 2 days before the fridge is hauled away and new one is delivered. I did the diagnostics like shown in this video but no idea what the information means or how else to test. What could be left as the problem- control board??

I am extremely disappointed with LG, I am having the same problem and the dishwasher is less than 3 years old. we had another problem with LG TV that stopped working in 2.5 years. I would never buy LG ever again.

The motor LG warranty 10 years, in fact only 1.5 years for my case.

I had the same slow oven preheat problem. I have similar model, LG LRE3061** . Probably 4 years old. Opened up back of unit as you did (thanks for the video) . I found the white 14 AWG wire on the broiler heating element was nearly open, just hanging on by a copper strand or two. The crimp connector was fairly black and a tad bit greenish. The first 1/4 inch of wire insulation was charred black as well. I cut the wire 1/2 inch and stripped the wire 1/4 in. for a new blade connector. But the copper wire strands were heavily oxidized (black). I believe this is not unusual over time at elevated temperatures. I cut back an inch and a half to find good copper wire. I added a short piece of new 14 AWG wire and crimped on a new blade connector. I didn't have any 90 degree blade connectors, so I bent the one I have to 90 degrees. I put it all back together and the oven works like a champ now. Thanks for the video! $8 for small roll of 14 AWG stranded copper wire, and a few dollars for bullet connectors for the wire splice and new female blade connector. I could have used a butt splice, but I prefer bullet connectors.

So your first test did make the ice maker go into harvest mode, why did you replace the entire icemaker anyway?

This is wrong

Ordered my heating element, looks simple, I'm going to try it while it is on top of the washer. Hopefully that won't be a problem.

The only issue is the pump price. I mean lg sells it for $ 300 & that is not far from the price of a new one. Great video, thanks

Quesiton, My evaporator fan isn't working even with switching out a new one and my coils are not cold at all. Also, my refrigerator is about 75 degrees and my fridge is 65 degrees. Do you think this could be inverter related? Thanks so much.. trying to find a volt meter around the house now.

Thank you for this video. My linear compressor has gone out, just beyond the 10 year parts warranty (it lasted 10 years, 8 months!). Can you estimate what it would cost in labor and parts to retrofit it with the new LG-approved compressor? Thank you!!

Thank you for this video! Was able to fix my old LG washer by replacing the door lock. The de2 error code went away!

Thanks for the instructions. Water pump went out with the OE message. Fixed it thanks to you

Great video! I already did the belt on my GE washer and I'm considering replacing the motor. You make it look so simple, and I appreciate that. Thank you!

Thank you sooo much it was very helpful