John Deere X300 does NOT have a bad transmission but a sheared pulley- inspect trans & change pulley

Рет қаралды 8,349

Ellis Mowers and More

Күн бұрын

Пікірлер: 43

@elijahbey3366 2 ай бұрын

Holy cow. That mower looks like it sat on the ocean floor with the Titanic for 100 years.

@duainabbott7746 21 күн бұрын

Hello, I just wanted to thank you and let you know that I’m going to subscribe to your channel. I helped a friend with a John Deere X 300 and after watching your video we realize we probably had a stripped drive pulley. After watching your video, we also realize we can access that drive from the rare by taking the spring tension off, removing the clip and getting a new pulley putting thedrive belt back on the pulley and the tractor runs just fine now thank you very much for being thorough and also not charging that other gentleman for a transmission that he did not need you are awesome. Thanks.😊

@EllisMowersandmore 20 күн бұрын

Thanks for watching, glad I could help you all out!

@TTT-du6oj 10 күн бұрын

Always good to see a honest man👍

@philliphall5198 Жыл бұрын

Your honesty is wonderful 😊

@butler386 Жыл бұрын

Thank you for being an honest person. Great job.

@daveerrington5166 26 күн бұрын

Not only is the pulley stripped, but the transmission gear coming out of it also is stripped. You have to weld it. Also, you should’ve changed the transmission fluid while it was out just my two cents.

@e.t.preppin7084 2 ай бұрын

Non text was on top. Thanks very much. That’s what I needed to know. Thanks for being honest but you didn’t have to do any of the work you did. Live and learn I guess. Don’t even have to pull the tension spring off.

@philliphall5198 Жыл бұрын

You should build a rolling A frame to lift up the mowers which makes it easier to fix , remove bat, oil and seal gas cap with plastic bag , upupup and away

@liljoeii6091 Жыл бұрын

Awesome video thank you for the video

@KensSmallEngineRepair Жыл бұрын

Love the new intro!

@EllisMowersandmore Жыл бұрын

Thanks Ken! It was time for a revamp!

@robertmailhos8159 Жыл бұрын

It would be nice if you had a mower lift to raise the mower high enough to work on it while you are standing up but you can get it done while you are laying on the concrete

@e.t.preppin7084 2 ай бұрын

Two 8 mm screws loosen and flip gaurd. Remove snap ring and replace the pulley.

@Hear-MeoutTwo2 9 ай бұрын

You missed the opportunity to change the transmission fluids while you had it off the mower. Changing the fluids will extend the life of that transmission.

@mavarbor 2 ай бұрын

Thanks so much for making this video, if I might ask where are you located where could I order or pick up that transmission pulley from other than possibly from John Deere?

@EllisMowersandmore 2 ай бұрын

I'm in Durham NC. I have a link in the video description to the pulley you need.

@wallyblackburn 10 ай бұрын

Don't understand why they couldn't put a tapered pin or a key on this to prevent either from wearing out!

@mrjunkp7090 2 ай бұрын

The splines stripped because its a bad design. They were not that tight to begin with and they rub a little with each turn of the pulley. Dont forget the belt is pulling tension sideways. So eventually the splines wear. More so on the pulley than the input shaft of transmission. Should have been keyed and set screwed or something more sturdy.

@philliphall5198 Жыл бұрын

Now that lifting is bad on your back and you’ll end up like me!!!!!!!!!

@jimsevigne8536 11 ай бұрын

If you knew it was a bad pulley in the first place, could you have taken the actual seat and metal body off from the top to gain access to the pulley to replace it? Just curious if that would work also.

@EllisMowersandmore 11 ай бұрын

You probably could have accessed it from the side without taking anything off. Having a stubby impact driver would almost be a must unless you could figure out how to keep the pulley from turning so you can turn the nut.

@MrTactiCALi 11 ай бұрын

X300. I have a high pitched grinding noise in forward and reverse. No movement when pedals are pressed. And ideas? Pulley??

@EllisMowersandmore 11 ай бұрын

That's the same symptoms this machine had. See if there's a lot of play in the pulley. I bet that's what it is.

@2loonscalling437 11 ай бұрын

So my x300 stopped moving while mowing a few weeks ago. It makes a high-pitched sound, and barely moves. I cannot drive. Belt still on and the pully seems to be turning along with that fan when I push the pedal. Won't go forward or reverse. Does that sound like the transmission?

@EllisMowersandmore 11 ай бұрын

You may have a sheared pulley too from the sounds of it. The pulley will still turn but the gears inside the pulley won't connect to the shaft on the transmission. If you can, take the belt off the transmission pulley and remove it. Pretty hard to do unless you have an impact, but at least by taking the belt off you could see if it has a lot of play and grabs onto the shaft.

@premium1188 10 ай бұрын

i was towing a small trailer with some stuff in it, and it just completely stopped in place and made some weird noise in the rear. Whenever the pedals are pressed, there is zero movement. Would that also be that pulley in the rear?

@EllisMowersandmore 10 ай бұрын

See if that pulley has a lot of play in it. If so, see if you can take it off. You should be able to with it still on the mower. That's probably what happened. Especially if yours is an early model X300 from around 2010 or so.

@premium1188 10 ай бұрын

@@EllisMowersandmore yup. that pulley has play. i’ll replace that this weekend. thank you

@gordbaker896 2 ай бұрын

@@premium1188 Good luck.

@transistorradiorecords3661 14 күн бұрын

I am dealing with what I believe is the same thing with my John Deere s240. Can't you access this t- pulley by either the black carriage or by removing one back tire? TY

@EllisMowersandmore 14 күн бұрын

You should be able to. I have been able to on similar series mowers like the L, LA and D series.

@transistorradiorecords3661 14 күн бұрын

@@EllisMowersandmore Thank you!

@philliphall5198 Жыл бұрын

I think it’s just easier to pull wheels and have plenty of room but each his own Do you work on very many Zero turns ???

@EllisMowersandmore Жыл бұрын

I get a few to service and repair for customers, only had about 3 to resell.

@RK777PL 2 ай бұрын

How many hours on this machine I'm just curious also I got a x350 with the Kawasaki how long you think it's going to last if I take very good care of it and I mean good care of it I'm very particular kind of guy I do oil changes every 50 hours air filters and everything else every hundred

@EllisMowersandmore 2 ай бұрын

This had around 400 hours. These are known to go over 1000 hours with minimal issue when taken care of.

@RK777PL 2 ай бұрын

Yeah I heard 2000 hours is possible as well

@e.t.preppin7084 2 ай бұрын

I just need to know if it matters which side faces up on that pulley. Anyone

@e.t.preppin7084 2 ай бұрын

Total success by changing the pulley. Just like a new mower. Thanks for the tidbit of information ℹ️ needed. I’m grateful that I didn’t have to go through all that for my repair. I’m grateful that you did so well didn’t have too

@philliphall5198 Жыл бұрын

With just a ring it can move alot Be much better with a nut

@Dirtywhtboy87930 2 ай бұрын

Didn’t you say that tranny had some leaks? While the trans was already out and pulley off, I would have popped off the fluid fill cap to check the level of fluid and topped it off. Think you supposed to fill it within.75-1” from the top of the fill opening. If it’s low then filled up, will lengthen the life expectancy of that transmission.

@Dirtywhtboy87930 2 ай бұрын

Not only does fluid build pressure to function, but also serves as coolant to keep it from getting too hot and causing parts to prematurely fail…