Пікірлер
@flashg1160 Күн бұрын
Since it is a press fit how did you get the bearings out? I have some water in the oil so I bought the oil seals. Is it possible to get the seals out of the cylinders without pulling the crank and rods out?
@davidlang7271 3 күн бұрын
After spider is replaced and the pump coupler is moved up to the motor coupler, it looks like they butt up to each other. Is there suppose to be a small gap (.02) between the two ? Any negative repercussions either way ? I'm going to try this and if there is a way to screw it up, I'll find it.
@mcodrington1487 Ай бұрын
The section above the 2 capacitors and the number 470 on my board is dark like its burnt so im guessing i have to order the entire board but the tv still looks brand new.
@davidhansen8396 Ай бұрын
I have an annovi rcv3g27 that was working fine. Now I pull the trigger and the motor dies. If pressure is turned down it works fine. Any suggestions
@RandyGriffin-jx7uy Ай бұрын
This is a great video. I know it’s over a year old but it is great . I’ve sense built three of these they are really easy to do and the seal kits are cheap. Thank you sir for the great work gave you a sub . Be safe brother
@SABsGarage Ай бұрын
Cool, thanks!
@davidswitzer8994 Ай бұрын
I have a 1973 Harleydavidson golf cart
@DK-vx1zc Ай бұрын
nice job!
@johnkick7904 Ай бұрын
Nice safety gear😂
@ianfiddes9871 Ай бұрын
Nicely done 👍
@rogerwilliams2902 Ай бұрын
Cracking job!. How refreshing it is to hear dimensions in inches and weight in pounds and ounces instead of all this metric rubbish like here in the UK. Just subscribed .
@unclebilly4696 Ай бұрын
The alignment pin was a brilliant idea. Great work as usual.
@BoostedMonkey4g63 Ай бұрын
Nice tray, I have the same exact band saw. What model number is yours? Mine has no information on it. Thanks.
@a2outside Ай бұрын
Great series! Didn't notice any movement / rattling coming from your brake assembly - just purchased a Harley cart built in 1975 and I can jiggle the brake assembly, though the brakes still work. Looks like I just need to tighten things up. Did you happen to take any videos of reassembling the brake?
@chrissmith7669 Ай бұрын
Lol. I’m the kind of guy who wants a three wheel Harley golf cart so I can tell people I ride a Harley trike. lol lol
@MitchellMartinez-rx9ej 2 ай бұрын
This is a very helpful video and the man behind the video is very knowledgeable and explains the how to great. Thanks Mr.
@dillardwinters4882 2 ай бұрын
I need a are filter too . How to know what filter get
@dillardwinters4882 2 ай бұрын
I ordered a fuel line that was to big so I had to fabricate my own
@dillardwinters4882 2 ай бұрын
Picked a026 2 weeks ago got it running good
@RustyInventions-wz6ir 2 ай бұрын
Just found your channel and subscribed. Nice work. Good looking shaper
@josechavez656 2 ай бұрын
Best one yet.
@ivanuribe2819 2 ай бұрын
Wow, that's easier than I thought. My suspension has gone bad in my '08 Colorado, Im planning on buying some bilstein shocks for the front and rear end.
@KRAMPUS_G60_16V 2 ай бұрын
Great and informative video. All of them have straight head screw on the handle. Too bad it's not a pro version with little extra power, but still I bet you fell in love with her.
@Tom-ic7hw 2 ай бұрын
if you could mass produce those I bet there are alot of saw owners like myself who would buy one I use a mister nozzle and it works but not as good as flood one thing I did was cut a pice of 2x4 wood sawed a kerf in it deeper than the saw blade and just let ride on the blade up at the front guide it wicks some of the chips and coolant off before it goes to the front drive wheel I guess u cold put it in a bracket with a clamp to adjust the pressure it puts on the blade it does wear little
@georgened 2 ай бұрын
🥱💤💤💤😴
@joemanuel07 3 ай бұрын
Nice job sir thanks for the video I'm about to do that on my 2006 canyon .
@Displays.1234. 3 ай бұрын
Definitely the red cap is only a shipping cap, it needs a vented cap fitted, because it will pressurise the case if not. Seen lots of videos on these pumps... Great video explains a lot...
@darkshadowsx5949 3 ай бұрын
how hard would it be to do it on a low profile tire?
@pzindy 3 ай бұрын
I have always just kept the guards on and drive the front wheels over the mower deck. Easier than dragging that heavy deck out the side IMO.
@traviscichocki3536 3 ай бұрын
Why would you think my harley cart would be going just fine in reverse, but will not engage forward until WOT
@stevew2605 3 ай бұрын
AWESOME video! I 'm just getting ready to rebuild the primary clutch on my 72 Harley 3 wheel cart... Straight forward explanation, right down to refilling the lube. .. VERY HELPFUL! ... A+
@bostongeorge1000 3 ай бұрын
Can i contact you. I have a 74 and my clutch doesnt look like yours and i cant figure out how yo get it off
@excalibull4984 3 ай бұрын
Great work! My recently inherited 16-G is barely moving forward and this is exactly what I was looking for. Now just waiting on the part to arrive!
