Thank you! Exactly what I needed! I put glass soda bottles in the freezer and they exploded because I forgot them in there! 😅 so I really needed to clean under the bins and all around the freezer.

Doing warranty work for a high rise. They had about 150 of them. Other than a few belts no early sealed system failures while under warranty (as it should be). But most the time it would just be customer dissatisfaction due to dry times

Nice!

I believe your Fluke 177 has a lowZ option to measure voltage under a small load. Was the problem in this case inside the appliance or in a wrongly installed wall outlet?

Whirlpool dishwasher venting problems

Very gald I came across your video. I believe I found the source for my LE error code. On the very bottom of the wirring harness where it splits and goes into two connections and under the washer. The baby blue wire is broken, and the black wire next to it is chaffing. How would be the best way about going to repair this? Space is limited. Flip dishwasher over to see if I can gain access to wiring harness?

So when you jump the yellow wire it's just like you're running the fan with a full duty cycle?

What does it mean when you have a GE monogram and the temo control panel beeps 3 times when you touch it?

How did you wire up the replacement condenser fan motor? I bought a similar one today and noticed that my fridge only has a blue, orange, and green wire. My new condenser fan motor did not come with instructions unfortunately.

The yellow wire is normally the speed signal coming from the fan, and this is also used to sense whether the fan is running or not.

Junk refrigerators

It never turns off?

How was that jumped? What was used to supply power?

Nicely done, problème is on some of devices, the paper schematic is nowhere to be found. Where to get the digital version that you're using ? 😊

WHERE CAN I BUY THAT DEVICE TO READ THE AIRFLOW?

I broke flapper what do I do

I broke the flapper what do I do

Thanks so much, that was a life saver...!!! 👍

I'd like to see a link to the PDF of that service manual that you were holding.

I have a Samsung it keeps restarting what could that be

How hard of limits are the resistance values on the sensor from 46K to 52K ohms? For instance, does a measurement of 55.3 K ohms indicate a bad sensor?

Thank You!!!

Thank you so much!!!! The tec who came told me to replace the mcu … 300 euros all i did was what you said… i messed with the wire harness on the mcu! Didnt cost nothing! You saved me tons!! God bless you!! Cheers from Greece❤

Thank you soooo much I could not figure out how to get this rack out. My freezer is all frosted up and frozen and I need to thaw it out and can't get the ice out which should not be there lol

Git er done!

You saved me some $. The noise filter was at 120v. The computer lite was not on when washer was plugged in. What a Hassel though. I just replaced the clutch bearing

Could that motor go out in the middle of a cycle?

I don't get it. It the heating element is working, how is it the jazz board?

Thank you so much! I was going through some of my girlfriend's late grandfather's tools (electronics repair man entire life) and I found an Eico 1140 Combination box and I couldn't understand the use of it, but now the general idea makes sense. I know a little different tool but very useful! Great video, nice and to the point. I was an appliance repair man for Sears in a previous life and wish I knew about substitution boxes 🤦.

YES! Thanks so much. This was my question and you answered it clearly and to the point. Perfect!

Very nice short cut , I used to do this on the condenser fan motor on the AC and by pas it to see if the board is bad or if the motor is bad . thank you , Question are you the instructor in Samurai website ?

so are lower numbers mean colder, higher number mean warmer? mine is stuck on 7 / 4 right now. Refrigerator is not cooling, freezer must be full of frost/ice because I can't get the door open. Pulled hard and the handle came off on one side! S o need to try to make freezer warmer if I can get the control panel to change - just don't know whether to go up or down to make it warmer

Im a little late but just came across your site. My issue is the wire is green not white so do i keep it on the case and just add new ground? Im changing from 3 to4 wire. Thanks

Hello Samurai Great Video I have a very similar whirlpool dishwasher that only heats for 2 cycles after using diagnostic mode ? I have replaced the PCB in the door and the TURBIDITY SENSOR same thing still happening? Any ideas?

If it's a 2 phase compressor, what do you think about tying it into the power to the compressor? That way, the fan only comes on the compressor turns on.

Very good video. Been there done that, as the saying goes. Also have done that on a few older Whirlpool under counter ice makers for same failure.

One of the best units ever made that model 👍

Great video there is a place in Illinois called corecentric that rebuilds that board there is also a kit if you call kitchen aid maybe they will provide part number only factory service has access👍

Thank you for saving my freezer from my wrath! Bad enough that my idiot of a roommate blew up a can in there. Then I couldn't get the rack out! 🤬 You're a lifesaver, brother! Thank you!

You are the best bro

Do you use a service to obtain your schematics for the different appliances or do pull them up from the manufacturer site on a case by case basis?

So the company I work for has one of these specific testers, however it’s showing its age and I offered to build/prototype a new style of one. Do you think that it’s a worthwhile venture to do so at least past my company’s level, like market it. Same testing concept but just a different package.

Thank you so much your video diagnosed everything wrong with my dryer.

they use resistance for liability you do not have the power on so you can't get hurt

I really like this guy attitude. We need more of you!!!

Is it common for the inverter board to go multiple times or would there be an underlying issue? Customer had their inverter board replaced in December. It's June and they're having the same problem. I changed the condenser fan, I've checked the DC and AC voltage, resistance on the compressor is consistent across all leads... Could it be the inverter again? Or possibly a surge issue that's taking out the inverter? I'm lost.

My bosch she65t55uc/02 dishwasher wont release the soap pod during the cycle. I changed out the soap/rinse aid dispenser thinking it was the solenoid maybe went bad. However the new one does not work either. I was told that I need to run a diagnostics test to determine which part is the issue. How would I go about running a diagnostics test on my dishwasher?

Thanks so muc helped me

Maybe he was referring to the rating plate on the appliance.