I have an 04 Ram 1500 5.7 liter 4x4 with 214,000 miles and this fixed my transmission. It started to jerk forward when stopped at a light with the brakes applied for a couple of weeks. Then one day after leaving work, the engine light came on and the transmission felt like it was taking off in a higher gear than first gear and stayed in that gear without shifting all the way home. I hooked up my engine light scanner and got 3 codes, a generic P0700, P1775 and P0841. I couldn't find anyone else with those codes and a solution online but read other people's trucks that were getting a different code and would stay in 4th gear so, I decided to change the solenoid and it fixed the problem. The Mopar solenoid, new filter and 9 quarts of fluid it took to refill it cost me $230. Thank you for uploading this video!
@brym34522 жыл бұрын
Wow where did u get that deal on the Mopar brand at ???
@Leo-cb8jp5 жыл бұрын
Thanks to u I was able to do this by myself. I also replaced the transmission radiator and flushed the whole system to the last drop. Purchased everything from the dealership except the transmission oil. In the end of it all i added a little over 11 quarts of transmission oil. Truck is working beautifully. 2004 Dodge Ram 1500 5.7 Hemi 4x4 Laramie Edition 196,000 miles
@juancastro69345 жыл бұрын
I'm glad this worked for you.
@brandonsowders20865 жыл бұрын
What was your truck doing? I have a 05 ram 1500 5.7l that idles finns and cranks fine but wont go into any gear. Like it even grinds trying to go back into park I have to turn it off and put it In park and fully shut it off after.
@marcusjennings58384 жыл бұрын
@@juancastro6934 mine is doing the same what did you do
@juancastro69344 жыл бұрын
@@marcusjennings5838 Mine was not grinding or making noises. Any grinding or noise would most likely be a mechanical part problem and at that point I would look into a replacement transmission or rebuilt. Mine was having problems shifting and downshifting, but the fluid was always clean and had no metal shavings in the magnet inside the oil pan. Best of luck.
@davidm.10983 жыл бұрын
thats the cleanest 05 in 2017 i ever seen lol
@KingDevilCharger5 жыл бұрын
Thank you for this video sir!! Mine went out today and your video will be my guide to getting this done. I've worked on cars for many years and your video breaks it down perfectly.
@juancastro69345 жыл бұрын
Hope it help. Best of luck.
@saulvalquier2828 Жыл бұрын
@Juan Castro tengo un problema con mi ram 1500 2006 , cuando Pasa Las 50 millas , cuando quiero aselerar ase como un brinco o golpea , pero si boy abajo de Las 50 millas no tu cres que sea El transmission solenoid ?
@juancastro693411 ай бұрын
@@saulvalquier2828 Disculpa la respuesta tan tardada. Si teienes un Scanner de OBDII, examina si tienes codigo de la transmicion. Si no tienes Scanner, puedes ir al Auto Partes local y que ellos te lean el codigo. El selonoide tiene sus codigos cuando estan dañados. Buena suerte
@tallll705 жыл бұрын
I did same on 2006 model in 2017... It was $400 solenoid pack, screen, filter, 11 quarts of fluid. I got so lucky it stopped shifting 1st and 5th 5 hours away from my home. Next day i start and it all worked good the whole way home, 2 weeks later again, but in my city. I changed it then, if it's done soonest it happens, transmission remains undamaged. After fix, it was all great, super smooth shifting, no kicks in D selection, great Chrysler transmission at least for me
@Mike-cn1ei4 жыл бұрын
Thank you for this video. It saved me a great deal of frustration.
@FragoutDesign6 жыл бұрын
Thank you for posting this!!! mine just went out today....
@JoseHernandez-lm3hs3 жыл бұрын
Thank you brother I got one replaced today successfully thanks to your video.
@JAKWEES6 жыл бұрын
You're a life saver. Great video
@fosgate3754 жыл бұрын
Thanks for the video Juan. I have an 04 Ram 1500 with a 545rfe transmission in it. It recently started having an intermittent problem where it would not go into first gear when I come to a stop or shift into third when driving on the highway. More often than not, it works fine but when it doesn't, it feels like I am trying to take off in second gear. I can pull over (or wait until I hit a red light) and turn the engine off and then start it again, and it works fine. I've been thinking it was a shift solenoid but I've never changed one out before. This video just made life easier!
@juancastro69344 жыл бұрын
Well, hope that solves the problem. Please follow the instrctions and you shouldn't have any issues. Best of luck to you
@coreyhhughey93104 жыл бұрын
Hey glen I’m having the same issue. Did this fix your problem?
@juand.hernandez82832 жыл бұрын
It happens the same to mine, when i turn it on it works perfectly but when i come to a stop it starts having problems, i have to turn it off then on and then it works
@osirisnero8641 Жыл бұрын
I have exactly the same truck and tranny, but mine straight dies and I have to clear the code or it won't start back up
@gregy36604 жыл бұрын
i just wanted to say thank you for the video with out it i would not have known where to start
@mintone20083 жыл бұрын
Excellent video......straight to the point with no unnecessary bullcrap........thank you!
