Stelios Liver

Пікірлер

@enisdurmishi4249 2 ай бұрын

Where can I get these specific drl?

@SteliosLiver Ай бұрын

Greetings enisdurmishi4249, Do a search in ebay with "1156/ BAU15S DRL & Signal bulbs" I bought those 2 years ago, and I don't have a preferred seller.

@tamamboylekalsn 2 ай бұрын

I have a giulietta which has blue&me. It seems my mic is not working properly. Can I use an aftermarket microphone on blue&me unit?

@SteliosLiver Ай бұрын

Greetings tamamboylekalsn, It could work, but I can't say for sure. I don't have a giulietta, and I 'm not using the default fiat audio source (this is an aftermarket erisin HU) In your place, I would replace the faulty part, with a new one with the same factory code on it.

@tamamboylekalsn Ай бұрын

@@SteliosLiver after my comment i found a topic in an italy giulietta forum. apparently you can use blu&me unit with an aftermarket mic but i havent tried yet. a new whole unit costs about 120 dollars in my country but a mic is about 5 :D i will try it, original one is not working properly anyways

@andreamarcelli3 2 ай бұрын

Needs a proxy alignment? Mileage blinking or not?

@SteliosLiver Ай бұрын

Greetings andreamarcelli3 , **The removal of default unit with the blue&you, requires a new proxy alignment.** The installation of an aftermarket HU (or any aftermarket audio source), is not configured as car default hardware, and therefore has nothing to do with the proxy settings.

@tahsinbatur7035 3 ай бұрын

Thank you so much. I opened the inside of the stepper motor and I was wondering "what could be wrong with this".

@SteliosLiver Ай бұрын

Greetings tahsinbatur7035, Thanks for your kind comment.

@jabbawonga3779 3 ай бұрын

Hi, I just wanted to say a big thank you putting this video together and sharing. It helped me hook up my 159 to a Sony XAV-6050 using the inbuilt mic. Worked perfectly first time with your wiring guide. Thank you!

@SteliosLiver Ай бұрын

Greetings jabbawonga3779, Thanks for your kind comment.

@RonnHogann 3 ай бұрын

Is this also available for IOS?

@Ahleen0 3 ай бұрын

ارجو افراد حلقه لطريقه برمجته تم الاشتراك للمتابعه

@Ahleen0 3 ай бұрын

كيف يتم برمجته

@leomonk974 4 ай бұрын

love the model, making it now

@nebojsabogicevic2881 4 ай бұрын

Is there any heat problem with resistors, do they release a lot of heat?

@SteliosLiver 4 ай бұрын

Greetings nebojsabogicevic2881, The resistors are used only with the flasher, so they don't see a lot of action.

@saveriomar5622 4 ай бұрын

Ciao, puoi darmi il link per acquistare questo prodotto. Grazie mille

@SteliosLiver 4 ай бұрын

Greetings saveriomar5622, Do a search in ebay with "1156/ BAU15S DRL & Signal bulbs"

@NoMadManKZ 5 ай бұрын

Total weight 6 x cap 428 gramm?

@SteliosLiver 4 ай бұрын

Greetings NoMadManKZ , yep... light and strong :-)

@NoMadManKZ 4 ай бұрын

@@SteliosLiver thanks 👍

@fionabruce2009 5 ай бұрын

Please do you have any new projects with the hologram fan at all

@SteliosLiver 4 ай бұрын

Greetings fionabruce2009, There is nothing planed for the near future. I 've designed the illusion of the helmet, to inspire my son, weeks before the real thing was created... Job was done (kzfaq.info/get/bejne/rMqWa6pzl9y9gac.html), and since then, we never went back to the led fan. This video was a complete guide, of how I managed to create my custom bin file. (which served me, as a motivator/appetizer)

@sinisahreljac9395 6 ай бұрын

Hi, please can you tell what projector lenses did you use? Link in video description does not work anymore. I've ordered Mini H1 Primo from Retrofitlab but does not fit; thread is too short so cannot mount and tight them. On your video it seems that you still use original bulb clamps, so how did you mount that projectors? As for all projectors that can be found original clamps should be removed.

@SteliosLiver 4 ай бұрын

Greetings sinisahreljac9395 , You can find the projector I 've used in this modification, by searching in ebay with the key [ 2X 2.5" Bi-Xenon HID Projector Lens RHD Car Headlight Hi-Lo Beam Shroud Retrofit" ]

@AshutoshDhaka 7 ай бұрын

helped me in a sticky situation <3

@SteliosLiver 7 ай бұрын

Thanks for your kind comment :-)

@TRHardware 7 ай бұрын

TPMS did not need any other modules to function? Just this aftermarket headunit and headunit found the 433Mhz TPMS sensors?

