2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
Пікірлер
@jeffreypence-yt6vq 2 күн бұрын
You know your stuff! Helpful!
@jplbbs 12 күн бұрын
Awesome video! Saved 250 from dealership
@RESTLESSOFFICIAL 15 күн бұрын
Would this fit a G body 1984 buick regal ?
@likablemichael 15 күн бұрын
Not sure on that one, check out their website and try to see where the crossmember sits in relation to the engine 🤔
@serafsup99 15 күн бұрын
Oh I see! My bad! Pressed fittings are nightmare! But it’s still funny as shit watching you guys trying to pry out that fitting!
@serafsup99 22 күн бұрын
Righty tighty lefty loosely! Lol
@likablemichael 16 күн бұрын
What are you referring to? It was a pressed in fitting, not threaded 🤷♂️. Otherwise, it would have come out easy but good suggestion 👍
@MustangBullitt-sz8tg Ай бұрын
Well, ive done this on a dodge Durango before, by myself, guess its time to start on the 5.3 trailblazer that spun a rod bearing. about to tackle this thing. Im probably gonna need to get that clutch fan tool along with the fuel line disconnect tool. Very informative video, i will sub to your channel, keep the challenges coming 👍
@henrychristen7336 Ай бұрын
I got the same car and plan on doing an ls swap, should I strip everything from the engine bay or leave the break lines?
@LongboardBail Ай бұрын
Appreciate the video I’m looking to probably swap my engines. I got 550,000km on my daily & have a parts truck with a blown trans with 200,000km. How long did this take you to remove it?
@likablemichael 29 күн бұрын
A few days because I could only work on it a few hours at a time
@N4GUZZ Ай бұрын
My question is it how much hp until it blows up? Because I've heard of the nv3500 but i don't know anything about s10 transmission.
@toolwithintention Ай бұрын
Throw that fitting in a freezer next time
@benvin10365 Ай бұрын
Can you link the throttle cable kit in the description?
@likablemichael Ай бұрын
Done. Let me know if you don't see it in there
@benvin10365 Ай бұрын
@@likablemichael I see the link. Thank you!
@benvin10365 Ай бұрын
@@likablemichael I need to go 8 to 10 feet for my engine swap.
@benvin10365 Ай бұрын
@@likablemichael do you know of a way for me to get the cable threaded ends, the sheathing, and the cable separately so that I can go 8' - 10' and terminate the ends where I need them?
@andrewsharp2418 Ай бұрын
Well earned subscriber and a like for you good sir.
@gabrielthentural480 2 ай бұрын
Man you showed some pretty slick techniques too ,that bolt removal was sick ,I would frame it lol good stuff
@Eastsiderep40 2 ай бұрын
You a bad mufucka! I’m watching this video discouraged as hell like damn that’s a lot of work lol I have an engine I want to remove from a 2003 GMC Sierra 1500HD that I wanna rebuild. Mechanic said 2 of the cylinders are scoring but I wanna get a second opinion before I make my move.
@likablemichael 2 ай бұрын
Good luck my guy!!!! 🤞
@user-mp3we6ti5x 2 ай бұрын
I need them cats
@jasonrivas8029 3 ай бұрын
hey man do you happen to have the link for the parts?
@likablemichael 2 ай бұрын
I have it for the throttle cable and it should work with most throttle bodies (LS cable driven) www.ebay.com/itm/373536944130?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=0IEu4QEtTyG&sssrc=4429486&ssuid=gekgCJySTfS&var=&widget_ver=artemis&media=WHATS_APP
@jasonrivas8029 2 ай бұрын
@@likablemichael thanks brother appreciate it !! 👍
@JohnWick-wm4pd 3 ай бұрын
Beautiful car!
@dustinbingman382 4 ай бұрын
Did you just let the tranny drop?
@dako9307 4 ай бұрын
My #1 hangup on my project has been the fucking powersterring bracket. There's like a bunch of shit connected to it, no way for me to remove it, because the solid lines keep in place. Fuckig. Dumb as shit.
@dylanjimenez1952 4 ай бұрын
Great video
@joshryals96 4 ай бұрын
I caught a Chevy on fire with a top post battery once
@jalenswrld 5 ай бұрын
did you have to disconnect control arms?
@likablemichael 5 ай бұрын
No, I don't believe you have to on the fronts
@shory143 5 ай бұрын
Monkies fucking a football
@HeavyLS 5 ай бұрын
Where did you get your numbers for .125”-.2”? Is that spec for all NV3500s?
@likablemichael 5 ай бұрын
The clutch shim kit called for that tolerance
@user-in5hj3cz8q 6 ай бұрын
What’s the part number?
@darthinsidious1769 7 ай бұрын
What size bolts connect the engine mounts to the frame mounts?
@marlonsanchez4214 7 ай бұрын
Congratulations on the house
@ChristianHernandez-vm2fk 8 ай бұрын
Is that 1/4in plate ??
