Have the same problem but the Cat is removed already. Sensor is brand new and errors acured immediately after deleting them. It needs to be elswere the problem.
@jacquesrousseau547210 күн бұрын
Looks like the guy who made this video doesnt want to share any Info where we can buy this Harness Kit.Very Dissapointed!
@godfreysautomotiveservices10 күн бұрын
I happily share the information where to buy the kit, the Facebook group he created is in the video description and if you read the comments you would see I share marks email with everyone who asks
@jacquesrousseau547210 күн бұрын
@@godfreysautomotiveservices Ja u Mentioned he has a Facebook page but that is it.The other bloke on the comment also states that he is unable to find this Mark guy on Facebook.Dont u have an email adress etc for him
@godfreysautomotiveservices10 күн бұрын
@@jacquesrousseau5472 yes, it’s [email protected] . This is shared on quite a few comments already
@jacquesrousseau547210 күн бұрын
@@godfreysautomotiveservices ok thanx for the info i will send him an email
@m.s.18311 күн бұрын
thanks master, I was looking for where this mouse is squeaking in my wheel. Regards.
@m.s.18311 күн бұрын
I also have a GLE and I have the same effect, the mechanics lubricated everything, there is no play anywhere and that fucking mouse on the driver's side is squeaking. It's some kind of defect in these Mercedes, they should fix it for free or the console will give them the money for the repair because they put those bumps everywhere that destroy the suspensions.
@capspampulha843311 күн бұрын
Se ligar e desligar o problema some? Meu carro deu esse cod troquei a aste mas o problema continua.
@themachine884212 күн бұрын
I have a 2021 GLE with 70,000klm is this a warranty fix or a regular service cost do you reckon?
@m.s.18311 күн бұрын
You have a full warranty for all mechanical parts for up to 3 years, they have to do it for free.
@themachine884211 күн бұрын
@@m.s.183 thanks I’ll call it in.
@larryreno829316 күн бұрын
It would appear that regular maintenance is something the owner doesn’t believe in.
@BollerRory22 күн бұрын
What year is this cla I have a 2018 would it be in the same location to replace ? And same part
@Edgedem23 күн бұрын
Zero help on the wiring bit 😢
@MecanicDeWeekend28 күн бұрын
You only need replace pump and injectors rest can be cleaned what you done is waste of money
@blackace442314 күн бұрын
I did cut the fuel filter but no metal shavings inside? Engine cranks but won't startt X5 25D F15. Also no fault codes :(
@geraldmichel7070Ай бұрын
Bonjour . video de grande qualité !!! merci monsieur !!!!!!!
@Jchiles29Ай бұрын
My srs door airbag is on
@asamitchell7948Ай бұрын
Cylinder 4 first to get air last to get fuel. When I had mine it had already had an engine replacement under warrenty previous owner my ownership I was onto my second engine after p4 went second engine I uprated the fuel pump and fuel pressure regulator with larger injectors and had Cylinder 4 slightly richer than the rest when I got it mapped p4 never went pop up to 280hp with a k04. Then I forged and hybrid ko4 went up to 300hp ran like a dream shame the m32 gearboxes are chocolate.
@shanebrookes1878Ай бұрын
Hi do you deal with Mercedes! Cheers need help please
@JesusHernandez-fz4cgАй бұрын
Thank you for this video. My GLB 250 picked up this code. Vehicle runs smoothly but will still address it. Two questions, did you use a gasket when you put the pan back on? And secondly, after you put back the oil pan. Did you put oil inside right away or did you wait for seal to dry? Thanks brother!
@godfreysautomotiveservicesАй бұрын
No pan gasket on these, just sealant. It’s fine to put oil in while sealant goes of 👍
@stugbroon16Ай бұрын
Do you need sealer where it bolts to head or is gasket itself enough thanks
@godfreysautomotiveservicesАй бұрын
Gasket is enough 👍
@stugbroon16Ай бұрын
@@godfreysautomotiveservices nice one cheers
@eddpowerАй бұрын
F**king hell - I thought that amount on the whiteboard was £970 until you read it out!! Phew!!
@akashicpurple3206Ай бұрын
I have a 2015 S550. I don’t see where I can just purchase ball joints without the entire assembly. Please advise
@imanifrechell5810Ай бұрын
I have an Infiniti qx30 having the same issue. Does this same fix apply?
@jozsefgyorosi537Ай бұрын
Bring back the ratchet type tensioner. As you rotate the crank you can see the poxy tensioner retracting back into itself. Its becoming a throw away society, 100,000K and send it to the scrap yard!
@7amdaАй бұрын
Replaced the lower control arm and it fixed the squeak noise. There is however a creaking or some sort of clunk that I can hear when steering and when going over bumps, any idea what this could be ?