@SteliosLiver 7 ай бұрын

Greetings, TRHardware, The TPMS kit, comes with a USB 433Mhz receiver.

@TRHardware 7 ай бұрын

@@SteliosLiver Thanks for the info!

@johnanderson4903 7 ай бұрын

Unfortunately you went far too fast at the parts i needed to see. Im attempting to reassemble one which was taken apart by someone else and therefore need to see the order of assembly.

@henriquedelben 7 ай бұрын

what 3d modeling software did you use to create his iron man helmet model ?

@SteliosLiver 7 ай бұрын

Greetings henriquedelben, The model was from a 3d printout I did, for my son. kzfaq.info/get/bejne/rMqWa6pzl9y9gac.htmlsi=qYU5Rsy4qhTiIath The bin was based on the stl file.

@Gewehr2180 8 ай бұрын

This is literally the most useless CNC video on KZfaq! Please convay to me the meaning and purpose of this video's content. Did I miss something here? I saw two DC brushed motors and a CNC frame that was missing it's spindle and a video of a CNC router in a clear box that was taken from the other side of the room!

@SteliosLiver 7 ай бұрын

Greetings Gewehr2180 and thanks for your kind comment. I 'm glad you enjoyed this 7 year old video. (though a bit late) Like you, I can't find the purpose of this video capture anymore... I suppose, it made sense at the time...

@animedreams11 8 ай бұрын

hi, why didn't you connect the yellow cable and what is it for? Maybe I didn't understand the connection well . thx

@SteliosLiver 7 ай бұрын

Greetings animedreams, The yellow cable is the sensing cable for the dimming with the headlights on. It's connected to the "+" of the default headlamps. Check the bench testing in this video (same kit in my older car) kzfaq.info/get/bejne/e7qTlbKHlrDFXXU.htmlsi=cjRfOpsxpd8vQgFV

@LG-kj5qq 8 ай бұрын

Do you have your wiring diagram since the other video by John Fuller's wiring is not correct. Thanks,

@SteliosLiver 7 ай бұрын

Greetings LG-kj5qq, Sorry but this unit was in a different life time. I haven’t kept my notes for the printbot modification.

@antoniodelazzari8730 8 ай бұрын

Hi! I just connected pin 8 (MIC signal) and pin 24 (MIC GND) with a 2.5 mm TS mono cable (like the cable that comes with the aftermarket erisin mic) to the MIC-IN in the Head Unit. I used two Dupont 2.54 mm male pin, crimped to the two wires and insulated with a heat shrinkable sheath. In the settings I have selected MIC source as external, and the lowerest MIC gain. I can't get it to work, during the calls i hear some strange sounds and no voice. However if I use the aftermarket erisin mic that comes with the box it works. When I removed the Blue&Me I did a proxy alignment with multiecuscan to exclude the B&M module from the CAN settings (cause the KM was blicking in the cluster), but I think the original factory MIC should still work in any case. The factory MIC was working with the original radio. What could I have done wrong? What type of PIN did you use? Thanks!

@SteliosLiver 7 ай бұрын

Greetings antoniodelazzari8730, There was nothing special about the cables I used... I garbed the closest Arduino/raspberry jumper cables I found. I soldered them, to the unit default cables of the mic, and it worked.

@zachwy4187 9 ай бұрын

What type of metal tubing and thickness did you use?

@SteliosLiver 9 ай бұрын

Greetings zachwy4187, The tubing is stainless steel 314 with 2mm wall thickness

@NeiroAtOpelCC 10 ай бұрын

I don't know if there's a 15 connection somewhere in the area, but wouldn't it make sense to connect power from there to the odb pin 16 instead? That way it is on whenever the ignition is on and still wouldn't drain the battery.

@SteliosLiver 9 ай бұрын

True, but Ι only need the OBD BT adapter when I troubleshoot a problem, or when I 'm logging working parameters, and *not every time I 'm using the vehicle*. That why I chose this approach. This way, I can power on the module whenever I needed it. And I can also restart the module while driving.

@adrianleano6685 10 ай бұрын

Can this work with x5sa?

@SteliosLiver 9 ай бұрын

Greetings adrianleano6685, The x5sa has the same printhead mounting plate with x5s. So yes it can be mounted as is, onto an x5sa. With a few modifications it could be mounted anywhere, as far as you can tweak the motors supply voltage, the steps per mm, and the direction of the motor.