@roshoirelliott23502 жыл бұрын
Io
@roshoirelliott23502 жыл бұрын
Io
@rodneygillespie76709 ай бұрын
@@roshoirelliott2350j
@bogus3605 жыл бұрын
Great video for the DIY'er! I was getting an OBD (check engine light) code P0750 for "Solenoid A," with the tranny going into limp-mode. Although I could clear the code and make the trans work again, it would come back at some point (hours/days/months). I replaced the solenoid pack and both filters using this video as my "go-to"... especially for that damn plug at the 00:40 mark. Transmission is back in operation like normal. THANKS!! **NOTE** for others... Not only does that "cam-lock" arm (white plastic) have the typical little red lock, it also has another push-type latch at the top, directly behind and centered to the arm itself. This latch must be pushed toward the transmission housing to release the arm. At that point, the arm moves freely to release the whole plug. I hope that will help others from breaking anything. p.s. - Use a VERY large pan (think large turkey roasting pan) for draining. Mine drained about 6-1/2 quarts, and almost went over the top of my goofy aluminum pan I bought at the grocery store.
@dcsco3 жыл бұрын
Thanks for that NOTE on removing the white plastic arm lock on the connector. That was very helpful. I'm going to try cleaning the connector pins first to see if that fixes the error code, before replacing the solenoid pack. I'm hoping that it might just be a bad connection... BTW, I'm getting a P0700 and P2706 code on a 2005 Durango with the 5.7 Hemi engine.
@jeremywilson83342 жыл бұрын
did the shift solenoid replacement fix your limp mode?
@thebomberThebomber-yy2th Жыл бұрын
@@dcsco hello was it just a bad connection or did you had to replace the shift solenoid ?
@dcsco Жыл бұрын
@@jeremywilson8334 Yes it did.
@dcsco Жыл бұрын
@@thebomberThebomber-yy2th I had to replace the solenoid pack, and it wasn't cheap.
@jesuscruz-fv3vm6 жыл бұрын
good job man you make it looks easy, I will try to do mine thanks for your help.
@fuccillo1113 жыл бұрын
That's so clean! I'm doing mine today and I can't tell you already I'll be getting rust all in my ears and eyes as it's a ny truck
@juancastro69343 жыл бұрын
Phoenix wheather. Little rain, no snow and continious washing keeps it rusy free.
@mikeready92284 жыл бұрын
So a couple things I learned doing this on an 06 dodge Dakota 4x4 with 4.7l engine. Before you pull the release on the plug their are 3 or 4 little clips holding it in place at the top you have to release them with your thumb before you pull down the white release just push them in towards the transmission. Secondly for this truck you had to remove the transmission support cross member 2 bolts on each side and four nuts under the support. other than that it went pretty smooth.
@clockworkbike5 жыл бұрын
Wow, your truck is CLEAN.
@juancastro69345 жыл бұрын
LOL, Thanks. I always keep my cars clean to make it easier to work on them. Plus, living in Phoenix makes it easier to keep them rust free and clean all year.
@bigjohnharvey6 жыл бұрын
Great video. Thank you!
@terrylewis43025 жыл бұрын
thank you for this video,you saved me
@rasfassalazar2150 Жыл бұрын
Thank you so much for this video 🙌🏼💯
@Route5nMotive5 жыл бұрын
awesome video, very informative
@marcocortez42986 жыл бұрын
Thanks Juan carlos,it was the problem,the plug conecciones
@miguelcastaneda72365 жыл бұрын
Marco Cortez same couldnt figure if lifted .pushed or what ...plastic didnt wanna break
@jimmcgettigan13265 жыл бұрын
Very helpful video👍
@calucogalicia2 жыл бұрын
Thank you for your video I I'm working on my truck and I stock removing the solenoid switch
@juancastro69342 жыл бұрын
Caluco, hope the video helps and best of luck.
@jeremywilson83342 жыл бұрын
good job. Thanks for the details
@donnieabreo8855 Жыл бұрын
Thanks for the video ..great help
@kt99344 жыл бұрын
Thank you that was a good video you did a good job thanks
@appleovereasy3 жыл бұрын
Great video I have no backup lights and have traced problem to neutral safety switch. Strangely I do not seem to have the 2 most common switches and this solenoid seems to be there in its place. I'm assuming I can get the harness from the solenoid to the engine. Hopefully as all gears work fine etc. and shifting too
@joshuathebaptist67352 жыл бұрын
Did you ever figure it out? I'm having the exact ae problem on my dodge ram. I'm trying to figure out if changing this part will make my NSS work properly & not leave me stranded whenever it feels like it.
@WaveAction7774 жыл бұрын
What issue did the transmission have when it had the problem? Did it not shift in all gears? Was the shifting slow through the gears?
