How To Replace Rear Trailing Arm Bushing 2012-2020 Ford Focus

Рет қаралды 58,509

2 жыл бұрын

Buy Now!
New Trailing Arm Bushing from 1AAuto.com 1aau.to/ia/MGSMX00040
This video shows you how to replace the rear trailing arm bushing on your 2012-2020 Ford Focus. Rear trailing arm bushings cushion the movement of the suspension and hold the wheel in the correct position. Clunking sounds or a shimmying feeling while driving can indicate that your rear trailing arm bushings require replacement.
This process should be similar on the following vehicles:
2012 Ford Focus
2013 Ford Focus
2014 Ford Focus
2015 Ford Focus
2016 Ford Focus
2017 Ford Focus
2018 Ford Focus
Tools you will need:
• Pry Bar 1aau.to/oa/1AXAA00020
• 10mm Socket 1aau.to/ob/1AXAA00017
• 15mm Socket 1aau.to/oa/1AXAA00015
• 19mm Socket 1aau.to/oa/1AXAA00043
• 8mm Socket 1aau.to/ob/1AXAA00017
• Ball Joint Press
• Cutoff Wheel 1aau.to/oa/1AXAA00254
• Trim Tool Set 1aau.to/oa/1AXXX00004
• Air Chisel 1aau.to/oa/1AXAA00270
• Socket Driver
• Socket Extensions 1aau.to/oa/1AXAA00015
• Torque Wrench 1aau.to/oa/1AXAA00044
• Brake Parts Cleaner
• Sandpaper
• Floor Jack 1aau.to/oa/1AXAA00068
• Hammer 1aau.to/oa/1AXAA00091
• Wire Brush 1aau.to/oa/1AXAA00079
Subscribe: / @trq
Check out our playlist:
Ford Focus 2012-2020 3rd Generation: • Ford Focus 2012-2020 3...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 15

@TRQ 2 жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@jamesturnure9735 Ай бұрын

Very helpful! I would suggest marking the orientation of the bushing prior to removal and then align the new bushing accordingly prior to installation. That will ensure that the 2 mounting 'ears' are parallel to frame when installing the bolts. I noticed that in this video, the ears were perhaps 30 degrees off from prarallel and this will preload and stress the rubber of the new bushings.

@richsmith9063 5 ай бұрын

Whew ..... that was a lot of work. Thanks for explaining all of those fine important details (about different choices to get things done)

@SM_zzz 2 жыл бұрын

Absolutely amazing work. I trained as an aircraft mechanic but dabble in d.i.y car stuff. Currently working on my sister's car and needed tips for removing the bushing. Videos like this make me very happy on so many levels, miles above other ones I've seen...so...thank you very much! Greetings from Ireland 👌🏻

@lonetraveler5660 2 жыл бұрын

Are your procedures working for Volvo cars as well?

@LI3TOM3 5 ай бұрын

now that looked a lot of work ,quicker replacing the arms

@omarkh1747 8 ай бұрын

Well done

@mannysautomotiverepair 2 жыл бұрын

Can this procedure be done on an 06 focus? The bushings look the same.

@liamscott3549 2 жыл бұрын

Yes, same set up at the rear

@cognac8297 11 ай бұрын

I bought two of these trailing arms for $350 a piece oem. I quickly found out by the alignment shop after leaving cause he said the rear toe adjuster was maxed out at +32 not even on chart. Then he signaled his friend that workes there ,he recommended loosing the trailing arm bushing bolts that worked alot it then went to +17 . im looking for +10 , we didn't finish cause we didnt know at the time i stayed thinking about it. For five more hours there is more to it than just installing it. Same goes for the front struts. After thinking about it. I still need to go under the car unloosen the rear trailing arm bushing bolts and on the trailing arm bracket holes actually side left to right 👍. So when i installed them the first time i didnt slid anything. For the back left standing behind the car left . I Need to loosen the bolts again and pull it out to the left then tighten it. And fir the right side pull it out to the right after you lossen the bolts and it will slide on the bushing bolt hole backets al in the air with a jack and pull it by and or by bar . The front strut when the bolts loose are pull the stuts up or down. What ever way the alignment readings say you needed. For caster.. . All i can say is nobody actually does or shows this job right. Cause tou will be thinking crazy someone saying your new stuff wont line up toe on car. Had me thinking for ever.. the rest of my full suspension is from trq. And for 06 civic coupe. The mounting point on the traiking arm the bushing where the bolts go on the civic are wide not circle. Give room for alignment . And for the front some caster. Probably the .4 everyone is missing in caster.

@thestig1899 Жыл бұрын

How do you know if they are bad?

@MPA9 Жыл бұрын

try to move with hand or with leg from the back to the front! just step your leg on wheel and press it, if u hear some noises then is bad.. or take off the wheel and move it, check the cracks..

@thestig1899 Жыл бұрын

I looked, they were toasted. Replaced both side’s

@jonathangaliano2617 Жыл бұрын

@@thestig1899 Need to do the same to my Mazda5 which is the exact same setup. Did you replace only the bushings or the entire trailing arms? Sucks how much of a pain it is just to replace bushings. I was thinking about going that route but I'd have to take the entire arm completely off and take it somewhere to press in the bushing. Maybe if it wasn't going into winter here I could do it on the street but I can't take on that kind of project knowing I have to have my car back on the ground that day. Also did you do the work yourself and it not how much did it cost roughly?