@myfavoritethings4504 10 ай бұрын

Hi Stelios, brilliant 159 content. I hole to upgrade to the same Head Unit. Can you still recommend it? One year later? Do I solder both Red & Black cables to pin 16 of the adaptor... im new to all the electrical stuff. Thank you

@SteliosLiver 10 ай бұрын

Greetings @myfavoritethings4504, The two cables of the JST connector are used to *interrupt* the power of pin 16 via a switch. You will *cut the cable line of the selected pin*, and you solder one cable *in each side of the line*. = This will enable you to cut power to one of the two outputs of the Y adaptor (the one that will receive the OBDII BT adaptor) The cable colors of the JST connector are irrelevant. Treat them as if they were both red. (since you are interrupting the + of the circuit). As far as the HU is concerned, I 'm still happy with it, though I bet there are better ones out there by now (don't know, don't care, since I 'm happy with this one) Would I recommend it? I can't recommend one product over the others, since I have experience only with the one I bought.

@kevin-qi7jr 10 ай бұрын

sir, are u buying fan only on website and u change style holographic in your self (after u got it fan) ???

@SteliosLiver 10 ай бұрын

Greetings kevin-qi7jr, This video was not about the hologram led fan. (there is nothing DIY about that... It's a product) It was about the DIY creation of custom content (bin files) for a led fan

@giacomoguajana 10 ай бұрын

Beautiful job. Can you tell me which lens is going? Thanks

@SteliosLiver 9 ай бұрын

Greetings giacomoguajana, The components I 've used for this modification, are mentioned in the video description.

@sphinxgr 10 ай бұрын

What was your initial problem? My 1030 has a very low flow when starts. Membrane is ok, but maybe it's old and not elastic any more

@SteliosLiver 10 ай бұрын

Greetings sphinxgr, The membrane was cut in the one you see in this video, and the water was constantly running.

@dimitriosvolikakis965 20 күн бұрын

@@SteliosLiverif the water flow is very low, what could the problem be?

@SteliosLiver 20 күн бұрын

@@dimitriosvolikakis965 Greetings, Check the membrane or/and you 9V battery.

@divinecouple1279 11 ай бұрын

Thanks for posting this video, exactly what I needed 🤓

@SteliosLiver 10 ай бұрын

Greetings divinecouple1279, Glad it was helpful

@eldancer2 11 ай бұрын

So...to make a diy hologram led fan all you have to do is to buy a hologram led fan...genius!

@zephsmith3499 10 ай бұрын

*DIY BIN FILES* for the (purchased) 3D led hologram fan Not (purchased or DIY) bin files for a *DIY 3D HOLOGRAM LED FAN*

@henry520119 Жыл бұрын

my LCD displayed some garbage during printing randomly , and recently I found probably ramps 1.4 12V for my Mega led the overheat crash. your video gave me another point !

@SteliosLiver 10 ай бұрын

Greetings henry520119, Glad it was helpful.

@ivancuetowicq Жыл бұрын

hello, does it work with a person standing?

@SteliosLiver 11 ай бұрын

Yep... Work's like a charm, with loads up to 90 kilograms. :-)

@TdtLUFwd Жыл бұрын

my steering wheel controls do not work, which CAN protocol are you using?

@aedflightcase Жыл бұрын

cool my friend😎😎😎

@SteliosLiver Жыл бұрын

Thanks for your kind comment :-)

@albertoharambour5885 Жыл бұрын

Thanks for the good video! You know where I can get a User's Manual?

@SteliosLiver Жыл бұрын

Greetings Alberto Harambour, The truth is that I haven't found a descent user. There was only a printed leaflet in the box, that was quite useless.

@backstagent89 Жыл бұрын

Hi. Which model Rear Cam did you use? thank you.

@SteliosLiver Жыл бұрын

Greetings Hristian Minkov, Just buy something with no infrared, and a 45 degree angle.

@user-fh6tb1vc8x Жыл бұрын

Hi How did you add that launcher (main menu design)? Was it installed by default?

@JoJanDiezel Жыл бұрын

It's an app called AGAMA Car Launcher.

@cosmefulanito5933 Жыл бұрын

Not DIY. You buy it.

@SteliosLiver Жыл бұрын

Greetings Cosme Fulanito and sorry to disappoint you... The pcb was bought. The aluminum plate was also bought The Kapton tape was bought The thermal paste was bought The working bench was bought. The used tools where bought. I think the only original part where my hands. I don't recall buying them, but I 'm not sure, since I was very young when I found them.

@russellwalker2787 Жыл бұрын

The worst DIY video with no explanation on your work, and slow it down a bit next time.

@SteliosLiver Жыл бұрын

Greetings Russel Walker, It was one of my first attempts, to share my hobbies with the community. Nevertheless, thanks for your comment.