@sexycaprisun Жыл бұрын
Thank you. Very much
@caspharris16 жыл бұрын
Dude you safe me a lot of cash, thx
@lopezgirl19875 жыл бұрын
Lol
@pedrogomez90772 жыл бұрын
Thank you
@elisaartis35604 жыл бұрын
Does anybody have any Info if this will work on an 08 ram 1500 5.7 just found out that shift solenoid A needs replaced
@wassimjacob94855 ай бұрын
Thank you for the video. I am about to replace the solenoid on my 2005 ram 1500 . i have codes p0700 and P0755
@juancastro69345 ай бұрын
Hopefully it helps you with the job. Don't remember anymore what codes I had, but I did mention them to someone's comments a while back. Best of luck
@darthfader30496 жыл бұрын
Did this originally cause a code to kick in your truck? Mine is an 04 Ram with the 5.7 hemi 2 wheel drive. I notice it lags big time to accelerate after reaching cruise speeds. I have to push the gas pedal hard or the tow button to pass up cars. Seems to slip slightly sometimes as well but otherwise seems fine. Lower gears are perfect, but I also dont have any codes right now
@juancastro69346 жыл бұрын
Leonardo olea Originally I had a code for "transmission Solenoid Malfunction". Don't remember what code itvwas but it was specific to that part
@ramcummins05214 жыл бұрын
Before you change this did your transmission shift hard
@dennisboyer67414 жыл бұрын
05 Dodge Ram 1500 4x4 5.7L with 158000 miles I did a lot of research on this and the dealer wanted $420.00 for the solenoid pack which Is made by Dorman. Carid has a (REMAN.) for $209.37 and was done by Dorman but the core charge Is $300.00 but they didn't waste any time giving the core chargeback. I have used a lot of reman. parts through the years and have been just as good and this Is the updated pack. I also got a Sonnax line Pressure Booster kit. RFE-LB1 for all RFE transmission's $50.00 on ebay. Everything I got online and it oem.
@dinkbuster14 ай бұрын
Have a 2006 4.7, po871 code. Reset computer it shifts fine for about 25 miles or so, then after shutting off truck for a few and restarting and driving off, lose the shift at 45 mph and OD at 60. Other than that shifts fine, no slipping. Would this solenoid cause this?
@toad91232 жыл бұрын
Installed one now I have a no start condition and are the gear selection on the dash are all selected at the same time, anyone seen this?
@beebacheeba2 жыл бұрын
Nice video! Do you know if there's any chance of misalignment with the actual physical shifter when reassembling? Does the solenoid need to be checked for proper alignment or does it always come in the "park" position?
@beebacheeba2 жыл бұрын
I would imagine you just hold the new side by side with the old and make sure everything is in the same position.
@juancastro69342 жыл бұрын
Greg, no alignment is needed since it's an electronically contrrolled part
@jeremywilson83342 жыл бұрын
My 03 Ram is not giving off codes and shifts fine. Problem is it goes into limp mode every few minutes. I've replaced everything except the shift solenoid so I guess that's next. Too bad it's over $400 at the dealership.
@omarbofoable2 жыл бұрын
Hello Mr Juan Castro great video! I had a question P0760 just came up on my 2004 Dodge Ram however whenever I turn the truck on there’s a whistle sound aswell kinda like a vaccum cleaner coming from the transmission would you say it would be the Solenoid?Any advice helps! Thanks!!
@juancastro69342 жыл бұрын
Ernest Gomez, whenever you hear vaccum like sounds in a transmission that does not have any vaccum pumps since the solenoid does all that work, it is very likely some kind of bearing or another metal on metal type of friction such as clutch plates. Best of luck.
@eddieq75675 жыл бұрын
I recently had the same issue, since I bought my truck about three years ago it would kick and turn off at red lights and stop signs. Finally it kicked and went limp a block away from my house it gave me p0755(solenoid) and p0944 (required transflush). The mechanic said that it could be that the trans is really dirty and that is why it is reading faulty solenoid so we went ahead and did the transflush. Ran good for two months then it started kicking again. Now I’m on the verge of changing the solenoid but my question is I showed my bro this video but he told me to be verry cautious when touching something in the trans and recommended me to hire someone to do it instead any feedback would be good
@juancastro69345 жыл бұрын
Eduardo, you are right about not wanting to touch the transmission if you're afraid of damaging it. I did it knowing that if I didn't get it to work I would have to take it to a shop and in reality I would have taken it to a shop anyway because of the shifting issue. Make sure you watch all the detailed stills I have in here with the location and torque (inch pounds, not foot pounds) for this job at time 2:22 and 5:50, as it would be one of the reasons for messing up your transmission if not done properly. Best of luck if you decide to do the job.
@charlesadams70022 жыл бұрын
Thanks for showing me how to remove that clip 🙂
@iTwitchHD5 жыл бұрын
Was wondering if you had any suggestions. I replaced my solenoid on my 2006 ram 1500 5.7 and the yellowish plastic clip broke on the plug in to the solenoid. Now truck wont start even when clip is pushed on. Can you buy the yellow looking clip separate and repair?
@juancastro69345 жыл бұрын
Two possible solutions. The easiest would be to take a picture and take it to your local dealer to see if you can replace just the clip or the entire plug. The second would be to go to a junk yard and look for one. Good luck.
