I have an older Hot Springs Jetsetter that I'm converting to 220/240v. I have the new wiring in place but do I need to change the dip switch settings? The wiring to the terminal block looks to be from the breaker to go to black wire to #2 white wire to #5 and ground to ground bar. Where does the red wire go? Is there any white wire to remove as you've shown on the balboa?

This is a great video - very complete and saved me a lot of time and money … thanks for posting it! Keep up the great work

hello, I am in France and owner of a j335 jacuzzi from 2015. I have an FL1 code. the massage pumps work but the circulation pump does not. the fuses are ok. Should the circulation pump be replaced? thanking you for your help.

Thanks so much for making this video. We were able to change out the heater and are now back in business!!

I have a circuit board that I'm unable to identify can you help me ?

Nice video

Remember when this guy got sued lmao 😂 spa man got spa slammed

Can you use a jacuzzi pak to wire.

Hey Spa man can you show what color wires go where in the sub panel breaker please

Great video. My hot tub breaker trips intermittently. Stays on for hours then when we go to use the breaker is tripped. Any Ideas?

Great vid! Does this work on a hot tub with Two pumps?

You are very good at what you do but why do you call a neutral a coman and a disconnect a sub panel?

Hey Scott, what is the black box behind the pack? It's leaking on me.. is it my circulating pump?? Please help!!

Thanks buddy.That nearly broke my balls trying to figure it out.

How and what kind of material do you use to re-form the big big hole? Thanks.

Just curios, why don't you use the silicone caulking instead of PVC?

What about the hole drilled in hot tub to run conduit? Did you seal it with grommet or something?

Can anyone help? I need to replace the control board on my spa. It's a Leisure Bay G2 plus super duplex. 2 pump spa. The board S/N is 52326. The chip number is G2R1B. This board is not in production anymore. Can someone help me find a replacement that will work??? Please

Excellent video! Thanks!

Nice i like

Hey Spa what does the other end of the power cord

Fantastic video - thank you.

thanks. Video could do with some speeded up sections.

spa man. question I have the exact Gecko controller and its tripping my 50a breaker. I've disconnected the pumps, heater and it still trips. I checked both incoming wires Red/Black and both read 121V. If all devices are unhooked from the controller and it still trip? Does it mean the controller is bad?

would a 6 inch flex hose be long enough to heat up get a coupler in between?? I currently have a rubber boot with clamps in between two hard pipes. Not sure if it will hold

What about motor for pump doesn’t it need to be rewired too?

Thanks so much for sharing your knowlwedge, video worked a treat- all the best from the UK 👏👏

I really like these videos,but I wish there is a place to ask questions about my old (2002) Vita hot tub. It was given to me and I don't know anything about it. High limit code

Does this work if only one section isn't working?! Can't seem to figure it out

Who went in your tub lol

I wish there was a better aftermarket heater - it is such a lousy design and not a good quality part. I just replaced mine with a supposedly OEM one and one of the temp sensors that came in it was DOA and out of spec so it would throw a temperature probe error. I was able to use the ones from the bad heater which worked. Now a few months later the new heater is tripping the GFCI again. That electrical connection on the heater is such a bad design too. I had to grind down a wrench to hold the stud because you have so little room. Guess I'll buy another one and hope it is a better unit.

you can pump chlorine hot tub into a salt water pool without issues, just not the other way

Why does it heat so slow about 1 degrees a day

Thank you, Scott! I'm actually having to assess a Marquis hot tub (Balboa power pack) tomorrow because the owner says it keeps tripping and you break it down perfectly! Mahalo! 😎🤙🏽

What’s that piece you’re replacing called ?

Great info, with things to look out for in the future. I live in Nevada and my Balboa breaker trips only qhen its hot outside( 100+°). Replaced wire to appropriate size and solid ground. Still pops when ambient temps are high. Maybe the heater is my problem.

We just did something like this. Glad to see that there is no damage. Got to stay on our toes.

What does this cost? I want a hottub and massive smoker in my backyard but there is limited access.

***Question***Right off the bat I think you helped me! Last spring my hot tub tripped a couple times after I had everything clean and prepped after the winter. I also noticed the water level slowly going down. Instead of figuring it out, I just shut it down (busy times). Now, a year later I need it back up and running. Last week I opened the panels and turned the breaker on. I instantly noticed water spraying from the bolts on the heater. The breaker quickly tripped. Now it doesn’t come in at all. Your video showed me that I have a heater problem. My question is, because my system doesn’t do anything at all now, should I replace all the components in the box, or should I just replace the heater and fuses? Appreciate anything you can offer!!

How did/do you seal up where the flexible conduit goes through the cabinet to keep out the critters? Silicone, Duct Seal, or any special grommets? Thanks in advance!

do you have a video on how to remove that spcific model of pump and control panel for repair? can't find a "how to " anywhere

@SPA MAN do you have a video on how to remove that spcific model of pump and control panel for repair? can't find a "how to " anywhere

Worked perfectly

Thank you for this fine video! I have a Boca Grande 10000 I believe from 2005. The entire cabinet and frame rotted out and animals ate some wires and hoses. The bottom is also rotted out. I want to attempt to fix it. I will build a new frame, although I'm not sure how to tackle the bottom yet, but I'll come up with something. There is a kit to create a new cabinet, but it requires a sturdy frame. I feel it will be considerably cheaper than a new ones and everything else is fine. What are your professional thoughts on taking this on? Is it worth it? Or is it a tail chaser.

How would i wire the main breaker if the ground and neutral go to the same bar?

Wouldn't an angle grinder or circular saw be a whole lot quicker?

I've tested all of these circuits. Even when I have them all disconnected, the breaker reliably trips after 1 min 17 sec. I have no warnings on the panel before it happens. It's a Jacuzzi 300. Any thoughts on what to try next?

I shorted it with a screwdriver but exact same behaviour, pump starts for 2-3 secs (almost the time it takes for the flow switch to connect, then stop. I really thought it was the flow switch and before ordering i tried to jumped it but it's the same behaviour, pump will do the exact same 3 seconds start and stop. Do you suggest to try with a new switch and sensor heat anyway? or go for a new pump? or cardboard? please note last year my cable melt in the cardboard. A technician just shortened them and reinstall them, they didn't melt so far but maybe the cardbord is dead? any idea? Thank you :)

Just watched the video on the tub not heating up. I have a small TX Hot spot. My tub is heating but as soon as I press for SYSON for a schedule run it shows a double spaced lines and stops heating. I'm almost sure it's the pressure relief switch. Before I spend $60 could it be anything else.

Can i run a 5.5kw heater in a pack that came with a 4k?