Worcester Bosch fan change

Рет қаралды 18,182

Күн бұрын

DISCLAIMER:
This video is only intended for use by qualified Gas Safe Registered engineers. You must not attempt any work on your boiler if you are not qualified. You must always carry out 26.9 checks upon completion of works on a boiler.
~
Whenever you change a fan on a Worcester, 3 things you must also have with you in case they need changing as well:
1) Electrodes
2) Bearing plate
3) Gas pipe tube
You won't be able to inspect these until you start taking it apart, and most of the time the electrodes will need changing, the bearing plate on the fan can split and so can the gas pipe tube.

Пікірлер: 27

@alfiespencer1161 Жыл бұрын

Mate your videos are unreal, so in depth and always help me out

@cputilitysolutions Жыл бұрын

Cheers mate, hold tight!!

@gasfitter78 3 жыл бұрын

I find leaving the clip in and just undo the nut on the gas valve is a lot easier to get the gas connection out.

@cputilitysolutions 3 жыл бұрын

Ah nice one I'll try this next time!

@suheilhanna873 Жыл бұрын

You saved my time today again 🎉, big thanks 😊

@cputilitysolutions Жыл бұрын

Top man!

@vahidkaregar8049 3 жыл бұрын

Brilliant video, thanks

@mohammednazir8307 2 жыл бұрын

Brilliant video keep up the good work

@simonmander4314 2 жыл бұрын

Great vid!

@jamesd755 7 ай бұрын

Doing my first one of these tomorrow. I've done some burner seals on these and found there's no one way to get that fan arm in.. with relative ease! Sometimes it's went in with the locking nut screwed mostly down. Other times it's only went in with the locking nut screwed away up. Absolutely hate Worcester lol!!

@cputilitysolutions 7 ай бұрын

Good luck man! 👊🏾

@jamesd755 7 ай бұрын

@@cputilitysolutions Thanks!

@Carl-re6zb 2 жыл бұрын

Nice vid bro...👍🏾

@davebayliss3142 3 жыл бұрын

👏👏👏brilliant

@kamaldahal4672 Жыл бұрын

Well explained

@MiAmigoArreglaCalderas 2 жыл бұрын

Gracias,

@mohammednazir8307 2 жыл бұрын

Could you make videos on how to put boilers into service mode/chimney sweep mode

@benscoey9675 2 жыл бұрын

That rectification probe can be awkward. I find it easier to get that and electrode leads off once the fan etc is out 👍

@SD-Plumbing-Heating 3 жыл бұрын

Good video, but turn your camera around, it's like looking through a letterbox.👍🏾

@cputilitysolutions 3 жыл бұрын

Thanks mate, yeah some of the older videos were filmed for my Instagram page before i started KZfaq hence why they're in portrait, new content will all be landscape going forward 👌🏽

@jamesd755 7 ай бұрын

As it was, had no trouble with the fan arm going back in, but that black plastic nut on top of the gas valve just typifies Worcester 🤢

@cputilitysolutions 7 ай бұрын

Ah yeah that can be a pain in the backside too

@stevenjohnson6082 2 жыл бұрын

check the flap do you mean the bearing plate

@cputilitysolutions 2 жыл бұрын

Yup that's the one

@curryhouse1377 2 жыл бұрын

How much a new original fan cost ?

@peterfarwell1732 2 жыл бұрын

I paid £150.

@jamesgrant5689 Жыл бұрын

Just been looking at your video and came across a comment made by yourself with reference to the "bearing plate" being faulty and making vibration noises. My boiler is making loud vibration noises along with the sound of dripping water, I've filmed it in the next couple of videos, kzfaq.info/get/bejne/g8eBhtmkucivkok.html, kzfaq.info/get/bejne/eNanicpkmNjbeXU.html. Would that be the bearing plate that is faulty and causing the noise, or could it be the fan?