@pandawillymofo65185 жыл бұрын
I short circuited my battery when my battery died and forgot i had the switch open now im stuck on high gear
@alex5357aaa6 жыл бұрын
Thank you for video. I have 2005 Dodge Ram 4x4 4.7 with 126k miles and it’s just jerks between 2nd and 3rd but no sleeping or any other issues. Any ideas why is that ? Thank you.
@juancastro69346 жыл бұрын
Alexander Fedorov wouldn't know what to tell you. In my case I had the truck since new and changed the transmission fluid every 20 tp 30k miles with no signs of clutches or metal wear. So, I knew it had to be an electrically control mechamism amd that's the main one in it. Best of luck.
@alex5357aaa6 жыл бұрын
Juan Castro Thank you so much for your response 🙏
@amandakeith43475 жыл бұрын
Let us know when you'll be changing both sets of plugs :)
@juancastro69345 жыл бұрын
Are you referring to the Spark Plugs?
@takingoutthetrash15122 жыл бұрын
After i change the trans solenoid or sensor, my truck still wont shift past 3rd gear... i need new ECM
@LeonelRodriguezcano4 жыл бұрын
How do you know if it's bad the solenoid vs the transmission?
@hassanharrison39863 жыл бұрын
Dunno if anyone cares but if you guys are stoned like me atm you can watch all the latest movies on InstaFlixxer. Have been streaming with my girlfriend these days :)
@joshuamohammed40933 жыл бұрын
@Hassan Harrison definitely, have been watching on instaflixxer for months myself =)
@gmdesignservices6 жыл бұрын
Hi, have a truck that starts off in 2nd and works. But cannot start off in 1st gear. Has the same error note. Will this work for me?
@juancastro69346 жыл бұрын
wouldn't be able to tell you if that applies to yours. Mine always had clean Transmission fluid with no residue in it and always started. However, when shifting it had problems down or up shifting.
@weldingjunkie4 жыл бұрын
What were you systems? I can’t get into 3rd 4th and overdrive I’m thinking it’s the shift solonoids
@lederrishale83084 жыл бұрын
Welding Junkie did u get it fix mines doing thevsame
@bryantwalker11363 жыл бұрын
Hey Juan I previously commented on this video saying it was excellent. I still say it is because I changed my solenoid pack with no problem (thanks again). But.....when I went to start my truck it wouldn’t and my shifter slid very easily not stopping in any gear??? Someone told me I should have adjusted the “linkage” to low or forward before finishing the job??? Do you know anything about that??? Thanks!
@juancastro69343 жыл бұрын
Thank you very much. The shifter linkage is mechanical and it's completely separate function from the selonoid which is and elecreical/mechanical separate unit. The shifter linkage has it's own mechanical workings. Email me at jmcastro001@gmail.com and I'll send you whatever info I have on that.
@aceofpace1378 Жыл бұрын
Did you figure it out?
@DjRezurrection2 жыл бұрын
Hi halfway done on my 2008 Chrysler aspen ..was it hard getting the connector back in ?
@juancastro69342 жыл бұрын
Robert Barnes, it wasn't hard at all to recconect the plug. Double check the plug on the new part to make sure you have the right part. Best of luck.
@nancysanchez66635 жыл бұрын
Hi... I replace the selenoide pack in a Dakota 2006 2w/d The codes desapear but the reverse now dont work Before with the old one was working ok I put it back the old one and still no reverse something were moved in the installation i think What do you think ??
@juancastro69345 жыл бұрын
If you loosen one or more valve body bolts and something was moved out of place, then that would explain the reverse issue. If you're not sure on how to work on a valve body and don't have diagrams and torque specs, then you'll need a transmission shop. Good luck.
@edgarhernandez54716 жыл бұрын
Did you do this because it wouldn't go out of 4th gear? I have an 09 1500 and it's skipping over drive and straight to 4th gear and I can't switch gears scanner saying it's why you changed here what do you think?
@juancastro69346 жыл бұрын
Edgar Hernandez I knew mine didnt have any worn clutches because I own the truck since it had 30k miles and change the transmission fluid regularly without seeing any residue or chunks in the oil.
@treyjeffers3326 жыл бұрын
Mine is doing the same thing. 09 1500 4x4. Skips over D both directions. The code is P0750 which shows Shift Solenoid 'A' malfunction
@mikeevans55835 жыл бұрын
I just purchased a 05 1500 5.7 hemi and the previous owner replaced it (twice) 1 used and 1 new. but it won t shift out of third gear. It hesitates when starting and shuts off when put in drive (sometimes).rough ideal... Smells lean/rich... Has a late response/ jumping/reduced power should I just get a new trans? Someone please help!!! Waiting on new diagnostic/scanner to arrive...
@juancastro69345 жыл бұрын
MFE, whe. I did mine I knew the transmission had no debris from the clutches or steel plates. If you're not sure and haven't owned the truck for years then just get ot rebuild. Best of luck.
