To make this easier for you put those bearings in the freezer for about an hour.... then put the two halves of the crankcase in an oven or even out in the sun if you live in a warm climate for around 30 minutes or so not a lot of heat Maybe 150 to 200 degrees if you're using an oven... the bearing will just slide it right in no tools required just tap it in with your rubber hammer and I do mean tap you will not have to hit it hard it should slide right in with your fingers if you got a glove on
@jamiecook3966Ай бұрын
I have been wrenching on machinery and motorcycles forever and never heard of these links, thank You!
@mantishalen53032 ай бұрын
Couldn't help but notice this guy has no inline filter
@kenwileman63733 ай бұрын
I have missing teeth on the smallest tooth wheel of the two on the right side of the engine, how do you get those peices out?
@adamsmy81215 ай бұрын
What kind of carburetor is that? Whats your top speed? I cant get mine over 26mph
@joshjoshua64796 ай бұрын
What occurs with the its electricity when the magnet is incorrectly installed?
@ibkraft67062 ай бұрын
I doubt it affects much if anything is literally just a magnetic coil
@stephenmichaelolney58809 ай бұрын
This was so much help as I am knew to the game piecing together engines, thank you
@RightLane39310 ай бұрын
that what i did, but it still a little slip and it doesnt work for me.
@leemilica11 ай бұрын
How the fuck do you remove the clutch nut? I HAVE BEEN GOING AT IT FOR THE PAST 2 FUCKING DAYS USING THE BIGGEST WRENCH AND PLIERS I COULD FIND AND I BENT THE 3 PINS LIKE 15 TIMES ALREADY AND THE FUCKING NUT WONT LOOSEN
@trevorread866811 ай бұрын
Where can I find a replacement shaft the gear goes onto I picked a bike up that the nut and bolt on the chain side are stripped to hell😅
@MrMohamed323 Жыл бұрын
Is the flywheel in the engine sufficient for the piston to rise up to compress the mixture and complete the cycle?
@PaulyFSF Жыл бұрын
slow no torque i have a shittier setup with a larger sprocket and i hit 40mph np
@wojtech270 Жыл бұрын
Thank you!!!
@CUBANIDAD Жыл бұрын
Your video skipped the hardest part!!! "I already have it loosened, so I'm just going to remove it by hand." HOW DO YOU LOOSEN THAT SHIT?
@MikeNBikes Жыл бұрын
I needed a straight to the point video like this, thank you.
@michaelbrinks8089 Жыл бұрын
My teeth wore out quick. I'm gonna order one but this time heat treat & temper it. Like I did my rear sprocket which has same mileage as front sprocket but has no major wear yet. All you need is propane torch or Mapp gas & simple heat treat/temper instructions. They bother to heat treat them in China in order to keep manufacturing down + u end up buying another one sooner. Just thought 💭 It'd be a good idea to heat treat the puller tool also.
@stanislavbryndza Жыл бұрын
Takto môže meniť ložiská len amatér!!!
@irondan007 Жыл бұрын
my suzuki zeus 125 cc bike has vm 18 mikuni carb. On the left side of the carb just below the choke lever there is one rubber diaphragm(engine side) fixed diagonally with two star screws and also some sort of an electric switch top side which goes to the cdi unit ,(two wires) .Please explain the exact function of these parts ?
@tallishadley624 Жыл бұрын
Mine doesn't have a thread for the tool how do I remove it without the tool???
@blackout260112 Жыл бұрын
Nice wheels!!!!
@korymay3126 Жыл бұрын
thanks for the info and link,
@sebastianlorant6502 Жыл бұрын
"standard master link and use the 415 half link" what is the difference?
@tinypurplefishesrunlaughin8052 Жыл бұрын
Performs like sh!t looks like sh!t. I’ll never install that fixed tensioner. And as far as we are talking shitty looks and performance get a load of that RAG joint sprocket crap. jeez Whatta piece.
@Op1zilla Жыл бұрын
Short an easy, 😁👍
@lifesadventureskeepingitre1180 Жыл бұрын
I'm new to the motorized bicycle and I'm finding it very interesting especially working on these small engines you were very informative good job.
@MeiGunner Жыл бұрын
i cant Get the Bolt off ,, lol
@BicycleMotorsports Жыл бұрын
Just use a socket wrench and turn it counterclockwise it should come right off.
@MeiGunner Жыл бұрын
@@BicycleMotorsports yeah ,, it Was a motor from when i was A kid in the 1990's .. and when i open it , it was All rusted on the Magent and The Coil ... SO after some Pb blaster , and a new Coil , its running good! ( no New Magnet , just CLeaned it with Sandpapper ) God Bless stay Safe out on the Road
@leahresnik9208 Жыл бұрын
Also, what engine did you purchase for your motor bike? In your video you were talking about how you upgraded the carburator? Can you please provide more information on that? TIA!
