Milwaukee M18 Fuel High Torque Impact Wrench Repair, it has no strength

Рет қаралды 36,544

NEL SERVICE

3 жыл бұрын

Music: Electro-Light - Symbolism [NCS Release]
Facebook: / nel.service.electronics

Пікірлер: 53

@hectormendoza4158 2 ай бұрын

Amo las herramientas inalámbricas de calidad como estas Milwaukee 😊

@CrotchetRocket 3 жыл бұрын

Dude those vice clamps are priceless! I’ve used mine in so many repairs too, it’s the tool capable of healing tools!

@arthurflores1605 Жыл бұрын

Thank you for the teaching. It was easier than I thought. My M 18 fuel half-inch drive impact seem to have got some trash in the rotary blades in the back of the unit. The noise it made sounded like this unit was done. Thank you again for the tutorial.👍🏽👍🏽👍🏽👍🏽👍🏽

@MrZimmaframe 2 жыл бұрын

Hey thank you for taking the time to make these videos for others to see.

@theeabster1983 3 жыл бұрын

And thank you very much for the video.

@jasonhuhare 2 жыл бұрын

So great video. I can learn a lot about restoration of Milwaukee. Thanks for your share a lot.

@Popajaja 9 ай бұрын

Question for Milwaukee specialists: I have a Milwaukee M18 FMTIW2F12 that has an interesting bug. When I press the switch, the machine spins and diode number 3 (third gear) lights up for a long time. Only when the diode turns off is it possible to change the direction of rotation and start again. In addition, the maximum speed (diode number 3) cannot be changed. In order for it to work at all and not to wait for diode number 3 to go out, I remove and put back the battery. That means to change the wheels on a car that has 5 screws, I have to remove and put back the battery 10 times. Once I press the switch, I must not stop until the job is done, otherwise there will be a long pause or re-inserting and removing the battery. Impact wrench M18 FMTIW2F12 with 881 Nm loosening torque and 745 Nm torque Extremely compact design with a length of only 152 mm. Which I found in the trash (500 $) that I want to fix... ................. Eureka! I repaired my impact wrench today. The error was in the brown main switch. To make it even more fun, I found the machine and the spare part in the trash. Maybe my experience will help someone who has similar problems? Greetings from Switzerland

@hectormendoza4158 2 ай бұрын

Que bueno que la reparaste wow!

@Popajaja 2 ай бұрын

@@hectormendoza4158 Afortunadamente, arreglé otro taladro Milwaukee M18 (SDS) pesado y costoso enjuagando el interruptor principal con gasolina.

@allywilkeforsenate 2 жыл бұрын

Would have rather had someone speak than listen to the chipmunk music.

@juliogonzo2718 2 жыл бұрын

Chipmunk music 😂 that is perfect!

@jferreira5096 11 ай бұрын

How did you get the bearing off the spring ? It’s quite tight to get a bearing puller on there… just shows you putting the bearing back on

@juliogonzo2718 2 жыл бұрын

That thing has been around the block a few times

@suzesiviter6083 2 жыл бұрын

Anyone know about the pin outs on the m18 battery? you get a voltage between the two inner pins of 3.2v, however my impact sometimes stops working and then I check the inner pins and they are at 0v, i can reset the battery by plugging it into my drill to bring them back up to 3.2v then it works again, so the impact must detect a fault and tell the battery to disconnect the pins?

@dagopelaez1951 2 жыл бұрын

Friend, how are you? congratulations for your work, I would also like to do the same with my milwaukee drill, you know mine is 3/4" but I want to convert it to 1/2" do you think you can help me find the parts I need to achieve the conversion? my drill is the same as yours, thanks if you need more information let me know, have a good day!

@marioarenas2907 2 жыл бұрын

How did you remove the bearing?

@ulyssescisneros3044 Жыл бұрын

Could I know what kind of Grease are you using

@me-pv4fn Жыл бұрын

Were can u get these kits from please as mine is on its way owt thanks.