@mikeevans55835 жыл бұрын
@@juancastro6934 thank you for replying... I've been waiting forever to purchase this truck... Could that be causing all of this to happen.. I purchased this I knowing it had this problem but it's super clean and I paid 1500 5.7 hemi 4 door 4x4
@juancastro69345 жыл бұрын
@@mikeevans5583 , it's a great deal. You can either get your it rebuilt or buy a rebuilt one that you exchange at places that do transmission exchanges. You could also gey a used one on ebay for about $500. These trucks are really worth repairing.
@tallll705 жыл бұрын
@@mikeevans5583 Unfortunately they drove it probably too much with solenoids not working, my friend had same problem on 5 year old Tundra, he drove it whole week, had to replace trans. too.
@victoradan11444 жыл бұрын
My started with a little bump when shifting! When I put it in drive it takes a moment to get in gear! Do you think it's the solenoid?
@juancastro69344 жыл бұрын
Not sure Victor. If your transmission fluid is clean and has always stayed clean with not too much metal fragments and debris in the pan during transmission services, then it could be the solenoid. Mine did give me a code that was specific to the transmission solenoid and I had always done transmission services myself. Best of luck.
@victoradan11444 жыл бұрын
I serviced it not to long ago! I'm going to check and might get it changed
@victoradan11444 жыл бұрын
Thanks by the way 👍
@rich351w5 жыл бұрын
Hey juan awesome video, i was wondering what transmission do you have?
@juancastro69345 жыл бұрын
Richard, I believe mine was the 45RFE. I did not include model or more details since the solenoid replacement is applicable to multiple similar transmissions. However, I found it useful to download the technical manual from ATSG for $30 and it gave me the torque specs and other stuff needed.
@rich351w5 жыл бұрын
Ok awesome thanks i will keep that in mind.
@osirisnero8641 Жыл бұрын
Hiya Juan, do you happen to have the part number for that shift solenoid?
@juancastro69349 ай бұрын
Video time point 4:10. Dodge part 6835-3383-AB
@manuelgastelum36052 жыл бұрын
How much fluid did it take to fill back up after this procedure
@juancastro69342 жыл бұрын
I think I used almost two gallons.
@gabrielsalazar6648 Жыл бұрын
Why did you change this part.what was going on with tour transmission
@juancastro6934 Жыл бұрын
@gabrielsalazar6648 I don't remember the code anymore, but the description was for "shift solenoid" and the transmission was not shifting properly.
@KingDevilCharger5 жыл бұрын
How many quarts of transmission fluid did you need total?
@juancastro69345 жыл бұрын
I don't have my manual handy right now, but I think i used 9 at the time
@KingDevilCharger5 жыл бұрын
@@juancastro6934 Awesome thank you Juan! I appreciate your response 👍
@tracysmith57855 жыл бұрын
How long did it take you to complete this?
@juancastro69345 жыл бұрын
About 3 hours since I hardly work on cars anymore
@mitchellmccormick95693 жыл бұрын
My dodge is shooting an obd2 code for shift solenoid f is this the right thing
@juancastro69343 жыл бұрын
Mitchell, very likely since the as you can see in the video it's only one and any mulfunction code related to the solenoid will likely be resolved by replacing it. Best of luck.
@jesusrodriguez1963jr4 жыл бұрын
What made you replace this part on your vehicle? What was the problem?thanks
@juancastro69344 жыл бұрын
Originally I had a code for "transmission Solenoid Malfunction". Don't remember what code it was but it was specific to that part. Problems shifting.
@jesusrodriguez1963jr4 жыл бұрын
@@juancastro6934 ok thanks for responding and for your video
@danielgallegos36222 жыл бұрын
Me puede ayudar gracias
@jeffreybates53272 жыл бұрын
I have a 05 Durango with 5.7 hemi I have a p0700 code and p2706 which says shift solenoid malfunction shifts perfect but occasionally goes into limp mode then I just restart then it fixes itself so you think this solenoid pack is what I have to change?
@juancastro69342 жыл бұрын
Jeffrey, if you're getting the code then the solenonoid would be the most likely first step. Best of luck
@jeremywilson83342 жыл бұрын
Did you replace the solenoid pack? Did it fix it from not going into limp mode anymore?
@jeffreybates53272 жыл бұрын
@@jeremywilson8334 yes I replaced the solenoid myself and now it drives with no issues been like 4 months since changed and no issues so far just make sure you fill the correct amount of transmission fluid took me 10qts to fill completely
@aceofpace13785 жыл бұрын
I replaced my shift solenoid yesterday. It would randomly drop into forth gear and stay there till I turned my truck off and started it again. It would be good for a few weeks and it would do it again. Once I out the new solenoid on it stays in forth gear no matter what I do. I reset the battery and and fluids are perfect. What else can I do?