@kevh3113 Жыл бұрын

not navi unit type .

@SteliosLiver Жыл бұрын

Greetings Kev H. You are correct. :-) ES8120R HU wont even fit in the facia of a factory default navi unit, so obviously the car was not equipped with a factory navi unit. (I don't know if they have a different mic, but I seriously doubt it.) Nevertheless thanks for your comment.

@marklimbrick Жыл бұрын

The rotor is instantly demagnetized if removed from stator! 2/3rds at least lost. I found this video searching for a clip in the factory showing how they are magnetized after assembly. It takes a very large current from a special power supply. Be curious and Google before dismantling.

@SteliosLiver Жыл бұрын

Greetings, marklimbrick, and thanks for your comment. The repaired nema 17 you see in this video, is still in use, in a heavily used, large coreXY printer, 2 years after the repair. **And it's not the first stepper I have repaired nor the oldest**

@aurenosetecnicotajimadahao7247 11 ай бұрын

When disassemble, it loss at least 20 percent of power. If your use isn't intense or near limits, no problem.

@RobbertDIYprojects Жыл бұрын

Nice project! Last summer we build a 3d printed bubble bazooka on our channel powered by a drone propeller. We shared our 3d models, feel free to use them. Lots of fun to build but was WAY to powerfull. I like this kind of projects. Keep it up!

@SteliosLiver Жыл бұрын

Greetings Robbert DIY projects, and thanks for your kind comment :-)

@MarkMichalowski Жыл бұрын

Matey, this is exactly, perfectly what I was looking for. I didn't even know the bearings COULD wear out! Thanks so much :)

@SteliosLiver Жыл бұрын

Greetings Mark Michalowski, and thanks for your kind comment :-)

@user-if4cy4be2u Жыл бұрын

THX!!!

@SteliosLiver Жыл бұрын

You are welcome. :-)

@zezinhoattube Жыл бұрын

Hi. Thank you for the video. I have a 159SW, where the power connects is on the right or left side? And… where exactly should the + connect to? Thank you

@SteliosLiver Жыл бұрын

Greetings José Moreira, You can see the plug and play connection here: kzfaq.info/get/bejne/nNVhjcdou5OyZqM.html And in this one, the connection of the factory default blue&me mic: kzfaq.info/get/bejne/jMiJdpRpp620nKs.html

@zezinhoattube Жыл бұрын

@@SteliosLiver thank you. But I’m talking about 0:54

@SteliosLiver Жыл бұрын

@@zezinhoattube oups... Sorry for the misunderstanding... I don't remember the colors, or the order of the cables... On the other hand, using a multimeter to determine the polarity, is always a good practice.

@realvipul Жыл бұрын

my one has electronic problem. when manual ON it the voltage comes on 9v but then when i off it it shoud come on again but with reversed polarity. but not volatge come out when i off mine. so water keep flowing out.

@Hansulf Жыл бұрын

I have an electric problem too... The valves are the same, but the system is not exactly this one. Everytime the thing tries to run, It stops and wont work again until I take out the battery

@Zigger2k Жыл бұрын

Thanks !

@davidBarrel Жыл бұрын

this is great, it deams automatically when you turn on the lights manually, but how the controller knows that? you just conect from the fuse box and "stole" power from a parking light

@SteliosLiver Жыл бұрын

Greetings David Varela, The installation is very simple. (you guessed right) The controller is connected: to the vehicle battery via a fuse and ** to the (+) of the parking lights ** The DRL: are automatically engaged, when the engine starts *and* the voltage exceeds 13V are disengaged, when a signal light is engaged are dimmed automatically, when the parking lights are engaged. (night mode) are disengaged, 30sec after the engine stops (follow me home mode) You can check out this video (installation on my other AR), that includes a bench test of the system. kzfaq.info/get/bejne/e7qTlbKHlrDFXXU.html

@ChampTruex Жыл бұрын

what do you think is a good fit for this machine i have have the same one and the stock board crapped out, would like a setup like what you have seems to work great lol thanks

@SteliosLiver Жыл бұрын

Greetings Champ Truex, After two years and many kilos of PLA, I 'm still using the setup you see in this video. (details in the description) Since then, I have added a 3d Touch (bltouch clone) kzfaq.info/get/bejne/qr1-a6aDlrO9aGw.html and I have implemented a dual Z motors auto align kzfaq.info/get/bejne/lZOaa6iX1LfUoYE.html The full story, is in this playlist kzfaq.info/sun/PLwWKwCy7r_VyTcHp6wP2SE3k5H_jnml3n

Ең жақсы KZfaq

Пікірлер