@EddieSwaggy 2 жыл бұрын

Thanks for the video man! Just wondering instead of putting 3/4 where you put yung socket can you put 1/2 instead is that possible?

@Jultsu Жыл бұрын

not really unless you change the whole outer casing, since the shaft on the 1/2" is smaller in diameter, it won't even begin to sit correctly against the hole for the original 3/4" anvil

@EddieSwaggy Жыл бұрын

@@Jultsu ohh okay thanks bro

@-7205 8 ай бұрын

@1.29 in the video he has all the planetary gears, wafer bearing, Teflon rings laying on bubble wrap... left out a few steps... also: is that Mobil XHP 222 grease?.

@lightshine6044 2 жыл бұрын

3:53 Can you tell me brand name & part number of grease that you are using? Thanks

@nelservice6579 2 жыл бұрын

is a Vaseline from "Divinol Lithogrease 2B" and the lithium base for gears, is slightly more viscous than that used in rotary hammers.

@abcd99949 2 жыл бұрын

I o u

@bernacarrizal3434 8 ай бұрын

Donde tienes tu taller me interesa reparar un torque de 1/2

@lindsaylindsay2627 3 ай бұрын

I have the same issue. I have a 3/4” drive . Can you tell me the part number?

@marion1600 2 жыл бұрын

Where did you get spare parts? I have a same issue

@IDABAYAREA650I Жыл бұрын

*Dont you love it when KZfaqrs are assholes and dont reply and help with helpful videos..*

@conorgrant1928 13 күн бұрын

How does oneself get in touch with you to fix mine?

@erginyilmaztenor 2 жыл бұрын

Thanks. Which grease do you use?

@harisyoung4110 2 жыл бұрын

Look like a normal synthetic blue lithium grease.

@jasonhuhare 2 жыл бұрын

You can buy Wurth High temperature grease for machine. The color of the grease is blue.

@Lord_Mac 2 жыл бұрын

At the end of the video when you ran the screwdriver through the anvil and pulled the trigger. Is it normal for it to make those impacts without it turning on you? I have a mid torque impact and I can hold the socket in place while hearing the impacts on the gun

@juliogonzo2718 2 жыл бұрын

Yeah that is normal. It is not a direct drive. The hammer loads up and skips over the anvil and spins and strikes it. The hammer blows on the anvil create the torque. See if you can find a slow motion video of how the impact mechanism works. It's cool

@BRENDAJASON1 2 жыл бұрын

Well quess that’s mine needs my motor us fine but mine won’t even take a lug nut off anymore snap on 1/2 and snap on don’t even make the parts no more for it or so they say

@silinusvers 3 жыл бұрын

Does it void the warranty to open it up? Saw a forum of someone who opened up their Dewalt to find it dry of grease, just makes me wonder

@nelservice6579 3 жыл бұрын

In general, the warranty is lost, now it also depends on who makes the tool warranty

@nelservice6579 3 жыл бұрын

if you think it would be a problem you can take it to a dewalt service for warranty and they will lubricate it if necessary

@juliogonzo2718 2 жыл бұрын

Don't tell them you took it apart 😁

@juancruzdelcerro6049 2 жыл бұрын

Does the parts are available on ebay?

@nelservice6579 2 жыл бұрын

from a milwaukee parts dealer

@theeabster1983 3 жыл бұрын

What type of Grease do you use?

@nelservice6579 3 жыл бұрын

Grease for gears, high temperature resistance, medium viscosity, any type but do not use graphite grease

@michaelsheridan2656 2 жыл бұрын

@@nelservice6579 why not graphite grease?

@nelservice6579 2 жыл бұрын

@@michaelsheridan2656 Graphite Vaseline is used for mechanically stressed bearings and elements, for sprockets and mechanical elements that work at high frequencies or high speeds, more fluid Vaseline is used. if you put graphite Vaseline on a rotary hammer, it is destroyed prematurely

@MrZimmaframe 2 жыл бұрын

@@nelservice6579 Would molybdenum Grease be ok to use?