@juancastro69345 жыл бұрын
I'm no t sure how familiar you are with Valve Bodies, but that could be the problem. Best of luck
@MichaelAMyers19574 жыл бұрын
Have you figured out what the problem is ?? My ram will shift into 4th and stay there
@aceofpace1378 Жыл бұрын
@@MichaelAMyers1957 he bud just saw your comment. I ended up putting my old one back in and it worked. But now it is acting up again. I've changed the fluid 2 times. It works good for a few months then it goes back to going into limp mode. Its driving me nuts.
@MichaelAMyers1957 Жыл бұрын
@@aceofpace1378 man, get this shit. at the time I had 2010 dodge ram 1500 quad cab, got it in 2014, my brother had it before me. The shift solenoid went out a few days after I had plate an screws put in my ankle. Like a DUMBASS I ordered one off ebay. It shows up, I go crawl under the truck, cast on my leg an all. Replace the damn thing, of course it wasn't the correct one for the truck. So here I am, covered in fuckin tyranny fluid, just had ankle surgery like 6 days before this. I pull the sumbitch out, put the original back in so I can atleast drive to doctor in 4th gear. Put the original back in, something came loose inside the damn Transmission so my gear shifter would just move freely an wouldn't register to any gear. I checked everything outside the tyranny that could possibly be the issue but it was all good on the outside. Ended up getting a pretty good tyranny for cheap an had the whole tyranny replaced after that.
@aceofpace1378 Жыл бұрын
@@MichaelAMyers1957 i just about to that level. I'm so tired of dicking with this thing. A couple months ago (before I changed the fluid the second time) on my way to work, it down shifts. I turn it off at a stop sign like normal but now it won't start. I had to push it across the road to a store so I wasn't blocking traffic. My dern fuel pump went out on top of the crap shift solenoid. I had it towed . Got the fuel pump fixed but this transmission won't let up.
@ballislyfe5814 Жыл бұрын
Hello what kind of transmission is this?
@juancastro6934 Жыл бұрын
45RFE
@javysknowhows22884 жыл бұрын
Juan what code did you get I’m getting just a p0700
@juancastro69344 жыл бұрын
From wha i read, that code P0700 is usually accompanied by another more specific code. In my case my truck had the P0750 code.
@supplementDUDE3 жыл бұрын
I'm just getting the P0700 code too. What was your fix?
@adrianloma176910 ай бұрын
That clip that you disconnected that connects to transmission - does it need to be flush or is there a little gap 1:05 video mark - I seen you pryed it with you flathead
@juancastro693410 ай бұрын
That red clip is a security clip for the plug and when you put it back it will go all the way in and you'll feel a click.
@juancastro693410 ай бұрын
That red clip is a security clip for the plug and when you put it back it will go all the way in and you'll feel a click.
@rogelioreyes90524 жыл бұрын
What was reason for replacing solenoid?
@juancastro69344 жыл бұрын
Originally I had a code for "transmission Solenoid Malfunction". I had been replacing the transmission fluid and filters every 10 to 15k miles and never had any shavings or residue, so I knew I didn't have any parts wearing out as well.
@user-wt4xl9oz5p5 жыл бұрын
I have durango 09... And I have error code p0714... What part need change??
@juancastro69344 жыл бұрын
The first thing you would need to do is check your transmission fluid. If it's too old it can be overheating and giving you the code P0714 (Transmission Fluid Temperature Sensor Circuit Intermittent"). If your fluid is good then you'll need to replace that sensor. Best of luck.
@dcsco3 жыл бұрын
Wow, your transmission is the cleanest one I have ever seen. It looks like a new vehicle. Did you degrease it?
@juancastro69343 жыл бұрын
No degreaser. Arizona's dry weather keeps it dry and makes it easier to keep things clean
@dcsco3 жыл бұрын
@@juancastro6934 Holy cow, That almost makes me want to move to Arizona, but not quite... LOL Thanks for your reply! Still I wish my transmission looked as clean as yours!
@zackablett29182 жыл бұрын
So out of no where my 04 dodge lost all gears could this be the issue?
@juancastro69342 жыл бұрын
Zack, if you got a code for it the you'll need to replace it. Otherwise, it could be many other things
@SofaKingSkilled4 жыл бұрын
Why was this replaced. I have a stalling issue when I put mine in gear.. as if converted is locked up instead of free spinning
@juancastro69344 жыл бұрын
In addition to the problems shifting, I had a code specific to the shift solenoid (P0750)
@jeremywilson83342 жыл бұрын
Sounds similar to what mine is doing. Did you ever figure it out? thanks
@treyjeffers3326 жыл бұрын
How is it so clean under there? lol
@juancastro69346 жыл бұрын
Trey Jeffers, lol. I keep the engine compartment and drivetrain in all my cars clean. It makes it easier to work on them and spot oil leaks.
@connerpennington37972 жыл бұрын
Was your hard shifting
@juancastro69342 жыл бұрын
Conner, mine had the Shift Selonoid code and was hard downshifting.
@Grady006832 жыл бұрын
What did the new solenoid cost
@juancastro69342 жыл бұрын
@Aaron G: at the time it cost me around $250 from the dealer. I hear now it's 4 to 5 hundred.
