Yes I think a cotter pin would be easier to change

or put the dolly on the side and hammer the rims to push out the lock washer which is 5/8 of an inch

No we can't see this haha

I hope u know how to record now after 8y, put the camera in the area that you want people to see, simple but u fail. I just use a nail instead of pin.

Can you use butane propane mix cartridges in the lumogaz 206 it's the older metal bottom type thanks

Believe it or not, it's called a "DOLLY". "Dolley" is a woman's name.

Take a big hammer to the backside the wheel it will take off the ring and you should be able to reuse it

That ring that is hard to remove is dangerous, it only works on the cart if you are moving light stuff and there is no strain on the wheels. My cart had lost it long time ago probably when I hauled washer and dryer. Dangerously without realizing I had lost that ring, I hauled my Yamaha amp. Thank to my lord, the wheel did not came off while hauling the amp. I solved my problem with double split clamping shaft collar.

Really good info but really bad video shots

Next time u want to make a video how to change the tire in ur dolly u have to actually see what ur doing, sorry just my opinion

That also looks to me a large size mantle, you need a small sized one

After you get the washer and wheel off, drill a hole in the end of the axle and install a cotter pin. Much easier to change the next time.

Sorry but you don't have a clue what your doing you've done it all wrong 😂

I am unable to remove the cap on the wheel. You didn't show how to remove the cap.

Miss your content Bro. Hope you are doing well

Amazon carries the lock washers and they have tubes for the tires too.

Wow. Thank you. These things are a real pain.

It’s too bad the scope mounts on the ass-end like that- should’ve been a cantilever like the Browning SA-22, so your ready to go and sighted-in when it’s hooked up. Solid lockup though, so maybe this is a nonissue? Please show me how to install the optic rail with a Phillips screwdriver...🥴 lol. That is called molly webbing btw, and the D-rings are for “Alice”-style straps. As in; backpack straps, bud. Not “like a purse”, or “diagonal” as you imagine. It’s so you can wear it as a backpack...

What would happened if one would damage the mantle ?

All you need is a hinge clip or hinge cap! Lowe's or Home depot

Thanks great good idea with the hinge pin!

Use a flat edge screw driver and a hammer to lightly tap around the edge of a push knot. That will spread them hem open enough to free it up. Tap it with a hammer to close it once it’s off and reset it. That simple.

Tractor supply carry them

Let's see. I use hand trucks for moving around mostly boxes, stacks of stuff, small appliances, etc. Not so much ammo. #myloss

Piece of coat hanger wire works.

Like you I don't like to throw things away. Got two dollys to replace their tires. One has holes n the other one doesn't

Good job, you can do it like this to kzfaq.info/get/bejne/gt92e86qtquVhqM.html

Thanks for the video, exact same problem

The washer looking fastener is called a bunch of different names: Push Nuts, Starlock, Star Washer, Speed Nuts, Push Ons, Push On Fixes. Unfortunately I still couldn't find the size I needed in stores.

Wowwww

Cool vid

Thanks for doing this video. I bought one of these because I live in Florida and we are in hurricane season and I wanted to make sure that I can cook even if the power goes out for a couple of days or even weeks. Then I realized I don't know how to use one of these and if the power goes out I might not be able to get on KZfaq. I got mine on Amazon and it's brand new and everything but it didn't come with any instructions.

3:48 , 4:00 😲😲😲😲😲😲

Just ordered a hardly-used one on eBay. Looks like I made a good choice. It has an attachment so you can fasten the scope to a table.

Hay brother, Just a word of advice. keep the gun half cocked while closing the breach because the firing pin sticks out a bit. If you don't when you squeeze the 2 parts together, you can bend the firing pin or even worse you risk shooting yourself in the hand.

How much?

break in period

How 'bout THIS for cool factor: I had problems with jamming from the first day, back in '75. Fixed it by inserting a wedge-shaped flat-head screwdriver into the receiver of the barrel, and twisting it to create a minor chamfer so that the rim of the receiver wasn't just a sharp edge all the way around. Worked like a champ since then, never jamming even ONCE for the next 40 years! Even when it ACCIDENTALLY went FULLY AUTOMATIC for a couple of years. Turns out the firing pin had gotten some slack in its track, and was slamming the rims of the cartridges EVERY TIME it auto-loaded! It would empty the 8-shot clip in less than a half second, like it was single shot!!! It would throw the empty casings ten feet or more, so that if someone was standing to my immediate right, they would get pelted by all 8 casings in less than a half second!! Naturally, I knew full well I would eventually have to repair it so that it would be somewhat safer (and legal) in semi-auto mode. I eventually bought new parts in 1980, and it has functioned PROPERLY and FLAWLESSLY since then. I have dispatched HUNDREDS of rattlesnakes with it in the Matagorda Bay area in Texas since 1975!

Looks awesome. How do you remove the stock muzzle break?

Carry my 38 cobra every day. Its not a conventional trigger pull. if you think rock the trigger at the bottom, almost like pulling the trigger down, it works with little effort. So rock, dont squeeze.

my pmr 30 was a single shot until i cleaned the mags there was dirt and plastic shavings in them i put some dry lube in the channels and it works like a champ

I believe those holes in the gun are to create air pockets, for when its broken down. Making it able to float

Nice vid

Nice video but I hate that mag release

Just ran across this video. Good stuff. I can tell you that the smaller magazine you had is an 8 round Henry magazine. You can tell because of the "hairpin" metal wire that slides vertically along the side. That was part of Henrys redesign to make the feed more reliable. I did track a lot of the feed problems down to ammo since it relies on blowback. I have great luck with 40 grain round nose that does over 1300fps. It has enough energy to make the Henry feed quite reliably and the round nose doesnt hang up on the transition from the feed ramp to the barrel. The charter arms version is more spotty and I found that if I hold the magazine in place a certain way it keep the magazine feed ramp in a better position. Its still quite fun once you get it rolling though.

I have a Grendel P30. If I use anything other than Win JHP's, I will have occasional jams.

Damn. I bought one. And like a dumbass I'm over here lighting it and all I get is sparks. Then I was like maybe it needs the liquid my lighter has. But just to be safe I looked it up. It brought me here. Love how you explain it and showed it. And now I know. Thanks man!

The instruction manual says it will have fail to feed and failure to eject problems if you use anything less than 40 grain ammo. It needs a high power load to push the slide far enough back to make everything work right. They mentioned CCI Maxi Mag 40 grain as a good round for the gun

Awesome totally awesome wow what a little toys

Thanks recently bought the mossberg security 88,number 4 buck it is