@amslimauto2 ай бұрын
Hello, Thank you for the vidéo. I h1ve a problème please help me ! Il did exactely the same than you but my engin won't start after that. Do you have any idea please
@user-mu1rw1qr2u2 ай бұрын
Is that an Mercedes part number, Regards
@godfreysautomotiveservices2 ай бұрын
It is , yes
@user-mu1rw1qr2u2 ай бұрын
Hi, I have the same code P06DA00 I’ve just been to Mercedes for the same part, but my part number is different, 👍
@bigcharris67122 ай бұрын
Hi need some help here my car airbag light has come on also tryed erasing it on my obd2 scanner but keeps on coming back it says squib for the driver knee airbag has a malfunction open circuit B000413 code
@pawelszczepara17672 ай бұрын
I have start stop error vw passat cc after to change battery for new (battery is Coding) carista show 2 error 05462- Starter activation, return message terminal 50: Open/short to Ground (GND) 00458- Battery Monitoring Control Module: No signal/ communication
@satan85192 ай бұрын
Do you know where this list located on a 19 plate?
@wevved2 ай бұрын
What was the tape for?
@mashogagar2 ай бұрын
Honestly Merc is just a piece of shit
@ArtiActive-qn9dx2 ай бұрын
Hi, I think I have a similar issue which no one can diagnose, I’ve changed sparks, coil and injectors but cylinder 3 keeps miss firing but only when the cars warm/ hot id say approx 20/30 mins in to a journey but when the miss fire happens then it renders the vehicle un drivable so atm I’ve only been using it for really short trips would you say this is the same please advise
@jasonwyatt65692 ай бұрын
You make it look so easy, I bought an LR Towbar and all the additional parts, can't get anyone to fit it. LR will only fit their own supplied towbar.
@jrjohansen1002 ай бұрын
Why did it get wet in the first place??
@Michael-ry7rz2 ай бұрын
I have this exact problem on my c250, you’re a hero
@CaptnSpaulding2 ай бұрын
Is it possible to fit a towbar to a Ford Puma and what would be the cheapest one inc fitting? It’s only for a bike rack, not to tow anything. Thank you :)
@TheMavicz2 ай бұрын
Kits well cheaper other places same qaulity same kit
@godfreysautomotiveservices2 ай бұрын
Good to know 👍 customer sourced and supplied this kit
@masonhalpenny38483 ай бұрын
What size torx bit?
@JuanKlopper3 ай бұрын
How can I get this to South Africa
@godfreysautomotiveservices3 ай бұрын
Email Mark 👍 email in the below comments
@PingDrv003 ай бұрын
Why did you not show actually replacing the wastegate on the video? Is this something that can be done. Also, you did use the Mamba part correct?
@godfreysautomotiveservices3 ай бұрын
Because we didn’t replace the wastegate, we sent it to midland turbos to carry out as it says in the video 👍
@PingDrv003 ай бұрын
@@godfreysautomotiveservices I got you. Appreciate the response was hoping it was something that you did to increase performance of the turbo not just the waste gate. Great info though and appreciate the response!
@TheMalavikaraj3 ай бұрын
This is the exact problem My car has , i have a C 300 . how much would it cost me to get this problem fixed? Thank you in advance , this video was very helpful
@4x4bvs3 ай бұрын
Good video mate about time Ford are pulled up for this how many serious accidents have been caused with vehicles running into the back of another with no brakes and the driver blamed with no investigation
@garypreston63003 ай бұрын
Hi it's it better to put a new piston in or for one that has been used thanks
@tomthompson74003 ай бұрын
turning an engine backwards is no way to gauge chain wear. These engines need an oil flush and fresh oil every 6k from new ,,, long service intervals kill modern engines.
@challakebede59823 ай бұрын
Can you help me pls,can you show to me cylinder head temprature sensor location .
@bootstraptv49123 ай бұрын
quick question, if i did this on a r50 mini cooper park lane and put that engine in, would it be as simple as the swap you just did, ie plug n play u take one out put one in and ecu etc works ?
@handycrowd3 ай бұрын
Nice job! When I first read years ago that the timing chain was on the back of the engine I had to look to make sure it wasn't April the 1st... I hope you're charging good money for this job mate, I'm seeing everything from 1500GBP to 4000GBP (dealers) with most places settling in the middle somewhere. It's hell of an involved job and not without risk, so you've got to make it worth your while. I know for a fact that loads of places are saying "nope, not interested"... There must be getting on for 2 million Ingeniums out there now, don't know how many are diesels, but I think it's safe to say this won't be the last one you get asked to do lol! 🙂
@jordash1693 ай бұрын
Keep it short and sweet felt myself skipping 80% of the video to listen to actual information I needed not just conversation with the camera
@cbbaycycles3 ай бұрын
I spent just shy of $4.5k to repair/replace the timing chain at 70k kilometres. So disappointed the dealer didn’t identify it. Oil change interval way too long. 32k or 2 years. The repairer recommended oil changes at 6 month intervals… quite a difference. Even though I love the car I am so Disappointed in the product.😕
@danthecarman84403 ай бұрын
Great video mate. Was the timing cover hard to get off with that sealer stuck on ? I just subscribed.
@godfreysautomotiveservices3 ай бұрын
No, not that hard. Will take a bit of prying but once it starts coming it’s easy enough 👍
@danthecarman84403 ай бұрын
Thanks for your reply. Another problem I've come across is trying to undo the inlet cam sprocket bolt. It's way too tight and couldn't move it. Good luck with your new workshop.@@godfreysautomotiveservices