@cinema6r8456 жыл бұрын
What about for a 1500 97 dodge ram? It says I need a shift solenoid but I can't seem to find it or it may not have one .it a 42HR transmission
@juancastro69346 жыл бұрын
Cinema 6R I'm not sure if that year has the same transmission. I think mine starts with the 2002 model
@luisc69524 жыл бұрын
Go to geek auto parts on line
@idahospyder16204 жыл бұрын
How did you determine that you needed to replace this and did it fix your problems?
@mintone20083 жыл бұрын
Diagnostic machine gives you the code
@edwinbenitez5022 жыл бұрын
how many quarts of oil does the transmission need?
@juancastro69342 жыл бұрын
If I remember correctly I think I used two gallons of ATF4
@edwinbenitez5022 жыл бұрын
@@juancastro6934 ok thank you
@khushhalpakistanzindabad46804 жыл бұрын
How much transmission fluid to put in on a complete drainage. Sir.
@juancastro69344 жыл бұрын
Khushhal Pakistan, since it's a service and the transmission is not fully drained due to fluid left in the Torque Converter, the 45RFE transmission takes 5.2L on a 4x2 truck and 6.2L on a 4x4 truck. That's about 5.6 or 6.5 US Liquid Quarts respectively
@khushhalpakistanzindabad46804 жыл бұрын
@@juancastro6934 Thanks for your answer. I have one more question. After you replace the solenoid pack, did you have to reprogrammed the TCM.
@juancastro69344 жыл бұрын
@@khushhalpakistanzindabad4680 Fortunately, the truck's ECU detects the new part and the code goes away within a day or you might have ro erase it with a code scanner. There's no programming of any kind, and if the code returns you have a different problem.
@khushhalpakistanzindabad46804 жыл бұрын
@@juancastro6934 Thank. Appreciate. It is a very nice video.
@Chocolatemilk2percent Жыл бұрын
what was the reason for changing the solenoid?
@juancastro6934 Жыл бұрын
@Cam-ny8hv I was getting codes and from one of my prior replies: From what i read, that code P0700 is usually accompanied by another more specific code. In my case my truck had the P0750 code. Hope this helps you!!
@Chocolatemilk2percent Жыл бұрын
@@juancastro6934 not really helpful LMAO im looking for a different answer. was your problem a shake when it was in overdrive and so you replaced the solenoid to fix that? I guess im asking what was the problem caused by a bad solenoid lol
@juancastro6934 Жыл бұрын
@@Chocolatemilk2percent Sorry @Cam-ny8hv, mine was having shifting problems (delayed and/or jerking) and my truck at the time had very low miles and I had changed the transmission fluid every 10 to 15 thousand miles with no signs of wear. Hope this answer helps
@Chocolatemilk2percent Жыл бұрын
@@juancastro6934 much better lol thanks. My truck shakes when it shifts into overdrive so i was hoping you had the same issue.
@cjhudson7734 жыл бұрын
What was your total time accumulated?
@juancastro69344 жыл бұрын
Please elaborate on you question. What do you mean by total time accumulated?
@cjhudson7734 жыл бұрын
@@juancastro6934 like time from start to finish
@juancastro69344 жыл бұрын
@@cjhudson773 since it was the first time and I was reading the transmission service manual to make sure I did it right, it took me about five hours. If you follow the video it shouldn't take more than 2 to 3 hours tops.
@JERRY602856 жыл бұрын
My truck its like it gets stuck 2nd gear, wont down or up shift...i turn off the truck and start it back up it goes away...I could probably drive it another while and issue will come back again,repeat the on and off and its good again...will this fix the issue??? Please help out
@28BIGNORM6 жыл бұрын
Jerry Carreon hey sounds li’e 2010 Ram 1500 Hemi. A friend & I changed out the Solenoid got a New Unit From auto store also ew Trans Pan with drain plug in it just in cases have to do it again. Now Runs Great again.
@gabrielsalazar664811 ай бұрын
Did this fix your problem
@juancastro693411 ай бұрын
Yes it did
@luismontemayor57134 жыл бұрын
Did you put in new trans fluid?
@juancastro69344 жыл бұрын
I did. Two gallons of Type 4.
@luismontemayor57134 жыл бұрын
@@juancastro6934 o ok thanks. How much did you paid for your part
@juancastro69344 жыл бұрын
@@luismontemayor5713 At the time I paid around $250.00 for it. I bought it directly from dodge and the part Number is 6835-3385-AB. If you're not sure it that would be the right part, call Dodge and give them your Truck's VIN and they'll be able to give you the right part.
@luismontemayor57134 жыл бұрын
Thank you sir i will do that Thank you for your time
@rich351w5 жыл бұрын
Alsow how much was the shift solenoid at the dealership?
@juancastro69345 жыл бұрын
At the time I think I paid around $200 for it. so I didn't see a reason to risk it with the aftermarket parts. If you go to the dealer with your VIN they give you the right one for your truck.
@rich351w5 жыл бұрын
@@juancastro6934 ok thanks, thats my plan i really dont want to re do this process if i get a remanufactured one. Im going to the dealership as well thanks to you.