@BicycleMotorsports Жыл бұрын
I have a CNC Billet aluminum motor on there now that I assembled myself with balanced cranks and upgraded clutch. However the carburetor I upgraded to was a Mikuni vm18 clamp on carburetor. Just below is a link. I purchased it from treats. If you check out some of my other videos You'll see the carburetor www.treatland.tv/mikuni-vm-18mm-p/mikuni-18mm-vm-round-slide.htm?gclid=Cj0KCQjw_viWBhD8ARIsAH1mCd6SBWvJkXb7ErgKipjgGpxD4ccCKSHxfSAVh_uyXRm5WiMerx2Np8IaApHdEALw_wcB
@BicycleMotorsports Жыл бұрын
What kind of setup do you have?
@BicycleMotorsports Жыл бұрын
When upgrading to this type of carburetor just know it's a little more complex than the stock carburetors that come with these motors. You might have to tweak it with the jetting and fuel intake and in some cases the fuel float. I've made a few videos addressing the aforementioned.
@BicycleMotorsports Жыл бұрын
You're also going to need an 18 mm intake manifold for the motor to match up with the upgraded carburetor
@BicycleMotorsports Жыл бұрын
Here's a link to another video I did on a sprocket removal and you can see in the video the reed valve setup that I have that the Mikuni carburetor would connect to. The Reed valve will help immensely with fuel blowback into the carburetor which can mess up the fuel to air mixture ratios and cause fuel leaking out of the carburetor onto the bike frame. I recommend a reed valve. you might have to change the carburetor jetting. kzfaq.info/get/bejne/gryXobiXuNW1e6s.html
@peepeecaca69262 жыл бұрын
I snapped i peice of my engine block doing this
@BicycleMotorsports Жыл бұрын
What piece?
@peepeecaca6926 Жыл бұрын
@@BicycleMotorsports the top right screw hole the whole thing snapped of I just have 2 bolts holding the clutch arm cover on it works
@Billy-ky8qc2 жыл бұрын
How can you tell if your engine is 8o.cc. Or 50.cc
@BicycleMotorsports2 жыл бұрын
For whatever reason these China girl engines are 66 and 80cc used interchangeably. Most people just refer to it as a 66cc
@eddiemarines58612 жыл бұрын
We're can I get the woodruff key and is it m.m.or in.s or what size?
@BicycleMotorsports2 жыл бұрын
You can get Woodruff keys from bikeberry.com or on Google search bar just type in 66cc engine Woodruff key. They are standard size for those engines.
@ryanmckenziegilbert49502 жыл бұрын
Do I have to pull it off to put the chain on
@MrMohamed3232 жыл бұрын
How can the bassum go up in the compression stroke, given that it is only one?
@linkgroundwalker2 жыл бұрын
In your case I don’t think replacing it was worth it, in about 3 months or less you’ll have the same play in it. Ride it until it tells you something is wrong by puking it’s guts out or screaming.
@joneserupinsmoke91612 жыл бұрын
Bro heat the end of expansion chamber up with a hand torch and then bend it in towards the bike or you can just put a 20 degree angle elbow on it or something
@joneserupinsmoke91612 жыл бұрын
Is the seat spring loaded?
@joneserupinsmoke91612 жыл бұрын
Bro when you use the high performance exhaust the expansion chamber or whatever you were using with no baffle you cut the muffler off of the old stock ones and use that baffler
@joneserupinsmoke91612 жыл бұрын
Bro I had the same issues on one of my builds bit yeah best bet jist replace it it's just gna keep happening 👍😃 thanks for information though bro
@Nostalgik642 жыл бұрын
Your also supposed to add a lubricant preferably grease to lubricate the threads on the Clutch Gear Puller to prevent any cross threading and to make smooth contact with threads.
@garygushue42732 жыл бұрын
Thank you so much I was trying to figure out how to get the chain off without depressing the clutch as I found this motorized cruiser in the trash & fixing has been fun
@OddBallPerformance2 жыл бұрын
For anybody that watched him install that bearing. Please, never ever ever ever ever install a bearing into a case by pushing or pulling on the inner race. Use the old bearing, or better yet a bearing installer tool, and apply only pressure to the outer race. Pushing/pulling on the inner race will distort the cage and potentially shorten bearing life.
@rivermccarthy21302 жыл бұрын
Hi, not sure are you still active but the gear removal tool stripped it and gave you any clues how to fix it?
@kenpottinger64792 жыл бұрын
Can't get the nut off clutch plate
@buddahmayne92732 жыл бұрын
What you using for the tensioner where the chain goes on?
@anonymousproductions17922 жыл бұрын
A lot of big words in this video damn
@flodag72882 жыл бұрын
Yes I bought this half like but the master lik don't fit
@flodag72882 жыл бұрын
Yes I bouthbthis half link but the master link don't fit
@flodag72882 жыл бұрын
Yes I bought the half lenth but the chain replacement don't fit