Super Engine - Barra Build Pt 2

Super Engine - Barra Build Pt 2 - MS ENGINES

Рет қаралды 4,256

MS Engine Reconditioning

10 ай бұрын

Part 2 of 3 of the Barra build Series - You can find videos from all our series at ‪@MSEngines‬

Пікірлер: 22

@oscarbear1043 7 ай бұрын

Great you showed us how to do a good job without spending an absolute fortune. I know I don’t even need an engine stand thank you.

@thewholls7176 10 ай бұрын

Good job mate Ive got a 5.4 3 valve V8 that wants a freshen up i think ill bring it past the workshop for a quote…..

@Jimmyk63 10 ай бұрын

Great stuff second part 👍

@tasman1340 10 ай бұрын

That's a another great video from Mick

@closertothetruth9209 10 ай бұрын

thats why im here, watching a perfectionist and learning a little here a little there

@cokhialoclongkhanhdongnai4560 10 ай бұрын

❤vip

@cokhialoclongkhanhdongnai4560 10 ай бұрын

Thât tuyet voi

@Marco_A_Marcano_Soto 10 ай бұрын

Primero, Gracias Mi Amigo

@karloswhiskay6550 7 ай бұрын

Didn't even check clearance on pump gears 🤷

@TheXTREMEGROOVES 3 ай бұрын

mate you did not torque the allen key studs on the oil pump or check clearances. you did not set the timing chain up properly either

@Hapkido82AUS Ай бұрын

Lol it was a 11 minute video, there was hours of work condensed down

@MrArty250 10 ай бұрын

What’s a rebuild usually cost approximately

@CAIDMASTEROFPYRO 8 ай бұрын

Talking about people charge a fortune, What would you charge for something like this, machining and assembling a Barra? I've got a standard turbo one in my car atm it's making 410kw on 98 and has 260k on it though so might be in the market for one if and when it gives up. Would be good to know how much I need to save.

@stevecvntniko8271 7 ай бұрын

I got quoted 10k not including valve springs and head studs cause my motor already had them

@stevecvntniko8271 7 ай бұрын

The quote wasn't from this guy it was from empire Sydney

@CAIDMASTEROFPYRO 7 ай бұрын

@@stevecvntniko8271 Yeah I've also got valve springs headstuds and pump gears, would just need bottom end stuff

@stevecvntniko8271 7 ай бұрын

@CAIDMASTEROFPYRO spewing but I'll let you know in the next few days my car just blew up 1h ago lol so going full built bottom end with another place. I'll let you know what they say for price

@CAIDMASTEROFPYRO 7 ай бұрын

@@stevecvntniko8271 That's rough as man, my mates blew up about a month ago, he put in some big cams and the VCT gave up after about 10mins, every intake valve bent dented every piston.. He already had atomic pistons, rods, girdle etc. ready to go, and I found a block on fb marketplace that had already been machined for 20thou over pistons and was ready to go. engines just about done and ready to go back in the car. all up he's in it about 5k but that's very much because of the lucky block find $600 for a fully machined ready to go block