@rich351w5 жыл бұрын
P2706 shift soleniod P0700 trans control system (mil request) These are the two codes that are popping up, do you think its the solenoid pack???
@juancastro69345 жыл бұрын
@@rich351w that seems to be two separate issues. If you need both parts there might be a lot more problems than simple electronics. You could either get the TCM from a Salvage Yard or just bite the bullet and take it to a shop. Best of luck
@rich351w5 жыл бұрын
@@juancastro6934 do you know where the tcm is located? Im having trouble locating it. Looked it up and it was saying ot was on the left side by the ecm, but found no tcm there. Is there a different locating for the 4.7. My truck is an 05 by the way.
@marcocortez42986 жыл бұрын
I did that,and now my truck no start any ideaspease
@juancastro69346 жыл бұрын
Marco Cortez has to be something electrical. Make aure all your electrical connections were not disconnected accidentally.
@peterdriedger63256 жыл бұрын
I have the same problem. Did you find the problem?
@mitch56535 жыл бұрын
@@peterdriedger6325 same prob????
@marcoavila31876 жыл бұрын
I replaced mine too thanks to this guy but after that I got another code p0731 anyone know what is that for???
@juancastro69346 жыл бұрын
if you used a new part and the problem is not the forward clutch, then make sure the transmission oil and filters are clean and that the valve body was torqued properly. Best of luck.
@bisdaktvofficial15906 жыл бұрын
i have 2001 dodge ram 1500 put it on drive or reverse slip.anybody knows whats rong with it..
@brandonshelters5 жыл бұрын
If your vehicle is still having issues after replacing the solenoid in the pressure sensor please watch this video. kzfaq.info/get/bejne/iLNxjbaeltK-fGw.html
@bientoramirez97552 жыл бұрын
Loise y gual pero todavía se buelbe a poner el 4
@juancastro69342 жыл бұрын
@BientoRamirez, si el problema original de tu transmision era el codigo de malfuncionamiento del selonoide, entonces el cambiar el selonoide hubiese resuelto tu problema. Pero si no era ese codigo, entonces el problema es muy seguro mecanico y hay mucha probabilidad que se necesite reconstruir la transmision. Buena suerte en su proyecto.
@sandratenorio46985 жыл бұрын
Can anyone tell me the name of the part at 7:45? Please and Thank you.
@chequeb96115 жыл бұрын
Shift Solenoid
@Franker4205 жыл бұрын
look at title of video
@christianjahn41413 жыл бұрын
So this is the pack not the solenoid I’m so Confused now I have the part I need but I didn’t see it at all in the video
@juancastro69343 жыл бұрын
The solenoid pack is the solenoid. It's an all inclusive electromechanical part. See minute 9 of the video. Once I removed the valve body yhe only remaining parts inside the transmission are the gears
@christianjahn41413 жыл бұрын
So this part at autozone is called at kickdown solenoid, my engine light said I need a shift solenoid f what do I do , I got the shift solenoid and don’t look like I even have it
@juancastro69343 жыл бұрын
If you have it you'll be able to know by the plug on the ouside of the transmission. If your transmission code says solenoid then I suggest buying it from the dealer. I always get big job parts from the dealer so that I don't have to work twice if the aftermarker part doesn't fit or doesn't work. Best of luck.
@paulcooper9525 жыл бұрын
Awesome now come do mine
@jonnyboy36744 жыл бұрын
How much was the new part? Did you notice a difference in the performance after replacing it?
@juancastro69344 жыл бұрын
Jon, it was around $250 from dodge, and yes it immediately corrected the shifting problem.
@jonnyboy36744 жыл бұрын
@@juancastro6934 thank you buddy, I might look into this unless I'm having issues with my friction discs?
@brym34522 жыл бұрын
I changed out my solenoid, filters but my truck still in limp mode. 🤷🏻♂️
@juancastro69342 жыл бұрын
Reset the code and if the Selonoid replacement worked, it shoudn't come back
@brym34522 жыл бұрын
@@juancastro6934 how do I reset the code ???
@juancastro69342 жыл бұрын
@@brym3452 With and OBD scanner, or have them donit at Autozone
@edinmerrivera4021 Жыл бұрын
Porque el titulo esta en español y hablas inglés?
@juancastro6934 Жыл бұрын
El título esta en Inglés. Probablemente tu browser lo tradujo sí esta en los settings de español. Regularmente si alguien tiene alguna pregunta en español a cerca de mis videos, además de inglés habló también español y les puedo responder en español
@KobeCorona-uj3zb3 жыл бұрын
I did all this work my truck still stuck in limp mode
@juancastro69343 жыл бұрын
COBE 1984, if your car didn't have the code for the solenoid, replacing it would not make a difference. If it did and it didn't help, you'll need to take it in.
@KobeCorona-uj3zb3 жыл бұрын
@@juancastro6934 I notice I was low on fluid i’m going to add more transmission fluid check the connection for the shift solenoid ... and disconnect the battery . Finger crossed