Could you please help me, my ge spins but only at 50% speed and makes a grinding noise.i have had two different repair guys come out and they have no clue what is wrong with it. Please help thanks in advance

Did you ever make the video for doing this for a modern washer?

Mines make that noise after it's been running for about 30 to 40 min then it makes a loud humming sound

i have a kenmore 500. once it gets to the high speed spin cycle of the wash cycle i can hear it slip/ grind. do you think its the white part? clutch i guess it is?

Great instructive video! Thanks! Sure better than removing the whole drum and tub assembly! Question, my pads appear to be fine but maybe they need to be crowned? Mine are still pretty thick but might be flat and the washer is noisy on spin cycle.

Hey so I changed the tension suspension rods and now it’s not throwing the UL sign anymore but now the whole washer wants to jump across the room, but it is washing the whole load through without throwing a code

Balance is off had it replaced abd it jump.

Thank you. This video was a life saver for me, a non electrical wiring person!

What happened if they don't want to come fix it or replace it

Husband and I watching in 2024 and got our dryer hooked up. Thank you!!!!

Thanks!🔧

What is the problem if the pulley doesn't come off when you take the nut off?

What is the model #.i have the same washer but no model # (bought it used ). Cant order parts.Thanks.

Hi. How can I contact you

Thanks alot! I was gonna call someone to come fix it but im doing it myself!

Went put plug in its just letting water out

Looks like a can of worms. I'm going to save myself the headache and just buy the whole part

One of the best DIY videos on YT. Great detailed explanation and Academy Award for the camera man. You showed clear close ups at just the right angles. You da man.

Went for 20 seconds and stopped… hope that was long enough

Worked!!!

Thank you brother for making life easier . God is good folks!

I’ve replaced the heating element once already, as well as all of the other fuses, but the dryer stopped heating again yesterday. Upon inspection, the heating element was charred. I checked for lint and there was no build up. However, when I ran it not connected the wall, hot air was coming out of the top where the heating element is but not out of the exhaust tube at the bottom of the dryer. The wheel is good and spinning. Help…

Have you tried CT1? Its on Amazon. Perhaps other places/stores as well. Wonder if you could crimp on some type ring to the rod to prevent it from working loose? Just over the top of the part in question.

Dude, you are amazing, exactly what I needed to fix my old piece of garbage dryer! Liked and Subscribed!

Son says major thanks man you just "saved his bacon" on 4 prong install!!!

Great video. Which Whirlpool model is this?

Thanks!

Hello am trying to find suspension rod replacement for my Daewoo top loader washing machine,DWF-300GASEC. Help please

Excellent DIY self help video. Followed the steps and I was back up running and spinning in 30min. Never repaired a washer in my life. Thank you so much for posting!!👍🏼👍🏼👍🏼👍🏼👍🏼A+++

Gracias ! great video ! help me with my dryer 👍🏼

Just remember, any changes you make to a machine that changes the manufacturer design leaves you liable for any problems in the future. Manufacturers will not even allow a wire repair. FYI

This is the best video regarding this topic on KZfaq. I love the explanation and the demonstration so that I could actually be sure that the noise mine was making lined up. Thank you, when I get mine apart I will use your link!

Super video instruction!! Thank!

I have a Amana making buzz noise from motor and it’s not turning at all help ???

Is there an easy way to take out the nut?

I like your theatrics. Pretty cute. Otherwise very informative. Thanks.

My dryer would squeal at start-up and would "thump" quite loudly while running. After 40 years the belt broke. I replaced only the belt, now the dryer no longer squeals or thumps. FYI, I have a Kenmore and instead of clips at the bottom of the front panel there are 5/16" screws just like at the top of the panel. Do not remove those bottom screws, only loosen them and the front panel will lift upward and off. Good video.

Great video with lots of good information! Do you not normally change the springs unless they are broken and how often have you seen the balance ring cause vibration & shaking on washers like these? Thank you!

OMG I did this yesterday and my water was waaay worse. 🤮 My washing machine was second hand so I have no idea how old it actually is but it clearly needed this badly. I didn't need to wait 6 hours. Within 45 minutes the water was very dark grey and I could barely see through it. I didn't have the manual options to just fill and drain, so I set it for a large load, general clean with hot water. I made sure to set the Spin option to skip. I just added 5 scoops of oxygen bleach powder. I let it agitate for 10 minutes into the wash cycle, then just pressed the pause button. That's how I let it soak. When i was ready to drain it all, I pressed the Next button multiple times to skip all the steps until the last option, so it would automatically drain. I found the forced draining was too fast, and some bubbles were coming out of my bathroom floor drain, so I immediately hit Pause, and it continued to naturally drain, but much slower.

Very good presentation.

Hey I changed out my door switch and I have changed the push start button. The dryer makes quiet hum and does nothing any ideas?

Ebay is the Best place to sell. Just be clear in your description....

What are those plastic clips called?

Thanks, very clear instructions.

I have the pause play 6 light. I am having an extremely loud noise at the slowing or braking of the spin cycle. I have replaced the transmission, agitator plate. Thinking that was my issue. It was not. Please help.

Great video

I see at 9:42 of your video the spring bracket appears to be pretty close to worn thru.

I know I'm late to the game, but perhaps you could replace the original worn foam with cork, natural or synthetic. Drill a smaller than stock hole through the center of the cork, but keep the cork on the drill bit and hold a sanding block against the side of it while spinning the bit in a drill press to take the cork down to size. Then perhaps a slit down the side to get the cork onto the rod and press everything back together. Hope you find something that works!

I'll just keep my Lady Kenmore Series 90 (made by Whirlpool) set. Easy to use, washes things quickly, and super easy to work on in the rare occasion it needs something. I go through a lot of laundry in a week, and some of it is very dirty, I don't have time to fiddle around deciding what the washer feels like doing. It's ridiculous the garbage they sell these days.

I bought these machines about a year ago and have regrets. I am currently replacing the springs on the washer because they are already shot. It doesn’t clean the clothes and the dryer is a $500 dryer that you pay $1100 for just so it looks like the washer. For this kind of money, just buy the speed queen.