@longsleevethong1457 3 ай бұрын
Can you replace the tpms with a regular valve stem? I have newer wheels on an older car.
@summerforever6736 4 ай бұрын
Good info ! You can use a clamp to hold the tire squized while you change sensors out no?
@SABsGarage 4 ай бұрын
Yes you can, and I should have mentioned that.
@longsleevethong1457 3 ай бұрын
@@SABsGarage Can you replace the tpms with a regular valve stem? I have newer wheels on an older car.
@SABsGarage 3 ай бұрын
@@longsleevethong1457 Absolutely, but you get the notification on the dash if the vehicle doesn't see the sensors.
@JOESMITH-bx8qv 4 ай бұрын
What keeps the rain out? Here in Florida it rains sideways a lot during storms.
@SABsGarage 4 ай бұрын
In extremally heavy rains it will keep the majority of the rain out but not all. The rain hits the louvers and drips on a drip edge preventing most of the rain from going inside. Also the pipe inside is about half way up inside the spinner to help with rain. I've only had a few times rain got in and was only a drip or two.
@521farmer 4 ай бұрын
Howdie Ya Make it look easy they look like they do the Job what Kind of steel to use on something like this ? cause wood not have a Clue and ya did not sell the Shop to make these so ya the Man Thanks again for showin us How it,s done carry on ya got this from Canada SK were it gets pretty chilly Here Minus 33 yesterday and that wind !!!! Brrr Owell no shop time for awhile gots lots to build and make for Kids this year so till later Keep it up Sir
@SABsGarage 4 ай бұрын
If i was making them for a shop that would be used every day, I'd probably use 4140 or something that is hard and wear resistant. For this I just used what I had lying around, so was probably 1018 cold rolled. Thanks for watching.
@521farmer 4 ай бұрын
Howdie Glad ya shared your Project with us signed up so can see more of this it looks easy enough ya don't have to be a Rocket Scientist to make what ya doin so Thks again from Canada SK Mighty Fine Sir it looks like it will work out
@TheStanford01 4 ай бұрын
A great help. Many thanks for the information.
@jkahnsculptor 4 ай бұрын
Thanks, mine just went south, now I at least feel confident to give it a try
@cdnglenwood2234 5 ай бұрын
Thank you, exactly the video I was looking for 👍
@TulaneEddieIII 5 ай бұрын
Great video. I’m thinking about doing this. My issue is there is water mixing with the oil, turning it white. I am wondering what parts I should replace. Maybe the orings on the 6 valves? Maybe the 3 seals on the pistons? I see online this is a water seal kit and oil seal kit. I would appreciate any advice if you have the time. Thanks
@SABsGarage 5 ай бұрын
Thanks, The oil place for oil to get into the water area is the seals behind the piston. So I would look at the pistons and seals for replacement. I will say it can't hurt to replace all the seals while you are there though. Good luck!
@TulaneEddieIII 5 ай бұрын
Thank you
@ritaroy4248 5 ай бұрын
😌 "PromoSM"
@ConSeann3ry 5 ай бұрын
Appreciate the video!
@user-fz1dr6nk1u 5 ай бұрын
I have a problem with my pump
@jasonsellers1632 5 ай бұрын
Guaranteed that didn’t fix it! I could see once the toner ring was cleaned that it had missing chunks! Toner ring damaged and should have replaced the entire assembly with sensor installed already!
@Shagula420 6 ай бұрын
Was looking at my vise before I left thinking about a piece I have to do tomorrow about the same size. I was wondering if this would work. Now I know! Thanks dude!
@elminero49 6 ай бұрын
I just got the ken Tool duckbilled tire wedge hammer. These are a ton of methods for breaking the bead. I decided on the most simple, effective and least cost. I have to admit that I don't feel comfortable swinging this against a tire. I will most likely place it on the tire and hit it with a dead blow hammer.
@larryjacox2876 6 ай бұрын
Where did you get a print out of the instructions?
@SABsGarage 6 ай бұрын
Manuals, www.buggiesgonewild.com/columbia-parcars/
@ronbednarczyk2497 6 ай бұрын
Very helpful video. I just replaced the left front sensor on my son's 2005 GMC Canyon.
@76Starship 6 ай бұрын
Good video. Can you please add the tank & pump information (make, model, etc) to the video description? I want to do something like this on my saw, but I need to source a tank & pump first. Thanks.
@SABsGarage 6 ай бұрын
Someone gave me the tank and pump. The number on the pump is Jet HBS916W-CP, the tank is this one I think, Part Number: HVBS7MW-66N