if it does work, i'd be tempted go in do a shift kit on valve body or if cheap enough try it all in one go.

Thanks

Nice one., what was the part no. or where did you buy it.

Great vid butttt the wipers blade they have a mark on windshield where they are suppose to be

Thank you for great video. Very helpful, especially with the electrical plug. Well explained.

can't wait to watch this. it comes up when searching 6th gen maxima trans solenoids. wonder if it's the same.

Thank you so much for this video, great job. It took me three days to get it out and it is back in again and I will finish it tomorrow hopefully. BTW, the special plastic parts holding the wire-harness to the engine block I bought on AMAZON. I think I paid $12 for 20 pieces. To get the two difficult to get to bolts holding the engine and transmission together, I took a couple of moving blankets and laid them over the engine. Laying on my belly on top of the engine I got to the two bolts as I kind of new where they were. Your video also showed me that I could actually do it as I saw you doing it.

It's pretty common to hear the words it's pretty common on this 04 yukon

This is the exact video I’ve been looking for.

How do you tests a 2 speed fan?

Incredible video, well shot and extremely in depth and informative. Thank you.

Thanks for the video good d

Thanks!

There is also a bracket that bolts to the trans and engine! Bolts near the passenger cv axle and the engine

I bought three fans in Spain they are motherfucker fraudster

Got the code on my acadia but took it to the dealership since it’s under warranty

Best tutorial I've seen on this. Thanks!

I’m

I follow your recommendation and my engine broke down --- you will hear from my lawyers

I had my 3rd purge valve replaced months ago and today I found the one that goes under was glued with the nipple broken. What part has to be replaced that has the nipple? Really pisses me off that this should have been a recall. I took my car back to the mechanic to ask why he used JB Weld. I was dumb enough to leave my car with him and he denied using JB Weld then went ahead and fixed it without telling me anything and since he denied it charged me $397.00. Telling me maybe when you got your oil changed they did it. My husband changes my oil. Noone else has touched my car since that repair.

great video!!! you ROCK! thank you so much

Great video. I have the P0014 code and will replace the VVT solenoid tomorrow. Thank you for explaining bank 1 and bank 2.

I was wondering would that show up on a scan tool Thanks for the help no doubt I'll be experiencing that Some day 😄

I took my beauty cover off and never put it back on. Retains too much heat on components

i think this is why im getting p0164

Does anyone know where to get a solenoid pressure control b for a 2010 Nissan Murano sl and does any one know where to get the diagram for the solenoid layout for this vehicle ?

The GM part for this sensor has a taller black plastic tip to it (where the plug goes into). It is too tall for that particular socket used in this video, So you would have to use a deeper socket which basically means you would have to remove that intake. Solution is to buy a generic part from O'reilly that has a shorter black plastic tip.

This is awesome bro, please post more stuff like this ❤

Did you just say in the beginning of video improvement of your sex life??? What the what

I have shift solenoid A code, p0746: will this fix my maxima

Don’t just replace the thermostat. Also replace the temperature sensor. The cost of the sensor is minimal if you find out later that the sensor was the problem all along. Sending a false reading to the ECM. Don’t ask me how I know!

Putting the wire did absolutely nothing 🤣

Can the intake manifold be repaired? My car is going 100 miles per hour when I press the gas pedal. The car does not accelerate at all, as if it is locked, so the engine light is on on the speedometer.

What year?

thanks for video

Best nissan altima 3.5 v6 video ever. Very informative and finally a 3.5 v6 with all sensors exposed. Thank you boss man. Beautifully done.

Great Video Brother ! I have a 94 4.0 I need to do valve cover gaskets! Keep up the great Videos!

I GOING TO DO IT , I HAVE THE SAME PROBLEM, BUT I DON'T KNOW IF IS THE TURN SIGNAL SWITCH OR ANTHER PART UNDER THE DRIVE WEEL.

Unfortunately didn’t work for me😩

Been looking for this! I have an 07 with nearly 300k on it and she still runs great, but would love to pull the engine and do a complete rebuild on it. Doesn’t look nearly as difficult as I had feared.

You make the job so difficult for not removing the filter housing and the throttle body

Im sorry i couldnt hear you over your acc**ent where are you from?

Thank you for this.

What is the part # for the magic fingers?

Thank you for the video I went out today and got the purge valve kit you mentioned. It is a simple kit you cut the old purge valve out it comes with 4 quick disconnects 2 straight lines 2 elbows. Put the quick disconnects on and reconnect the lines now you got the quick disconnects to use the kit in the future.

Let's do a colab video. This was great

Pause it pause it

VVT censor dónde se ubica

I bought a E250 2007 and would like to know if the 2010 steering wheel works?

I have this issue with my 2000 Deville. I do not plan to keep it much longer so I will try this. I do have a different issue I could use some help with. Do you know where I can find a diagram of how or how the rear window washer hose run from the washer reservoir to the rear window wiper?