@likablemichael 7 ай бұрын
It's 1/2" which is overkill. 1/4" would probably work but I would go with 3/8" if I were to build it again.
@damag3plan 8 ай бұрын
Such a practical way to experience magic of Carmen
@Airman.. 10 ай бұрын
A blow torch would of made this job like a breeze
@likablemichael 10 ай бұрын
We actually tried that and it still wouldn't release the neck 🤷♂️ I stopped because I was concerned we were going to melt the aluminum or compromise the integrity of the piece 🙃
@BritaneeOswskey-sw3bn 10 ай бұрын
2 years late but the only things you didn’t show are the exhaust manifold bolts and the motor mounts correct?
@likablemichael 10 ай бұрын
Correct, I had to cut the exhaust out because the bolts were rusted on and rounded. The motor mounts were two nuts on the backside of the mounting location.
@BritaneeOswskey-sw3bn 10 ай бұрын
@@likablemichael Awesome thank you!
@frymus1c 10 ай бұрын
Use a hammer and a chisel for the oil filter
@zdd22fixes47 11 ай бұрын
Oh my!...
@wizzer03 11 ай бұрын
They make that intake in a low profile that will help with hood clearance. I ran into that same issue with my LS1 GTO when using that manifold.
@likablemichael 11 ай бұрын
Might just have to swap it out to try and keep the hood intact 🤷♂️ Thanks for the insight 👍
@GuitarKAB 11 ай бұрын
Congrats on the 1k sub bro
@likablemichael 11 ай бұрын
Thanks bro!! YEEWW 🤙
@Leonidas_Apollo 11 ай бұрын
YOOOOOO I'M THE THOUSANDTH SUBSCRIBER CONGRATS DUDE 😭😭
@likablemichael 11 ай бұрын
I saw that bro!!!! Thank you good sir 🙏 YEEEEEWWWW!!! 🤙
@etet4736 Жыл бұрын
Do all RC 350 F SPORT models come with the medal filter housing? Ordering parts and jack, so I haven't checked mine.
@likablemichael Жыл бұрын
That's a good question 🤔 I'm not entirely sure
@longlivechina7538 Жыл бұрын
Your my hero
@dreebradley1306 Жыл бұрын
Glad to see you back man lmk if you need any welding done
@likablemichael Жыл бұрын
Will do big dawg!! Hope you're doing well 🤙
@zachblack5917 Жыл бұрын
Broooooo helll ya he back!!
@likablemichael Жыл бұрын
🙏
@DavidSchwartzjr Жыл бұрын
Good to see you back with an update bro! Congrats on the new house and promotion at work! Time flies, but definitely keep doing you! Almost at 1K, hell yeah! 😎👍
@likablemichael Жыл бұрын
Thanks big dawg!! Hope all is well in your neck of the woods 🤙Need to get over to your channel and see what new swanky watches you've been rocking ⌚️
@DavidSchwartzjr Жыл бұрын
@@likablemichael haha it’s gotten outta control my man!! 😅
@austinrussell5577 Жыл бұрын
I would definitely relocate the coil packs to the firewall or fenders.
@likablemichael Жыл бұрын
I'll look into relocating those guys and getting some longer plug wires 👍 thanks for the recommendation!
@Djm9393 Жыл бұрын
Full sending never lifting 😏🤙mobbin deep 🙌 love the vibes great too see you back bro keep doing your thing congratulations on your promotion 👏
@likablemichael Жыл бұрын
Thank you sir! Hope you're doing well 👌
@murdamob Жыл бұрын
Nice will like to see how the project it’s doing now
@likablemichael Жыл бұрын
Hopefully I can find time to get an update video out soon
@ILOVEYOUHALFISH Жыл бұрын
Rip hand
@CarlosRamirez-dq3cp Жыл бұрын
Did you ever continue?
@murdamob Жыл бұрын
Right
@likablemichael Жыл бұрын
Unfortunately, I have not. I'm trying to make time for an update video 🤞
@RandDCustoms2 Жыл бұрын
Did your injectors fit with this manifold or did you change them to the LM7 longer injectors?
@likablemichael Жыл бұрын
Unfortunately, I have not had time to continue 😕 Shooting to have an update video soon.
@aydenjerutis2780 Жыл бұрын
Will this throw out bearing work with a manual T-56 trans ?
@likablemichael Жыл бұрын
You'll have check the specs but I believe it should 🤷♂️
@julio_soloartist2155 Жыл бұрын
Hello my name is julio I have an LS 4.8 and I have a NV 1500 transmission I’m trying to see how I can go about this. Do I basically have to get the same thing that you have to make it work?
@likablemichael Жыл бұрын
The most important part of all this is that the transmission bolt holes align with the LS bolt holes on the block. Some NV1500 and NV3500 are correct, some are not.
@LooseFab Жыл бұрын
just about to start this swap on my 280z, this is some great inspiration!
@likablemichael Жыл бұрын
Nice 👌! Check out Apex Engineering, they have a lot of parts I wish I knew about before I started. Best of luck 👍 yeeewww!!